PR TANGO 100 BEAM User manual

1
TANGO 100 BEAM
PR-6801
The user manual contains important information about the safe installation and use of a projector. Please read
and follow these instructions carefully and keep the manual in a safe place for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2
INDEX
1.
SAFETYAND WARNINGS…………………………………………………………………………………………
3
2.
INSTRUCTIONS……………………………………………………………………………………………………
4
3.
INSTALLATION……………………………………………………………………………………………………
5
4.
SETUPAND CONFIGURATION……………………………………………………………………………………
7
5.
OPERATIONMENU…………………………………………………………………………………………………
8
6.
DMX PROTOCOL…………………………………………………………………………………………………
9
7.
TECHNICALDATA………………………………………………………………………………………………
10
8.
CIRCUIT
DIAGRAM………………………………………………………………………………………………
12
9.
COMPONENT ORDER CODES……………………………………………………………………………………
13
ACCESSORIES
The following items are supplied with the projector and please check:
Name
Quantity
Unit
Remark
Safety cord
1
Pc
User manual
0
Pc
QR Code
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice.
Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product
improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit.Any
damage caused by improper use will not be assumed by the manufacturer and / or dealer.
Any future technical change in the user manual won’t be with any further notice.
Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from the delivery date
but the light source is not within the warranty.

3
1. SAFETYAND WARNINGS
.
NOTE
Before a projector’s installation, power-on, operation and maintenance, please carefully read
the safety information hereinafter!
The following safety signs are used in the user manual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
●When unpacking, check if there is transportation damage before using a projector. Should there be any damage
caused by transportation, consult your dealer and do not use it.
●The manufacturer is not responsible for any loss caused by the user not following the manual or changing a
projector as he/she likes.
●Please be noted that the damage caused by changing a projector at will is not warranted.
●Do not hesitate to contact the dealer or the manufacturer if any questions or advice.
●If a lamp is damaged or deforms because of heat, it should be replaced.( It applies only to traditional lamps)
●The projector is for indoor and outdoor use, IP65.
●It can be used in humid and dusty areas.And it can contact water and other non-corrosive liquids.
●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while
being operated
●The projector is only intended for installation, operation and maintenance by qualified personnel. And the
operation must strictly follow the procedures in the manual
●No repairable parts in the projector and do not open covers for maintenance by yourself.
●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.
●Do not connect a projector to any type of dimmer pack.
●If the lamp, lens and screen protective cover of the a projector have obvious damage, i.e., to the extent that it
hurts the performance like cracking or deformation. Please stop using it and replace them with the original parts,
otherwise its performance will be compromised.
●For the installation location of a projector, it shouldn’t be seen in the distance of less than 4 meters for a long
time.
●Before operation, please confirm that all covers (housing) are on and screws tightened. It’s forbidden to use a
projector while covers (housing)are off .
●Keep the lamp clean and do not touch it with bare hands.
●While operating it, wear protective items like eye goggles , gloves and etc..
●Any electrical connection must be carried out by a qualified person .
●Before installation, please confirm the voltage supplied matches what is required for a projector.
●Each projector must be properly earthed and installed as per related electrical standards.
●Do not use power cord with its insulator damaged and connect the power cord with other cables.
●If a projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or by
pulling the power cable.
●All power cords must conform to related safety and regulations.

4
●If a projector is not water and dust proof, while being operated it should not be under rains or in humidity to
avoid short circuit.
●Do not switch on and off a projector constantly in very short intervals, otherwise the light source’s and other
electrical parts’life will be shortened .
●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord
supplied through the safety cord holes for safety support.
●Before any installation, maintenance and cleaning work, please ensure a projector is disconnected from power
mains.
●While running normally under normal ambient temperature, the temperature of the external surface of the metal
housing of a projector including that of the heat sink may reach 55℃ at maximum.
●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not
mean a projector has some defects.
●While it running, don’t touch the metal housing to avoid being burned!
●Do not mount a projector directly on inflammable surface.
●Do not project the beam straightly on combustible items and the minimum distance between a projector
and illuminated items is 10m.
●A projector should be installed with good ventilation and the minimum distance between a projector and a wall
is 50cm.At the same time, please ensure the fans and air inlets and outlets are workable.
●Do not let the front lens under sunlight or other strong light sources at any angle, otherwise the danger of fire
can be caused by the focused beam by the lens inside a projector.
●The product meets The General Technical Requirements and Standards for Recycle and Use Of Expired
Appliance and Electronic Products.
●When the product meets disposal standards and needs to be disposed, a client needs to dispose and recycle it.
2. INSTRUCTIONS
●CLEANINGAND MAINTENANCE
If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the
projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the
projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,
restart the projector.
The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to
ensure a reliable use of it. Cooling fans need to be cleaned every 15days.
Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning
work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean
and do not touch optical parts with bare hands.
Special note:
It’s normal phenomena that there will be mild water mist on the lens while the waterproof product is in use.
●Before any maintenance and cleaning, please ensure the project is off the power
●Only qualified person is allowed to do maintenance

