Precision Digital Corporation ConsoliDator+ User manual

MULTI-CHANNEL CONTROLLER
• NEMA 4X Panel or Field Mount Multi-Channel Controller
• Convenient Display, Control, & Alarm of Multiple 4-20 mA & Pulse Inputs
• Numeric & Bargraph Color Display (320 x 240 pixels) 5.7" (145 mm)
• Sunlight Readable Display, White Backlight
• Isolated 24 VDC Transmitter Supplies 200 mA / Analog Input; 1,600 mA Max
• 99 Channels, 32 Totalizers, 32 Timers, & 199 Modbus Slave Inputs
• 64 High & Low Alarms assigned to up to 25 Relays with AND/OR Logic
• Modular Design for Input & Output Flexibility
• Up to (28) 4-20 mA Isolated Inputs or Pulse Inputs
• Up to (25) 10 Amp Form C Relays (With Eight Analog or Pulse Inputs)
• Up to (25) Isolated 4-20 mA Outputs (With Eight Analog or Pulse Inputs)
• Operating Temperature Range: -40 to 60°C (-40 to 140°F)
• Pulse, Analog, & Modbus Input Flow Rate / Total / Grand Total Capability
• 50-Point Linearization, Square Root, and Exponent for Open Channel Flow
• Round Horizontal Tank Volume Calculation; Just Enter Diameter & Length
• Multi-Pump Alternation Control or Simple On / Off Control
• Programmable Displays, Function Keys & Digital Inputs
• Math Functions: Sum, Diff, Average, Multiply, Divide, % Efficiency, & More
• Display Direct Modbus PV Inputs – Slave Mode
• RS-485 Modbus RTU Standard & Ethernet Modbus TCP/IP Optional
• Free ConsoliDator+ Configuration Software
• 3 Year Warranty
www.predig.com
PRECISION DIGITAL CORPORATION
Field Mount
Panel Mount
PD9000 ConsoliDator+
Multivariable Controller

www.predig.com
PD9000 Multi-Channel Controller
22
OVERVIEW
The ConsoliDator+ is a multi-channel controller that is both easy to use and satises a wide variety of process display, alarm
and control applications. It accepts 4-20 mA inputs, ow meter pulse inputs, digital inputs, and Modbus RTU inputs and
displays them both in numeric and bargraph format on a large, 5.7" color display. It can be equipped with multiple relays with
user-denable actions, 4-20 mA outputs, digital outputs, Modbus RTU, and Ethernet Modbus TCP/IP protocol communication
capabilities. Additionally, the controller is equipped with up to 32 timers that can be used to control many processes or events.
All this functionality is easily programmed using free software or via the front panel pushbuttons. Choose the model that best
suits your application, from monitoring only to fully loaded controllers with an extensive combination of inputs, outputs and
communication protocols. The standard product o󰀨ering is listed in the ordering guide and other models are available for
special order.
SCREENS
The ConsoliDator+ can be programmed to display the data on up to 20 di󰀨erent screens in a variety of formats, with and without
bargraphs. The following screens show a typical main screen and channel details screen:
Channel Details Screen
Screen Name
Display from
1 to 8 PVs and
bargraphs on
screen
Alarm Set and
Reset Points
indicated on
bargraph
Sunlight readable display
Commas
available for
easy reading of
large numbers
Channel
Number & Tag
PV and Units
NEMA 4X Front
Main Screen
Bargraph with
Alarm Points
Channel Number
and Tag
PV & Units
Input Card
Slot Number
Alarm Set & Reset Points
and Status
Input Current (mA)
Timer Status

www.predig.com
PD9000 Multi-Channel Controller
3
INPUTS & OUTPUTS
If all Input / Output slots are used exclusively for one function, the ConsoliDator+ can accept up to (28) isolated 4-20 mA and pulse inputs,
(25) isolated 4-20 mA outputs, and (25) relays. See the Ordering Guide for standard congurations. In addition, the ConsoliDator+ has
digital inputs and outputs and RS485 capabilities as standard and Ethernet as an option. The following shows the connections for a
ConsoliDator+ with four pulse inputs, eight isolated 4-20 mA inputs, 10 isolated 4-20 mA outputs and 10 Form C relays.
