PPA POP PLUS User manual

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1

P05642 - Rev. 1
WARNING
Do not use the equipment
before reading the
instruction manual.
COMMAND BOARD
POP PLUS
Factory Default Setting
Course time 1Min, maximum time
Time of Auto Disabled
Garage Light
Time / Delay Level 2, 80sec
Reversal Enabled
Brake Level 1
Strength Level 7, maximum
Limit Switch Open limit Disabled
Limit Switch Close limit Disabled
Limit Switch speed Level 4
DEFAULT TABLE
1 - Default Open Function 1xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
2 - Auto Time Open Function 2xCMD Enter Function 1xGRV Increase 1xGRV Decrease 1xCMD
3 - Erase TX Open Function 3xCMD Enter Function 1xGRV 1xGRV Cancel 1xCMD
Open Function 4xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
5 - Reversal Open Function 5xCMD Enter Function 1xGRV Enable 1xGRV Disable 1xCMD
6 - Brake Open Function 6xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
7 - Strength Open Function 7xCMD Enter Function 1xGRV Increase 1xGRV Decrease
1xCMD
8 - Limit Switch Open Limit Open Function 8xCMD Enter Function 1xGRV Decrease Distance 1xCMD
9 - Limit Switch Close Limit Open Function 9xCMD Increase Distance 1xGRV Decrease Distance 1xCMD
FUNCTION TABLE
Enter Function 1xGRV
Increase Distance 1xGRV
10 - Limit Switch speed Open Function 10xCMD Enter Function 1xGRV Decrease Speed
1xCMD
Increase Speed
1xGRV
4 - Garage Light
Time / Delay
Confirm
Confirm
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
TM
TECHNICAL
MANUAL
ELECTRICAL CONNECTIONS DIAGRAM
MOTOR DE
INDUÇÃO
MONOFÁSICO
REDE
ELÉTRICA
127V/220V
JUMPER DE
SELEÇÃO DA
TENSÃO
JUMPER DE
PROGRAMAÇÃO
LEDs DE
SINALIZAÇÃO
MÓDULO RELÉ LUZ DE
GARAGEM (OPCIONAL) CAPACITOR DE
PARTIDA DO MOTOR
MÓDULO RELÉ TRAVA
(OPCIONAL)
FOTOCÉLULA
BOTOEIRA
BOTÕES DE
CONFIGURAÇÃO
FCF FCA
FIM DE CURSO
MAIN CHARACTERISTICS
- Analogic Limit Switch;
- 433,92MHz Receptor Module;
- 18 controls recording;
- Electronic clutch adjustment (strength);
- Automatic memorization of course A/F;
- Inputs:
Photocell, uses external source;
Pushbutton;
- Outputs for modules:
Lock;
Garage lights;
- Brake adjustment;
- Limit switch adjustment;
- Limit switch speed adjustment;
- Opening delay time for signaling device.
FACTORY STANDARD
Restore settings to the factory default.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 1x and then GRV to enter
function
3. Press GRV to confirm factory default or
CMD to cancel and return to the function
menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x whenever it recognized button
as pressed
SIGNALING LED SN2:
-Flashes 1x;
AUTOMATIC TIME / SEMI
AUTOMATIC
At the end of the opening cycle, the gate
waits for the set pause time and closes
automatically when automatic is enabled.
The SN1 and SN2 LEDs flash together
every 1 second indicating decreasing time.
When the pause time is set to Disabled the
gate waits for the next command to close.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x while not
pressing CMD button
2. Press CMD 2x and then GRV
to enter the function
3. Press GRV to increase the
standby time in automatic mode or CMD to
decrease the time.
4. Zeroing the time the gate stays in the
semi-automatic function;
5. Step of 10s and maximum of 120 seconds;
6. Remove PROG jumper;
Values:
0 = Automatic disabled;
1 = 10 sec pause;
2 = 20 sec pause;
...
12 = 120 sec pause;
SIGNALING LED SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes 1x for 10s of the time, eg: 30s
pause, led flashes 3x;
- Automatic direct flashing disabled;
- Remains on when maximum time;
LED SIGNALING SN2:
- Blinks 2x;
ERASE TRANSMITTERS
Erase memory to record new transmitters.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button
2. Press CMD 3x then GRV to enter function
3. Press GRV to delete transmitters or CMD
to cancel and return to the function menu;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes 10x fast confirming exclusion
transmitters;
SIGNALING LED SN2:
- Flashes 3x;
GARAGE LIGHT TIME / DELAY
Setting the time to turn off the garage light
relay module when the gate reaches the
closing limit switch or the waiting time for
the gate to start to open after the activation
of the relay module connected to the
"LIGHT" output.
For Garage Light Time:
The setting has levels from 0 to 6,
maximum time of 4 minutes.
Operation: The garage light will turn on
whenever the gate is in motion or open for
a new command, and will be turned off
when the gate closes fully and after the
scheduled time has elapsed.
For Opening Delay with Signal On:
The setting has levels from 7 to 10,
maximum time of 15 seconds.
Operation: When the gate is fully closed
and when it receives a command for the
opening cycle, the signal will be turned on
and on for the set time and then the motor
will be activated. The signal will be switched
off at the end of the door closing cycle or
when a new command is received by the
transmitter during the delay time.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 4x and then GRV to enter the
function;
3. Press GRV to increase garage light off
time or CMD to decrease;
4. Time step of 40 seconds;
5. Maximum time for garage light is 4
minutes;
6. Delay setting times are 3sec, 7sec, 11sec
or 15sec;
7. Remove PROG jumper.
Levels
0 - signal
1 - 40sec
2-80 sec
6 - 240 sec
7 - 3 sec
8 - 7 sec
9-11 sec
10 - 15sec (maximum)
LED SIGNALING SN1:
- Flashes 1x when recognizing button
pressed;
- Flashes continuously to minimum time,
level 0;
- Remains on when maximum time;
- Flashes 1x at each level, eg level 6, led
flashes 6x.
