PREMIER POLYSTEEL 955-101 User manual

79"
20"
30"
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-R11 4' Round Table Top 1
2 622-R11 Champion Round Table Seat 4
3 634-119 Sq./Rnd Table Leg Support Bracket 1
4 634-111 Sq./Rnd Table Free Standing Leg 8
5 516-028 3/8" SS Nylock Nut 32
6 516-058 3/8"x1-1/2" SS Hex Bolt 32
7 516-023 3/8" SS Flat Washer 64
X.01
955-101
Champion 48" Round FS Table
SHEET 1 OF 2 REV.
A
SIZE

12
4 3
Fig. 2
7
5
6
Fig. 1
Opposing legs
1. With table top upside down bolt 2 opposing legs on to top. As shown in Fig. 1. Do not
tighten the bolts now.
2. Attach “x” shaped leg brace to the 2 legs.
3. Attach the other 6 legs fastening to the “x” shaped leg brace as you go.
4. Attach seats to other end of leg. The vertical portion of the angle iron leg top bolts flush
with the seat support bar.
5. Flip the table right side up, level the top and seats, and tighten all of the bolts.
X.01
955-101
Champion 48" Round FS Table
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a chemical know to the State of California
to cause cancer and birth defects or other reproductive harm.

Part No. Description Qty.
642-111A/642-R11A 48” Champion Sq/Rnd Table
Top WO/ Umbrella Hole
1
622-019/622-R11 40” Champion Seat 4
632-101 Center Pedestal Post 1
632-102 Table Top Support 1
632-103 Seat Arms 2
632-104 Seat Supports 4
632-105 Seat Arm for 4’ Sq/Rd 1 Ped
Tbl
2
926-108/955-108
632-102632-104
632-101
632-105
The Table Top and Seats are not shown.
Periodic check of bolt tightness recommended.
632-103

926-108 Single Pedestal Direct Bury Square Ta-
ble
955-108 Single Pedestal Direct Bury Round Table
1 Bore a 12-14” diameter hole 36” into the ground.
2 Place 4-6” of pea rock in hole.
3 Place center pedestal post into the hole.
4 Drill out all holes with a 7/16” drill bit. Use a 1/2” drill bit for seat arm end plate holes
and center pedestal post holes at their union.
5 Bolt the support arms on to the center pedestal post using 1/2”x9” stainless steel hex
bolts.
6 Bolt seat supports on to the seat arms using 3/8”x2-1/2” stainless steel hex bolts.
7 Bolt table top support on to the center pedestal post using 3/8”x2-1/2” stainless steel hex
bolts.
8 Bolt the table top on to the table top support using 3/8”x1-1/2” stainless steel hex bolts.
9 Bolt the seats on to the seat supports using 3/8”x1-1/2” stainless steel hex bolts.
10 Level table and adjust to desired height. Recommended height is 20” from the ground to
the top of the seats.
11 Fill hole with concrete no higher than ground level.
Periodic check of bolt tightness recommended.
In Accordance to California law: WARNING This product contains a chemical know to the State of California to
cause cancer and birth defects or other reproductive harm.