PI-1 PI-2 PI-3 PI-4
AI-5 AI-6 AI-7 AI-8
AI-1 AI-2 AI-3 AI-4
ANALOG OUTPUTS
ANALOG OUTPUTS
RELAYS
RELAYS
AO-1 AO-2 AO-3 AO-4 AO-5
AO-6 AO-7 AO-8 AO-9 AO-10
RY-1 RY-2 RY-3 RY-4 RY-5
RY-6 RY-7 RY-8 RY-9 RY-10
DIGITAL
INPUTS
DC
PWR
ETHERNET
MICRO
USB
DIGITAL
OUTPUTS
RS-485 AC
PWR
I+ Ex+ I- I+ Ex+ I- I+ Ex+ I- I+ Ex+ I- I+ Ex+ I-
I+ Ex+ I- I+ Ex+ I- I+ Ex+ I- I+ Ex+ I- I+ Ex+ I-
C NC NO C NC NO C NC NO C NC NO C NC NO
C NC NO C NC NO C NC NO C NC NO C NC NO
S- S+ S- S+
mA- mA+ 24V mA- mA+ 24V mA- mA+ 24V mA- mA+ 24V
mA- mA+ 24V mA- mA+ 24V mA- mA+ 24V mA- mA+ 24V
S- S+ S- S+ -
+
Gnd
N
L
G
+
1
2
3
4
5
1
2
3
4
G
D+
D-
G
PULSE INPUTS
4-20 mA INPUTS
4-20 mA INPUTS
Notes:
1. Each 4-20 mA input has its own isolated 24 VDC power supply to power the transmitter.
2. Each 4-20 mA output has its own isolated 24 VDC power supply to power the output loop.
3. Each relay is Form C and rated at 10 A.
4. Input / output connections are made to removable screw connectors.
5. Every ConsoliDator+ has ve digital inputs (additional digital inputs can be obtained by using the Pulse Inputs).
6. Every ConsoliDator+ has four digital outputs.
7. Every ConsoliDator+ has RS-485 with Modbus.
8. All ConsoliDator+ models can be powered from either AC or DC Power.
9. Ethernet with Modbus TCP is an option.
10. Micro USB is used for programming the ConsoliDator+.

www.predig.com
PD9000 Multi-Channel Controller
4
Auto-Generated
Channel #: User-editable
to re-order channels Channel Tag: User editable
Function: Applied
to input source
Input: Source
for channel
Units: Engineering
/ time or none
Decimals: Number
of decimals for PV
Scale: Enter input
and output values
Cuto󰀨: PV goes
to zero below the
cuto󰀨 value
Display Bargraph:
Display on screen
Bargraph Scale:
Set the 0 and
100% values
Soft Keys:
Change based
on the screen in
place
SETTING CHANNEL PARAMETERS
What makes the ConsoliDator+ easy to program is its intuitive setup screens. As shown in the rst image below, the setup screen
allows you to see all the relevant information you need when creating or editing a channel - all on one screen! When creating
a new channel, the channel number is auto-generated for you. All you have to do is populate the appropriate elds such as
the channel tag name, function, input, and units. Scaling the inputs and outputs, selecting number of decimals, and turning the
bargraph on/o󰀨 and inputing its values are also programmed from this screen. During programming, the soft keys will change
based on the screen in place. For instance, pressing the edit key will bring up the letters/numbers key pad and appropriate
navigation keys will appear (Shown in the bottom image). See the PD9000 manual for details on setup and programming.