5
●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether it
runs or not
●Do not use alcohol or other organic solvent to clean the housing to avoid damage.
●Do not use any detergent with chemical elements to clean color filters with coatings.
●LUBRICATION
To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and
focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised..
●TROUBLESHOOTING
PROBLEM
ACTION
The projector doesn’t switch on
Check the power cord connection
Power Switch fails or is not connected well, call a professional
technician for repairing and checking
Control board is not connected normally, call a professional technician
for repairing and checking ,
The project can be turned on, but the LED lamps
can’t be on
LED lamp board is not connected well, call a professional technician for
repairing and checking
The LED lamps can be on, but not controlled
by DMX
Check if DMX StartAddress is properly set
Check if XLR cable fails or not
The brightness decreases obviously
Ambient temperature is too hot which makes the projector too hot,
please take appropriate ventilation measures
3. INSTALLATION
●RIGGING
Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a
projector with power while it is locked.
Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole unit on the truss,
tighten the clamp’s retainers to keep the unit stable. (See the WARNING on the underside of the base as shown above) To pass the
SAFETY CORD through theARM for safety!Always ensure that the unit is firmly anchored to avoid vibration and slipping whilst
functioning. Always ensure that the structure that you are going to mount the unit to is secure and strong enough to support the weight
of the unit
Clamp
Safety Cord
Warning!
For safety, please run the safety cord through
the arm or its hole .

6
WARNING:
●The projector MUST be lifted or carried by the HANDLES instead of clamps.
●.For safety the safety cord should afford 10 times the Projector’s weight.
●POWER CONNECTION
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projector be connected with power separately so that they may be individually switched on and off.
●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in
accordance with the standards concerned.
●If any questions about the electrical installation, do not continue but consult a qualified electrician.
●DMX CONTROLCONNECTION:
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
terminator as shown in the figure below.
●DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

7
electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged
into the output socket on the last projector in the chain. The connections are illustrated below.
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
4. SETUPAND CONFIGURATION
●FRONT PANELOPERATION
The projector’s functions and start address can be conveniently set viabuttons and LCD screen.
To browse through or modify the projector’s functions, press key ENTER for more than 2 seconds to unlock the control panel and the
screen displays its function menu. Each main function menu has its sub-menus, and each submenu stands for its respective function.
For the details, please see the following:
To set or browse through the projector’s functions, press key UP or DOWN.
Press the key ENTER to save your settings or enter into the submenus. Press key UP or DOWN to change values(plus or minus)
Press key FUNC, it will return to the upper menu. If the key not pressed, the system will go back to display status automatically.
●DMX STARTADDRESS
Each Projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller. The Unit has 1 DMX modes, which is standard mode. For standard mode, it has 8 channels, so set the No. 1 projector’s
address 001, No. 2 projector’s address 09, No. 3 projector’s address 017, No. 4 projector’s address025, and so on.
Launch the projector. Press button ENTER more than 3seconds to unlock panel.
Press button ENTER to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; after powered on next time, the default will be last value saved
Press button FUNC, it will return to the upper menu
.
●STAND-ALONE MODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
●MASTER/SLAVE MODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

