PRECISION DIGITAL Sabre P PD603 User manual

PRECISION DIGITAL CORPORATION
SABRE P MODEL PD603
PROCESS METER
Instruction Manual
•0-20, 4-20 mA, 0-5, 1-5, 0-10, ±10 V Inputs
•Type 4X, NEMA 4X, IP65 Front
•Shallow Depth Case 3.6" Behind Panel
•4 Digit Display, 0.56" (14 mm) High, Red LEDs
•Easy Front Panel Programming
•Scale without a Signal Source
•Calibrate with a Signal Source
•Maximum/Minimum Display
•Universal Power Supply 85-265 VAC
•12-36 VDC/12-24 VAC Power Option
•24 VDC @ 200 mA Transmitter Supply Option
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
2
Disclaimer
The information contained in this document is subject to change
without notice. Precision Digital makes no representations or war-
ranties with respect to the contents hereof, and specifically disclaims
any implied warranties of merchantability or fitness for a particular
purpose.
© 2010-2016 Precision Digital Corporation. All rights reserved.
INTRODUCTION
The Sabre P model PD603 is an easy to use process input meter. It ac-
cepts 0-20 mA, 4-20 mA, 0-5, 1-5, or ±10 V input signals. The four front
panel buttons make the setup and programming an easy task.
The isolated 24 VDC transmitter power (optional) can be used to power
the input transmitter or other devices.
ORDERING INFORMATION
85-265 VAC*
Model 12-36 VDC* Model Description
PD603-6R0-0 PD603-7R0-0 Process Meter
PD603-6R0-1 Process Meter with
24 V transmitter supply
*All models may be powered from AC or DC, see Specifications for details.
NEMA 4 & NEMA 4X Enclosures
Model # of
Meters Description Mounting
PDA2500 1 - 6 Plastic NEMA 4X Enclosure Through Door
PDA2600 1 - 6 Stainless Steel NEMA 4X Enclosure Through Door
PDA2700 1 - 6 Steel NEMA 4 Enclosure Through Door
PDA2801 1 Plastic NEMA 4X Enclosure Through Cover
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
3
Table of Contents
INTRODUCTION------------------------------------------------------------ 2
ORDERING INFORMATION--------------------------------------------- 2
SPECIFICATIONS---------------------------------------------------------- 5
General-------------------------------------------------------------------------------5
Process Input----------------------------------------------------------------------6
COMPLIANCE INFORMATION----------------------------------------- 7
Safety---------------------------------------------------------------------------------7
Electromagnetic Compatibility-----------------------------------------------7
SAFETY INFORMATION ------------------------------------------------- 8
INSTALLATION------------------------------------------------------------- 9
Unpacking---------------------------------------------------------------------------9
Panel Mounting--------------------------------------------------------------------9
Connections---------------------------------------------------------------------- 10
Connector Labeling ---------------------------------------------------------- 10
Power Connections ---------------------------------------------------------- 10
Signal Connections ---------------------------------------------------------- 11
SETUP AND PROGRAMMING ----------------------------------------13
Front Panel Buttons and Status LED Indicators--------------------- 14
Display Functions and Messages----------------------------------------- 15
Main Menu ------------------------------------------------------------------------ 16
Setting Numeric Values ------------------------------------------------------ 17
Setting Up the Meter (
setu
) ------------------------------------------------- 18
Setting the Input Signal (inpt)-------------------------------------------- 18
Setting the Decimal Point (dec.p)----------------------------------------- 19
Programming the Meter (
prog
)--------------------------------------------- 20
Scaling the Meter (ScAL)---------------------------------------------------- 21
Calibrating the Meter (Cal)------------------------------------------------- 23
Setting Up the Password (
pass
) ------------------------------------------- 24
Locking the Meter ------------------------------------------------------------ 24
Unlocking the Meter---------------------------------------------------------- 24
OPERATION----------------------------------------------------------------26
Front Panel Buttons Operation -------------------------------------------- 26
Maximum/Minimum Readings---------------------------------------------- 27
MOUNTING DIMENSIONS----------------------------------------------28
TROUBLESHOOTING----------------------------------------------------29
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
4
Troubleshooting Tips --------------------------------------------------------- 29
QUICK USER INTERFACE REFERENCE GUIDE----------------30
EU DECLARATION OF CONFORMITY -----------------------------31
Table of Figures
Figure 1. Panel Cutout and Mounting.................................................9
Figure 2. Connector Labeling - Meter with 24 V Supply..................10
Figure 3. Power Connections............................................................10
Figure 4. Transmitter Powered by Ext. Supply or Self-Powered....11
Figure 5. Transmitters Powered by Internal Supply (Optional)......11
Figure 6. Voltage Input Connections................................................12
Figure 7. Meter Dimensions - Side View...........................................28
Figure 8. Case Dimensions - Top View.............................................28
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
5
SPECIFICATIONS
Except where noted all specifications apply to operation at +25°C.