Soft Keys:
Change based
on the screen in
place
Letter and Numbers
Key Pad: Used
to input text and
numbers in text elds
Text / Numbers
Input Field
Numbers Key Pad
Button: pressing
this will bring up the
numbers key pad
Text Field
Editing Buttons

www.predig.com
PD9000 Multi-Channel Controller
5
INDIVIDUAL CHANNEL VIEW
To view the details of any channel, press Menu and then press
View – Channel. Select the channel of interest. Navigate
through the di󰀨erent items using the navigation keys. A green
bar indicates the selected item, press the R-key to step into and
see more details about the inputs and outputs related to the
channel in view.
In the following examples, the screens show all the parameters
associated with Channel 1 including analog input, slot number
and its current value, setpoints and status of alarms, and analog
output and its mA value. The bargraphs in each of these screens
examples represent the current value in gallon units.
Alarm set points are indicated by amber horizontal lines
Active Low Alarm: Indicated by red horizontal and vertical lines.
The top of the vertical line is the reset point of the low alarm. The
low alarm is indicated on the right side of the bargraph.
Active High Alarm: Indicated by red horizontal and vertical
lines. The bottom of the vertical line is the reset point of the
high alarm. The high alarm is indicated on the left side of the
bargraph.
Low & High Alarm Indication
If applicable, alarms may be acknowledged, and totals may be reset from the channel view screens. The alarm set points are indicated
by an amber line at the corresponding value on the bargraph.

www.predig.com
PD9000 Multi-Channel Controller
6
4-20 mA Analog Input Connections
Analog 4-20 Input connections are made to screw terminal
connectors (two inputs per connector). The following gures
show examples for typical applications. Each of the 4-20 mA
inputs may be connected in any of the modes shown below.
mA- mA+ 24V
- + -+
External
Power
Supply
2-Wire
4-20 mA
Transmitter
Analog Input
mA- mA+ 24V
- +
2-Wire 4-20 mA
Self-Powered
Transmitter
Analog Input
CONNECTIONS
Power connections are made to one of the power terminal
connectors. All units are capable of being powered either by AC
or by DC for the ranges specied.
90-264 VAC Power
● Use three-terminal power connector as shown in
Figure 1.
● Unit is protected internally with 1.25 A auto-resettable
fuse. 2 A max, slow blow, 250 V min UL Recognized
external fuse recommended.
24 VDC Power ± 10%
● Use two-terminal power connector as shown in
Figure 1.
● Unit is protected internally with 3.7 A auto-resettable
fuse. 4 A max, slow blow, 50 V min UL Recognized
external fuse recommended.
Gnd AC Power
90-264 V
47-63 Hz
N
L
+
-
Earth Gnd
AC Neutral
AC Line
DC -
DC +
DC Power
24 V
Note:
The controller may be powered by AC voltage with the 24 VDC
power connection used as backup power.
Figure 1. Power Connections
Isolated Input Signal Connections
Isolated input signal connections are made to removable
screw terminal connectors, which are labeled individually on
the back panel of the controller. The back panel shows the
type of input card installed in each slot (The top slot is #1 and
the bottom is #7). Individual inputs are referenced as PI-1 to
PI-4 for pulse inputs and AI-1 to AI-4, AI-5 to AI-8, etc for
analog inputs.
Figure 2. Transmitters Powered by ConsoliDator+’s
Isolated 24 VDC Power Supply
mA- mA+ 24V
-Pwr+
3-Wire 4-20 mA
Transmitter
Analog Input
mA- mA+ 24V
-
2-Wire 4-20 mA
Transmitter
Analog Input
Signal
Pwr+
Figure 3. Transmitter Powered by External Supply or Self-Powered
mA- mA+ 24V
3-Wire 4-20 mA
Transmitter
Analog Input
+
External
Power Supply
Signal +
Power +
Signal -
-
Figure 4. Three-Wire Transmitters Powered Externally

www.predig.com
PD9000 Multi-Channel Controller
7
Flow Meter Pulse Input Connections
Flow Meter Pulse Inputs are wired to four-terminal connectors
(two inputs per connector). A square waveform is used in the
illustration, but the input is capable of reading many other
types of signals within the voltage and frequency ranges
specied.