8
StartAddresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’and Slaves’operation mode can
be set accordingly
After Powered on, the group will run in Master/Slave Mode
5. OPERATION MENU
1st level menu
2nd level menu
3rd level menu
4th level menu
Address
001 - 512
DMXAddress
Config Setup
MasterSlave
Slave
Default ：Slave
Master
Moto Offset
Color
000 - 255
Focus
000 - 255
RPrism
000 - 255
Prism
000 - 255
Clean Progra
Yes
PRM Transmit
Yes
Factory Setting
Yes
Factory Config
000 - 255
Display Invert
Yes
No
Lcd Light Setup
On
Backlight will be turned
off 3 minutes after no key
is pushed
Off
Language Setup
English
Default ：English
Chinese
Moto Reset
Yes/No
Information
LED Temperature
XX
Fixture use Time
XXXX
Software Version
X.X.X
Test Mode
Auto Test
Dimmer
000 - 255
Brightness of LED lamp
Color
000 - 255
Motor position
Prism
000 - 255
Motor position

9
RPrism
000 - 255
Motor position
Focus
000 - 255
Motor positon
Operation Mode
DMX Mode
Yes
User Memory
Yes
Preset Memory
（PR01~ PR16）
PR01~ PR16
User Progra Edit
（ET01~ET16）
Dimmer
000 - 255
Strobe
000 - 255
Color
000 - 255
Prism
000 - 255
RPrism
000 - 255
Focus
000 - 255
Keep Time
00 – 200 (0- 20S)
6. DMX PROTOCOL
Function
DMX Value
Description
1
Dimmer H
000-255
Linear dimmer
2
Dimmer L
000-255
Dimmer in 16 bit
3
Strobe
000-007
No strobe
008-255
Strobe from slow to fast
4
Color wheel
000-007
White
008-015
White - Red
016-023
Red
024-031
Red - Yellow
032-039
Yellow
040-047
Yellow – Light Blue
048-055
Light Blue
056-063
Light Blue - Blue
064-071
Blue
072-079
Blue – Light Green
080-087
Light Green
088-095
Light Green– Orange
096-103
Orange
104-111
Orange– Purple
112-119
Purple
120-127
Purple– White
128-191
Clockwise rotation from slow to fast
192-255
Anti-clockwise rotation from slow to fast
5
Prism
000-127
Close
128-255
Open

10
7. TECHNICALDATA
Input voltage: 100V~240VAC，50/60Hz
Input power: 100W @ 230V
Maximum current: 0.6A
Power factor：PF>0.9
LIGHT SOURCE SPECIFICATIONS
LED lamp : White
Power Consumption : 80W
Manufacturers Rated Lamp Life: 20000hours
Color temperature: 6200K
COLORS
1color wheel :7 colors+ white
Bi-direction rainbow effect with variable speeds
Stepping/linear color changing
DIMMER
Linear Dimmer from 0-100%
FOCUS
DMX linear focusing
STROBE
Electronic Strobe 0-25FP.S. with preset strobe pulse effect
BEAMANGLE
Beam angle :2.0°
CONTROL
International standard DMX512 signal control protocol and 5 pin interfaces
Standard mode 8 channels
HOUSING
CastAluminum , high temperature/anti-UVABS, IP65
NET WEIGHT
6
R Prism
000-127
Motor position
128-189
Clockwise rotation from fast to slow
190-193
Stop
194-255
Anti-clockwise rotation from slow to fast
7
Focus
000-255
Motor position
8
Function
000-199
No
200-209
Motor reset

11
9.0Kg
OPERATION TEMPERATURE:
Maximum ambient temperature 40 ℃
SIZES( unit: mm)
SUPPORT SIZE( unit: mm)
LIGHT OUTPUT

12
8. CIRCUIT DIAGRAM

13

14
9. COMPONENT ORDER CODES
Name
Code No.
Qty.
Specifications
200W switching power supply
6190000008A
1
LED constant current source
6190000016
1
80W light source
6150000042
1
Stepper motor
6030040001
2
Stepper motor
6030040254
2
Stepper motor
030040073B
1

15
PR LIGHTING LTD.
1582 XingyeAvenue, Nancun Panyu
Guangzhou, 511442 China
TEL: [phone]
PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products.
Counterfeiting Will be Prosecuted!
P/N: 320021548
Old Version: 20231025
New Version: 20231102