General
DISPLAY 0.56" (14 mm) high, red LED
Four digits (-1999 to 9999), automatic lead zero blanking.
DISPLAY
UPDATE RATE 5/second
OVERRANGE Display flashes 9999
UNDERRANGE Display flashes -1999
PROGRAMMING
METHODS Four front panel buttons
RECALIBRATION All ranges are calibrated at the factory.
Recalibration is recommended at least every 12 months.
MAX/MIN
DISPLAY Max/min readings reached by the process are stored until reset by the user or until power to the meter is turned off.
PASSWORD Programmable password restricts modification of
programmed settings.
NON-VOLATILE
MEMORY All programmed settings are stored in non-volatile memory for a minimum of ten years if power is lost.
POWER
OPTIONS 85-265 VAC, 50/60 Hz; 90-265 VDC, 20 W max or 12-36 VDC, 12-24 VAC, 6 W max
FUSE Required fuse: UL Recognized, 5 A max, slow blow
Up to 6 meters may share one 5 A fuse
ISOLATED
TRANSMITTER
POWER SUPPLY
P+, P- terminals: 24 VDC ±10% @ 200 mA max
NORMAL MODE
REJECTION 64 dB at 50/60 Hz
ISOLATION 4 kV input-to-power line
500 V input-to-24 V supply
OVERVOLTAGE
CATEGORY Installation Overvoltage Category II: Local level with smaller transient overvoltages than Instal-
lation Overvoltage Category III.
ENVIRONMENTAL Operating temperature range: 0 to 65°C
Storage temperature range: -40 to 85°C
Relative humidity: 0 to 90% non-condensing
CONNECTIONS Removable screw terminal blocks accept 12 to 22 AWG
wire, RJ11 for factory use only.
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
6
ENCLOSURE 1/8 DIN, high impact plastic, UL 94V-0, color: gray
MOUNTING 1/8 DIN panel cutout required. Two panel mounting
bracket assemblies provided
TIGHTENING
TORQUE Screw terminal connectors: 5 lb-in (0.56 Nm)
OVERALL
DIMENSIONS 2.45" x 4.68" x 4.19" (62 mm x 119 mm x 106 mm) (H x W x D)
WEIGHT 8.5 oz (241 g)
WARRANTY 1 year parts & labor
EXTENDED
WARRANTY 1 or 2 years, refer to the Price List for details.
Process Input
INPUTS Field selectable:
0-20, 4-20 mA, 0-5, 1-5, 0-10 V, or ±10 V
ACCURACY ±0.05% FS ±1 count
FUNCTION Linear
TEMPERATURE
DRIFT 50 PPM/°C from 0 to 65°C ambient
DECIMAL POINT Up to three decimal places:
d.ddd, dd.dd, ddd.d,or dddd
CALIBRATION
RANGE An Error message will appear if input 1 and input 2 signals are too close together.
Input
Range Minimum Span Input 1 & Input 2
4-20 mA 0.40 mA
±10 V 0.20 V
INPUT
IMPEDANCE Voltage ranges: greater than 1 MΩ
Current ranges: 50 - 100 Ω(depending on resettable fuse impedance)
INPUT
OVERLOAD Current input protected by resettable fuse. Fuse resets automatically after fault is removed.
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
7
COMPLIANCE INFORMATION
Safety
UL LISTED USA and Canada
UL 508 Industrial Control Equipment
UL FILE NUMBER E160849
FRONT PANEL UL Type 4X, NEMA 4X, IP65; panel gasket provided
LOW VOLTAGE
DIRECTIVE EN 61010-1:2010 Safety requirements for measurement, control, and
laboratory use
Electromagnetic Compatibility
EMISSIONS EN 55011:2009+Al:2010
Group 1 Class A ISM emissions requirements
Radiated
Emissions Class A
AC Mains Con-
ducted Emissions Class A
IMMUNITY EN 61326-1:2013
Measurement, control, and laboratory equipment
EN 61000-6-2:2005
EMC heavy industrial generic immunity standard
RFI - Amplitude
Modulated 80 -1000 MHz 10 V/m 80% AM (1 kHz)
1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)
2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)
Electrical Fast
Transients ±2kV AC mains, ±1kV other
Electrostatic
Discharge ±4kV contact, ±8kV air
RFI - Conducted 10V, 0.15-80 MHz, 1kHz 80% AM
AC Surge ±2kV Common, ±1kV Differential
Surge 1KV (CM)
Power-Frequency
Magnetic Field 30 A/m 70%V for 0.5 period
Voltage Dips 40%V for 5 & 50 periods
70%V for 25 periods
Voltage
Interruptions <5%V for 250 periods
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
8
Note:
Testing was conducted on PD603 meters installed through the co-
vers of grounded metal enclosures with cable shields grounded at
the point of entry representing installations designed to optimize
EMC performance.