S- S+
Pulse Input
+
-
Signal Source
Figure 5. Flow Meter Pulse Input Connections
Digital Input Connections
Inputs are wired between terminals 1-5 of the digital input
connector and the G terminal of the 2-position connector
above the digital inputs. Normally open switch contacts may
be used as shown in Figure 6. The diagram also shows a
Digital Input using an NPN open collector transistor output
from a live signal. Logic LO or switch closure appearing
across the terminals is interpreted as ON. When using an
open collector transistor, a logic HI at the base (marked “B” in
Figure 6) will be interpreted as ON. The 2-position connector
has a +5 V terminal that may be used to provide excitation to
some sensors requiring more than the pull-up provided on
each digital input terminal.
G
Digital Inputs
+5V
1
2
3
4
5
Switch
Contact
Live
Signal C
E
B
Figure 6. Digital Input from Switch Closure and Live Signal
Analog Output Connections
The following gures show examples for isolated 4-20 mA
transmitter output connections. Terminal connectors are
labeled individually. The analog outputs are isolated from
each other and from the inputs. They are powered internally
to provide an active 4-20 mA output loop. The outputs may
be powered externally by connecting the positive voltage to
the Ex+ terminal.
I+ Ex+ I-
mA-mA+
Analog Output
Remote Display,
Chart Recorder, Etc
I+ Ex+ I-
mA-mA+
Analog Output
Remote Display,
Chart Recorder, Etc External
Power Supply
+
-
Figure 7. Active 4-20 mA Output Powered by ConsoliDator+
Figure 8. Passive 4-20 mA Output Powered by External Supply
Note: Analog inputs and outputs are isolated from each other.
Digital Output Connections
The digital outputs may be used to drive digital inputs, alarm
annunciators, or other devices such as solid state relays that
can be driven with low voltage signals.
Digital Outputs
on ConsoliDator+
1
2
3
4
G
Alarm
Annunciator
Load
V
AC
Figure 9. Digital Outputs Driving 5V Solid State Relay
and Alarm Annunciator

www.predig.com
PD9000 Multi-Channel Controller
8
Relay Connections
Relay connections are made to three-terminal connectors
labeled individually. There are ve relays per card.
Switching Inductive Loads
The ConsoliDator+ has internal circuitry to protect the relays
from inductive loads, however, the use of suppressors
(snubbers) is strongly recommended when switching
inductive loads to prevent disrupting the microprocessor’s
operation. The suppressors also prolong the life of the
relay contacts. Suppression can be obtained with resistor-
capacitor (RC) networks assembled by the user or purchased
as complete assemblies. Refer to the following circuits for RC
network assembly and installation.
C
NC
NO L
O
A
D
-
+
Internal Protection
MOV MOV
15kΩ
4.7nF
15kΩ
4.7nF
Figure 11. AC and DC Internal Inductive Load Protection
Figure 10. Relay Connections
For additional external protection choose R and C as
follows:
R: 0.5 to 1 Ω for each volt across the contacts
C: 0.5 to 1 µF for each amp through closed contacts
Notes:
1. Use capacitors rated for 250 VAC.
2. RC networks may a󰀨ect load release time of solenoid
loads. Check to conrm proper operation.
3. Install the RC network at the instrument's relay screw
terminals. An RC network may also be installed
across the load. Experiment for best results.
C NC NO
+
-
L
O
A
D
Use diode with a reverse
breakdown voltage two to
three times the circuit voltage
and forward current at least
as large as the load current.
RC Networks Available from Precision Digital
RC networks are available from Precision Digital and should
be applied to each relay contact switching an inductive load.
Part number: PDX6901.