SIGNALING LED SN2:
- Pex 4x;
REVERSAL
Push button or transmitter control permits
to operate during the door closing path for
reversal.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 5x and then GRV to enter the
function;
3. Pressing GRV enables reversal and CMD
disables;
4. Remove jumper PROG;
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Continuous Blink: reversal disabled;
- Remains enabled: Reversal enabled;
SIGNALING LED SN2:
-Pex 5x;
BRAKE
When there is a command to switch off the
motor, the brake will be activated with the
possibility of adjusting the sensitivity.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 6x and then GRV to enter
function;
3. Press GRV to increase brake sensitivity;
4. Press CMD to decrease the brake
sensitivity;
5. In the minimum value the brake is
disabled, with the possibility of adjustment
of 10 levels of sensitivity.
LED SIGNALING SN1:
- Flashes continuously for setting Minimum,
brake disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 10;
FORCE (ELECTRONIC CLUTCH)
Adjust the engine operating force.
In order for the use of this safety-sensing
device to be effective, proceed as follows:
- After proper installation of the automation
at the gate, adjust the electronic clutch; so
that the force is the minimum required to
move the gate leaf throughout its path,
opening and closing;
- At the end of the adjustment, test the
function by blocking the movement of the
gate by placing a rigid object in the course
of the gate.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 7x and then GRV to enter the
function;
3. Press GRV to increase the force or CMD
to decrease;
4. Maximum strength level is 7;
5. Remove PROG jumper;
LED SIGNALING SN1:
- Press 1x when acknowledge button
pressed;
- Continuous blink for minimum strength,
level 0;
-It remains lit for maximum strength, level
7.
-Speed 1x according to selected level, eg:
level 3, led flashes 3x.
SIGNALING LED SN2:
-Pex 7x;
Adjusting the limit Switch
The limit switch is the distance remaining to
reach the mechanical stop.
The control unit will continuously monitor
the position of the gate and when it
reaches this limit, the speed of operation
reduces, reaching the mechanical stop
gently.
1. With the gate stopped closing the PROG
jumper, led SN1 will flash 2x while not
pressing the CMD button;
2. Press CMD 8x for opening limit switch, or
press CMD 9x for closing limit switch and
then GRV to enter function;
3. Press GRV to move the limit to the
mechanical stop, increasing the distance;
4. Press CMD to decrease the distance to
the limit switch;
5. In the minimum value the limit switch is
disabled, not reducing the speed, with the
possibility of adjustment of 5 levels of
sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously for minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 5;
- It remains lit at maximum value.
SIGNALING LED SN2:
- Flashes 8x for opening;
- Flashes 9x, for closing.
LIMIT SWITCH SPEED
The control unit will decrease the speed of
operation as soon as it reaches the
programmed limit limit. The speed is the
same for opening and closing.
1. With the gate stopped closing the PROG
jumper, led SN1 will start flashing 2x while
not pressing the CMD button.
2. Press CMD 10x and then GRV to enter the
function;
3. Press GRV to increase speed;
4. Press CMD to slow down;
5. At the minimum value the limit switch is
disabled, it does not enter the slow down
speed, with the possibility of adjusting 11
levels of sensitivity.
LED SIGNALING SN1:
- Flashes 1x when acknowledge button
pressed;
- Flashes continuously to minimum setting,
disabled;
- Flashes 1x for each increment of
sensitivity, with maximum value equal to 11;
- It remains lit at maximum value.
SIGNALING LED SN2:
-Pex 10x;
RECORD TRANSMITTERS
PPA standard transmitters.
1. With the gate stopped, close the PROG
jumper, led SN1 will flash 2x
2. Press transmitter button, led SN2 will
start flashing whenever it receives a valid
code;
3. Press and release GRV button;
4. Release transmitter button;
5. Transmitter recorded successfully LED
SN1 and SN2 blinks;
6. Button already registered blinks led SN1
2x;
7. Full memory blinks led SN1 3x;
8. To record a new transmitter back to step
3;
9. Remove PROG jumper to finish;
DELETING A ROUTE
Return travel time to 1 minute
1. Gate must be stopped
2. With Jumper PROG opened, press GRV +
button for 3 seconds;
3. LED SN1 and SN2 should flash,
confirming operation
EXTRA SIGNALING ON LEDs
- Starting and leaving the program:
Led SN1 (red) flashes 1x, slowly
- Last Command - Opening:
Led SN2 (green) flashes 3x fast
- Last Command - Closing:
Led SN1 flashes 4x fast
- Photocell triggered:
Led SN1 remains lit.
LIMIT SWITCH
PROGRAMMING
JUMPER
PHOTOCELL
PUSH BUTTON
CONFIGURATION
BUTTONS
SIGNALING
LEDS
LOCK RELAY MODULE
(OPTIONAL)
GARAGE LIGHT RELAY
MODULE (OPTIONAL) ENGINE START
CAPACITOR
SINGLE-PHASE
INDUCTION
MOTOR
ELECTRICAL
NETWORK
127V/220V
VOLTAGE
SELECTION
JUMPER
P05631 - Rev.1