SAFETY INFORMATION
CAUTION: Read complete
instructions prior to instal-
lation and operation of the
meter.
WARNING: Risk of
electric shock.
WARNING
Hazardous voltages exist within enclosure. Installation and service
should be performed only by trained service personnel.
!
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
9
INSTALLATION
There is no need to remove the meter from its case to com-
plete the installation, wiring, and setup of the meter.
Unpacking
Remove the meter from box. Inspect the packaging and con-
tents for damage. Report damages, if any, to the carrier.
If any part is missing or the meter malfunctions, please contact
your supplier or the factory for assistance.
Panel Mounting
•Prepare a standard 1/8 DIN panel cutout – 3.622" x 1.772" (92 mm
x 45 mm). Refer to Mounting Dimensions, page 28 for more details.
•Clearance: allow at least 4" (102 mm) behind the panel for wiring.
•Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).
Recommended minimum panel thickness to maintain Type 4X
rating: 0.06" (1.5 mm) steel panel, 0.16" (4.1 mm) plastic panel.
•Remove the two mounting brackets provided with the meter (back-off
the two screws so that there is ¼" (6.4 mm) or less through the
bracket. Slide the bracket toward the front of the case and remove).
•Insert meter into the panel cutout.
•Install mounting brackets and tighten the screws against the panel.
To achieve a proper seal, tighten the mounting bracket screws
evenly until meter is snug to the panel along its short side. DO NOT
OVER TIGHTEN, as the rear of the panel may be damaged.
Figure 1. Panel Cutout and Mounting
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
10
Connections
All connections are made to removable screw terminal connectors
located at the rear of the meter.
Use copper wire with 60°C or 60/75°C insulation
for all line voltage connections. Observe all safety
regulations. Electrical wiring should be performed
in accordance with all applicable national, state,
and local codes to prevent damage to the meter
and ensure personnel safety.
Connector Labeling
The connectors label, affixed to the meter, shows the location of the
connectors available with requested configuration.
Figure 2. Connector Labeling - Meter with 24 V Supply
Power Connections
Power connections are made to a two-terminal connector labeled
POWER on Figure 2. The meter will operate regardless of DC polarity
connection. The + and - symbols are only a suggested wiring convention.
Figure 3. Power Connections
24V OUT
DW1911
POWER
XXV+ mA+ COM Factory
Use
Only
3412 5
2121
P+ P-
+-
SIGNAL
12
AC or DC
POWER
Required External Fuse:
5 A max, Slow Blow
POWER CONNECTOR
+-
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
11
Signal Connections
Signal connections are made to a five-terminal connector labeled
SIGNAL on Figure 2. The COM (common) terminal is the return for all
types of input signals.
Current and Voltage Connections
The following figures show examples for current and voltage connections.
There are no switches or jumpers to set up for current and voltage inputs.
Setup and programming is performed through the front panel buttons.
Figure 4. Transmitter Powered by Ext. Supply or Self-Powered
Figure 5. Transmitters Powered by Internal Supply (Optional)
The current input is protected against current overload by a resettable
fuse. The display may or may not show a fault condition depending on
the nature of the overload.
The fuse limits the current to a safe level when it detects a fault condi-
tion, and automatically resets itself when the fault condition is removed.
COMmA+
21 354
V+ X
X
External
Power
Supply
2-Wire
4-20 mA
Transmitter
-+ +-
SIGNAL CONNECTOR COM SIGNAL CONNECTOR
mA+
21 354
V+ X
X
2-Wire 4-20 mA
Self-Powered
Transmitter
-+
COM
SIGNAL CONNECTOR
mA+
21 354
V+ X
X
2-Wire
4-20 mA
Transmitter
-+
P+ P-
21
24V OUT COM
SIGNAL CONNECTOR
mA+
21 354
V+ X
X
3-Wire
4-20 mA
Transmitter
Signal +
21
24V OUT
-
P+ P-
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
12
Figure 6. Voltage Input Connections
The meter is capable of accepting any voltage from -10 VDC to +10 VDC.
SIGNAL CONNECTOR
21 354
Voltage
Signal
+-
COMmA+V+ XXCOM
SIGNAL CONNECTOR
mA+
21 354
V+ XX
3-Wire
Voltage
Transducer
Signal +
21
24V OUT
-
P+ P-
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
13
SETUP AND PROGRAMMING
•There is no need to recalibrate the meter
when first received from the factory.
•The meter is factory calibrated prior to ship-
ment, for all input types, in milliamps and
volts. The calibration equipment is certified to
NIST standards.