Serial Communication Connections
The RS-485 port for serial communication (using Modbus
protocol) has three terminals labeled D+, D-, and G. It is
strongly recommended to use three-wire shielded cable
and to always connect the ground terminal to the other
equipment’s ground to avoid di󰀨erential voltage between
the systems. Distances up to 4000 feet can be reached with
RS-485. Up to 32 Modbus devices may be connected to a
single RS-485 bus.
ConsoliDator+
RS-485 Port
D+
D-
G
120 ohm
B+
A-
G
120 ohm
Last Modbus
Device
Terminating Resistor Terminating Resistor
Ethernet Option
The Ethernet port is available on the RJ45 connector. This
allows the ConsoliDator+ to connect to a local area network.
The Ethernet port option is congured using the Lantronix
DeviceInstaller software, available for download from the
Lantronix’s Website at www.lantronix.com/products/
xport. See the PD9000 ConsoliDator+ manual for ethernet
port setup details.
External Keypad Connections
Normally open pushbuttons may be wired to the digital inputs
connector for use when the front panel of the controller is not
accessible. The external keys may be assigned to replicate
the Menu and F1-F4 function keys.
Figure 14. External Keypad Connections
G
Digital Inputs
+5V
1
2
3
4
5
External Keypad
Figure 13. Serial Connections
Figure 12. Low Voltage DC Loads Protection
C NC NO

www.predig.com
PD9000 Multi-Channel Controller
9
SPECIFICATIONS
Except where noted all specifications apply to operation at 25°C (77°F)
General
Display: Color; QVGA (320x240 px), 5.7" (145 mm) diagonally,
white backlight Bargraph: Twenty divisions Numerical: Up to 15
digits (±999,999,999,999,999) Feet & Inches Format: 99,999' 11.9"
Screen Bargraph: Enable/disable: Channels, totals, timers
Bargraph scale: 0 – 100%, independent of channel scale. Twenty
divisions: 5% each. Screen: Select to show bargraph or not.
Decimal Point: 0 to 15 decimal places, user selectable
Engineering Units: User selectable units or custom units
Time, Distance, Volume, Pressure, Weight, Temperature, Current,
Voltage, Percent, Amps, Volts, Counts, Logic, and Custom, Any
unit/unit of time or other units
Display Update Rate: User selectable: 0.1 to 10 sec (10 updates/
sec to 1 update/10 sec)
Programming Method: Front panel buttons, external buttons, or
ConsoliDator+ Software
Number of Alarms: Up to 64 high or low Automatic (non-latching)
or latching On & Off time delays. May be assigned to one or more
relays. Note: Alarms are independent from relays.
Alarm Types: Single Source: One input
Multi-Source: Two or more inputs
Interval: Enter time interval and On Time
Alarm OR: Any active input alarm triggers the OR alarm
Alarm AND: All input alarms must be active to trigger the AND
alarm
Alarm Ack & Reset: Automatic only (Non-latching)
Automatic and manual
Manual only (Latching)
Manual with Ack only after alarm is cleared (Latching with Clear)
Internal Buzzer: 60 dBA @ 24 inches (61 cm) Enable/disable in
System – General menu. Associated with alarm Horn setting
External Horn (Sold separately): Assign any relay to the Horn
function to activate an external horn when alarm condition is
detected.
Calibration: All inputs and outputs are calibrated at the factory.
Field calibration not possible.
Input & Output Cards: Max Number of I/O Cards: 7
Analog Inputs: 4/card, Pulse Inputs: 4/card, Analog Outputs: 5/card,
Relays: 5/card
Number of Screens: Up to 20 screens with 1 to 8 PVs or items per
screen. Enable or disable screen title, channel #, and bargraph
Automatic or manual scanning Scan time: 1 to >1000 sec,
independent for each screen. F1-F4 keys are assigned per screen
Function Keys: User programmable (See defaults below) F1 =
Previous ← F2 = Next → F3 = Scan/Stop F4 = Ack
Number of Channels: Up to 99 channels
Input source: 4-20 mA, Pulse, Digital, Modbus, Alarm, Math,
Channel, Total, Timer, mA Output, Relay Output, Digital Output,
or Modbus Output
Password: Programmable password restricts modification of
programmed settings
Non-Volatile Memory: Settings stored for a minimum of 10 years.
