PREMIER POLYSTEEL 950-501 User manual

950-501
Part
No.
Description Qty.
642-A15 8’ Champion Accessible Top 1
622-013 6’ Champion Seat/Back 2
634-010 Free Standing Table Stand 2
634-013A Table Brace w/Umbrella Hole 2
516-058 3/8” X 1-1/2” SS Hex Bolt 16
516-028 3/8” SS Nylock Nut 16
516-023 3/8” SS Flat Washer 32
Assembly Instructions
1 Drill out holes on the Table Top, Seats, Stands and Braces with a 7/16” dia. drill.
2 Attach the Stands to the Table Top loosely using the 3/8” x 1-1/2” SS Bolts. (See photo above
right)
3 Attach the Seats to the Stands loosely using the 3/8” x 1-1/2” SS Bolts.
4 Attach Braces to the Stands and Table Top loosely using the 3/8” x 1-1/2” SS Bolts. (See photo
above right)
5 Tighten all bolts.
Periodic check of bolt tightness recommended.
30
20
96
68 3
16
517
8
950-501 8FT CHAMPION
FREESTANDING TABLE
ACCESSIBLE
22
421
2
• Attach both legs to the inside of table
support bar
• Attach the straight end of each brace to
the table.
• Attach bent end of both braces to the
cross bar of each leg.

10"
30" 62 1/2"
72"
96"
31"
20"
69"
X.01
950-5P1
8' Champion Accessible Perforated Metal Table, Free Standing
SHEET 1 OF 2 REV.
A
SIZE

3
2
1
4
6
7
5
Assembly Instructions
1. Drill out holes.
2. Attach both legs to the inside of table support bar. (See view above)
3. Attach the seats to the legs.
4. Attach the straight end of each brace to the table. (See view above)
5. Attach bent end of both braces to the cross bar of each leg. (See view above)
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-AP5 8' Champion Accessible Table Top 1
2 622-P13 6 ' Champion Perf Seat/Back 2
3 634-010 FS Table Stand (10" Seats) 2
4 634-013A Table Brace W/Umbrella 2
5 516-058 3/8"x1-1/2" SS Hex Bolt 14
6 516-023 3/8" SS Flat Washer 28
7 516-028 3/8" SS Nylock Nut 14
X.01
950-5P1
8' Champion Accessible Perforated Metal Table, Free Standing
SHEET 2 OF 2 REV.
A
SIZE

Part No. Description Qty.
642-A15 Champion Accessible Table Top
8’
1
622-013 Champion Seat/Back 6’ 2
632-200 Table Pedestal Direct Bury 2
516-058 3/8” X 1-1/2” SS Hex Bolt 12
516-028 3/8” SS Nylock Nut 12
516-023 3/8” SS Flat Washer 24
950-502
1 Drill 2 holes in ground per the above drawing.
2 Place the pedestals in the holes.
3 Drill plastic out of the mounting holes on the pedestals, top and seats using a 7/16” dia. drill bit.
4 Fasten the table top to the pedestals, support and level table top. Check height.
5 Fasten the seats to the pedestals, support and level seats. Check height.
6 When the seats and top are level and secured fill the holes with concrete to about 2” below
ground level.
Periodic check of bolt tightness recommended.

72"
10"
30"
6 1/4"
62 1/2"
96"
31"
19 1/2"
Drill plastic out of the mounting holes on the pedestals, top and seats using a 7/16” dia. drill bit. 1.
Fasten the table top and seats to the pedestals, installing the pedestal on the inside of the table 2.
and seat mounting bar.
Position the table and seats and anchor them to the floor. 3.
X.01
950-505
8' Accessible Multi-Pedestal Surface Mount
SHEET 1 OF 2 REV.
A
SIZE

4
2
1
3
5
7
6
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-A15 8' Accessible Table Top Expanded 1
2 622-013 Champion Seat/Back 6' 2
3 633-131 Table Pedestal Stand (Surface Mount) 2
4 633-141 Seat Pedestal Stand (Surface Mount) 4
5 516-058 3/8"x1-1/2" SS Hex Bolt 12
6 516-028 3/8" SS Nylock Nut 12
7 516-023 3/8" SS Flat Washer 24
X.01
950-505
8' Accessible Multi-Pedestal Surface Mount
SHEET 2 OF 2 REV.
A
SIZE

76"
73 1/2"
40"
16 1/8"
20"
30"
X.01
927-101
SHEET 1 OF 2 REV.
A
SIZE

1
4
2
5
3
6
7
8
1. With table top upside down bolt 2 opposing legs on to top. Do not tighten the bolts now.
2. Attach “x” shaped leg brace to the 2 legs.
3. Attach the other 6 legs fastening to the “x” shaped leg brace as you go.
4. Attach seats to other end of leg. The vertical portion of the angle iron leg top bolts flush with
the seat support bar.
5. Flip the table right side up, level the top and seats, and tighten all of the bolts.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-115 4x5 Accessible table Top 1
2 634-111 Sq./Rnd Table Free Standing Leg 6
3 634-112 3 Seat Leg for Sq/Round Table 2
4 622-019 40" Champion Seat 3
5 634-119 Sq./Rnd Table Leg Support Bracket 1
6 516-058 3/8"x1-1/2" SS Hex Bolt 28
7 516-023 3/8" SS Flat Washer 56
8 516-028 3/8" SS Nylock Nut 28
X.01
927-101
SHEET 2 OF 2 REV.
A
SIZE