Overview
There are no jumpers involved in the setup process of the meter. The
switch, located between the SIGNAL and the RJ11 connectors is not
used with the PD603 model. Setup and programming is done through
the front panel buttons.
After power and signal connections have been completed and verified,
apply power to the meter.
For
Quick User Interface Reference Guide
go to page 30
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
14
Front Panel Buttons and Status LED Indicators
Button
Symbol Description
Menu
Right arrow/Reset
Up arrow/Max
Enter/Ack
•Press the Menu button to enter or exit the Programming Mode at
any time.
•Press the Right arrow button to move to the next digit during digit
programming.
•Press the Up arrow button to scroll through the menus, decimal
point, or to increment the value of a digit.
•Press the Enter/Ack button to access a menu or to accept a setting.
9.603
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
15
Display Functions and Messages
The meter displays various functions and messages during setup/pro-
gramming and operation. The following table shows the displayed func-
tions and messages with their action/setting description.
Display Parameter Action/Setting
setu Setup Enter Setup menu
inpt Input Enter Input menu
4-20 4-20 mA Set meter for 4-20 mA input
0-10 0-10 VDC Set meter for ±10 VDC input
dec.p Decimal point Set decimal point for process inputs
prog Program Enter the Program menu
scal Scale Enter the Scale menu
Cal Calibrate Enter the Calibrate menu
inp1 Input 1 Calibrate input 1 signal or program input 1
value
dis1 Display 1 Program display 1 value
inp2 Input 2 Calibrate input 2 signal or program input 2
value
dis2 Display 2 Program display 2 value
err Error Error, calibration not successful, check signal
pass Password Enter the Password menu
unlC Unlocked Program password to lock meter
loCd Locked Enter password to unlock meter
9999
-1999 Flashing display Overrange condition
Underrange condition
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
16
Main Menu
The main menu consists of the following functions: Setup, Program, and
Password.
•Press Menu button to enter Programming Mode then press Up ar-
row button to scroll main menu.
•Press Menu, at any time, to exit and return to Run Mode. Changes
made to settings prior to pressing Enter/Ack are not saved.
•Changes to the settings are saved to memory only after pressing
Enter/Ack.
•The display moves to the next menu every time a setting is ac-
cepted by pressing Enter/Ack.
9603 setu prog pass
Run
Mode
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
17
Setting Numeric Values
The numeric values are set using the Right and Up arrow buttons.
Press Right arrow to select next digit and Up arrow to increment digit
value.
The digit being changed is displayed brighter than the rest.
Press the Enter/Ack button, at any time, to accept a setting or Menu
button to exit without saving changes.
The decimal point is set using the Up arrow button in the Setup-decimal
point menu.
04.00 04.00 05.00
Increment Digit
Value
Next
Setting
Select Next Digit Accept Setting
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
18
Setting Up the Meter (
setu
)
The Setup menu is used to select:
1. Input signal the meter will accept
2. Decimal point position
Press the Enter/Ack button to access any menu or press Up arrow but-
ton to scroll through choices. Press the Menu button to exit at any time.
Setting the Input Signal (
inpt
)
Enter the Input menu to set up the meter to display current (4-20) or
voltage (0-10) inputs.
The voltage input is capable of accepting any signal from -10 to +10
VDC. Select voltage input to accept 0-5, 1-5, 0-10, or ±10 VDC signals.
The current input is capable of accepting any signal from -20 to 20 mA.
Select current input to accept 0-20 or 4-20 mA signals.
setu inpt dec.p
inpt
4-20 0-10
Press Enter/Ack to
Make Selections
Press Up Arrow
to Scroll Through
Choices
Press Menu to
Exit at any Time
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
19
Setting the Decimal Point (
dec.p
)
Decimal point may be set with up to three decimal places or with no
decimal point at all.
Pressing the Up arrow moves the decimal point one place to the right
until no decimal point is displayed, then it moves to the leftmost position.
dec.p
dddd
Next
Select Decimal
Point
Previous
www. .com [e-mail]1.800.561.8187

Sabre P Model PD603 Process Meter Instruction Manual
20
Programming the Meter (
prog
)
It is very important to read the following information, before proceeding
to program the meter:
•There is no need to recalibrate the meter when first received from
the factory.
•The meter is factory calibrated prior to shipment, for all input
types, in milliamps and volts. The calibration equipment is certified
to NIST standards.
•Use the Scale menu to scale process inputs (e.g. 4-20 mA). A cali-
brated signal source is not needed to scale the meter.
The Program menu contains the Calibrate and the Scale menus.
Process inputs may be calibrated or scaled to any display within the
range of the meter.
prog Cal scal
www. .com [e-mail]1.800.561.8187