Power (User Selectable Based on Wiring): Three-terminal
connector (L, N, GND), AC: 80-264 VAC, 47 to 63 Hz, 60 W max
DC: 113-370 VDC, 60 W max (L, N), Two-terminal connector
(G, 24V) DC: 24 VDC ±10%, 60 W max
Backup Power Supply: If AC and DC power are connected, the
24 VDC can be used as backup power in case of AC power failure.
Fuse: Unit is protected internally with auto-resettable fuse.
AC: 1.25 A max, DC: 3.7 A max
External Fuse: Recommended external fuse slow-blow
120 VAC: 2.0 A, 240 VAC: 1.0 A, 24 VDC: 4 A
Isolation & Grounding: 1500 V Analog inputs/outputs-to-power
line, 500 V Analog input-to-input, input-to-output, analog output-to-
output
All analog inputs and analog outputs are isolated from each other.
Note: DC Power is not isolated. DC- is connected to Earth Ground.
Digital I/O, USB, and Ethernet are grounded.
Environmental: Operating temperature range: -40 to 60°C
(-40 to 140°F)
Storage temperature range: -40 to 60°C (-40 to 140°F)
Relative humidity: 0 to 90% non-condensing
*All functions operate down to -40°C (-40°F.) If the LCD response
is slower, increase the display refresh setting.
Connections: Removable screw terminal blocks, Inputs/Outputs:
12 to 24 AWG wire, Digital I/O: 16 to 30 AWG, RS-485: 12 to 24
AWG wire RJ45 Ethernet connection. USB ports: Micro-USB
(Device) and Type A (Host)
Tightening Torque: Screw terminal connectors: 5 lb-in (0.56 Nm)
Digital I/O terminals: 2.5 lb-in (0.28 Nm)
Enclosure: Enclosure Body: Thermoplastic Polyester,
Color: Gray,
Display Window: Clear Polycarbonate, GE LEXAN HP12W
Front Panel Keys: Silicone rubber
Tamper Proof Enclosure: The field mount enclosure’s cover is
secured by a clasp that can be locked to prevent unauthorized
access to the enclosure’s interior.
Mounting: Wall-Mount: Four screws/bolts required (not provided)
Pipe-Mount: (2) U-Bolts for 2" Pipe (See Ordering Information)
Panel-Mount: Panel-mounting frame and twelve screws (provided)
Cutout: 10.0" x 10.0" ±0.05" (254 mm x 254 mm ±1.3 mm) (H x W)
Panel thickness: 0.07" – 0.35" (1.8 mm – 8.9 mm)
Clearance behind panel: 6" (152 mm)
Conduit Connections: There are four center punched marks
on each side of the field enclosure. Holes must be drilled by the
installer according to the desired conduit entry.
Size: ½" or ¾" (16 mm or 21 mm)
Clearance: 1.5" (38 mm) diameter
Overall Dimensions: Panel-Mount: 10.85" x 10.85" x 4.87"
(276 mm x 276 mm x 124 mm) (H x W x D)
Field-Mount: 11.5" x 12.0" x 8.03"
(292 mm x 305 mm x 204 mm) (H x W x D)
Weight: Ex: PD9000-XY-4PI-8AI-10AO-10RY
Panel-Mount: 7.4 lb (3.4 kg) approx.
Field-Mount: 10.8 lb (4.9 kg) approx.
Warranty: 3 years parts and labor

www.predig.com
PD9000 Multi-Channel Controller
10
4-20 mA Analog Inputs
Number of Inputs: (4) Analog inputs/card
(28) Analog inputs max, no other I/O
Typical Input: 4-20 mA
Input Range: 0-24 mA
Accuracy: ±0.03% of full scale ±1 count
4-20 mA Display Value: Up to six full digits (Recommended)
±999,999. More digits may be used, but the stability will be
affected. Increase the filter value and display update rate to get a
more stable reading.
Transmitter Power Supply: Isolated 24 VDC @ 200 mA/input
Max current: 1,600 mA (All inputs), (8) Analog Input @ 200 mA max
(28) Analog Input @ 20 mA max
Available on AC or DC powered units
Temperature Drift: Better than: 20 ppm/°C from -40 to 60°C
ambient
Filter: Window: 0.5, 1, 2, 4, 8 sec, IIR: 16, 32 sec
Glitch Filter: Discards a single sample caused by high frequency
noise
Filter Bypass: 0 to 100 % of full scale Filter is ignored, if the signal
change is greater than bypass value
Channel Input Scale Function: Linear 2-Point, Multi-Point (up to
50 points) Square Root, Programmable Exponent, Scale Factor,
Round Horizontal Tank (Volume), None (mA Input Reading)
Input Protection: Each 4-20 mA input is protected by an auto-
resettable fuse, 30 VDC max. The fuse resets automatically after
the fault condition is removed.
Input Impedance: 125 Ω Typical Including auto-resettable fuse
Isolation: 1500 V: Input-to-power line
500 V: Input-to-input, input-to-output
All analog inputs and analog outputs are isolated from each other.
Normal Mode Rejection: 100 dB at 50/60 Hz
Common Mode Rejection: 90 dB at 50/60 Hz
Pulse Inputs
Number of Inputs: (4) Pulse inputs/card, (28) Pulse inputs max,
no other I/O
Input Type: Active Square Wave, NPN, PNP, Reed Switch, Coil
(Magnetic Pickup)
Normal threshold: 1.2 V (0.8 to 3.0 V)
High threshold: 2.5 V (2.0 V to 6.0 V)
Coil threshold: 20 mV (Low) or 100 mV (High)
Signal Level: Active Square Wave: 0 to 30 V max
Typical: 0 to 5 V
Coil: 20 mVp-p to 30 Vp-p (Magnetic Pickup)
Input Impedance: Active, NPN, Reed: 10 kΩ pull-up to 5 V
PNP: 10 kΩ pull-down to (S-)
Coil: >2 kΩ (20 mV sensitivity), >10 kΩ (100 mV sensitivity)
Isolation: Pulse inputs are not isolated, (S-) terminal is connected
to system GND
Input Protection: ±36 V, non-isolated
Frequency Response & Signal Level:
Active Square Wave 5 V: 0 to 100 kHz
Coil (Magnetic Pickup): 0 to 50 kHz
Frequency – Signal level (Coil: 20 mV)
20 mVp-p – 100 Hz
100 mVp-p – 10 kHz
Frequency – Signal level (Coil: 100 mV) 100 mVp-p – 90 Hz
500 mVp-p – 5 kHz
20 Vp-p – 50 kHz
Minimum Frequency: 250 μHz High Gate: 4,000 sec
Gate: Low Gate: 1 to 99 sec
High Gate: 2 to 4,000 sec (Must be higher than low gate)
Accuracy: ±1 count for K-Factor > 1 or 30 ppm
K-Factor: Programmable pulses/unit with up to 15 decimal
resolution
Scale Pulse Input: Linear 2-Point
Multi-Point Scaling: 2 to 50 points
Modbus Inputs
Number of Inputs: 199 Modbus RTU
Scale MB Input: Modbus input may be used as the input for creating
channels and totals, the same way 4-20 mA inputs are used.
Data Type: Bit-Logic
Signed/Unsigned: 16 (Short), 32 (Long), 64 (Long-Long)
Float 32
Float 64 (Double)
Decimal Point: User selectable
Comm Break & Timeout: Specify what value to hold on comm.
break and how long to wait for new data before reporting a break
condition.
Input Action: Specify what should happen when new data is
written to the input register (e.g. add value to total).