PREMIER POLYSTEEL 908-B81T User manual

R30"
41 1/2"
X.01
908-B81T
Premier Polysteel Bar Height Table, 30" Dia. Expanded Metal Top
SHEET 1 OF 2 REV.
A
SIZE

2
3
5
6
1
45
65
Assemble the table upside down. Protect the Table top from scratches by placing cardboard 1.
between it and the concrete floor.
Drill out holes in the Table Top, Legs and Leg Brace using a 7/16" dia. drill bit. 2.
Attach the legs to the Table Top with a bolt, 2 washers & locknut.
Do not tighten the bolts 3.
and locknuts at this time.
Attach the Leg Brace with flat top towards the Table Top. Use a locknut and washer on each 4.
threaded stud.
Do not tighten at this time.
Set table upright on a level surface and tighten all the hardware. Make sure that the Table 5.
Top is level as you tighten the hardware.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-B30 30" Expanded Table Top 1
2 634-541 Bar Table Leg 4
3 634-542 Leg Brace 1
4 516-058 3/8"x1-1/2" SS Hex Bolt 8
5 516-023 3/8" SS Flat Washer 20
6 516-028 3/8" SS Nylock Nut 12
X.01
908-B81T
Premier Polysteel Bar Height Table, 30" Dia. Expanded Metal Top
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a chemical known to the State of
California to cause cancer and birth defects or other reproductive harm.
Periodic check of bolt tightness recommended.

30"
41 1/4"
1
2
3
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-B35 30" Round Table Top Laser 1
2 634-541 Bar Table Leg 4
3 634-542 Leg Brace 1
4 516-058 3/8"x1-1/2" SS Hex Bolt 8
5 516-023 3/8" SS Flat Washer 20
6 516-028 3/8" SS Nylock Nut 12
X.01
958-B81T
Premier Polysteel 30" Laser Bar Height Table
SHEET 1 OF 2 REV.
A
SIZE
Periodic checking of bolt tightness is recommended.

19 1/2"
27"
29 11/16"
45 1/4"
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 639-501 Bar Height Chair Stand 1
2 625-009 Laser Deck Seat 1
3 516-023 3/8" SS Flat Washer 8
4 516-067 3/8"x2-1/2" SS Btn Skt Cap Scr. 4
5 516-028 3/8" SS Nylock Nut 4
6 516-061 Leg Glide 4
X.01
939-B11
Laser Bar Height Chair
SHEET 1 OF 2 REV.
A
SIZE

2
1
4
3
5
6
If the Leg Glides are not installed, screw them into the bottom of the stands first. 1.
Drill the plastic out of the slots on both sides of the seat and the tubes at the top of the 2.
stand using a 7/16" drill bit.
Attach the seat to the stand using the Button Socket Cap Screws, Washers, and 3.
Nylock Nuts. Do not tighten the nuts until all four of the Button Socket Cap Screws
have been installed.
Tighten all of the Nuts until the washers are pressed into the plastic coating to the 4.
thickness of the Washer.
X.01
939-B11
Laser Bar Height Chair
SHEET 2 OF 2 REV.
A
SIZE
In accordance to California law: WARNING - This product contains a chemical known to the State of
California to cause cancer and birth defects or other reproductive harm.
Periodic checking of bolt tightness is recommended.

19 1/2"
27"
29 11/16"
45 1/4"
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 639-501 Bar Height Chair Stand 1
2 623-007 Expanded Deck Seat 1
3 516-023 3/8" SS Flat Washer 8
4 516-067 3/8"x2-1/2" SS Btn Skt Cap Scr. 4
5 516-028 3/8" SS Nylock Nut 4
6 516-061 Leg Glide 4
X.01
939-B31
Expanded Bar Height Chair
SHEET 1 OF 2 REV.
A
SIZE

2
1
4
3
5
6
If the Leg Glides are not installed, screw them into the bottom of the stands first. 1.
Drill the plastic out of the slots on both sides of the seat and the tubes at the top of the 2.
stand using a 7/16" drill bit.
Attach the seat to the stand using the Button Socket Cap Screws, Washers, and 3.
Nylock Nuts. Do not tighten the nuts until all four of the Button Socket Cap Screws
have been installed.
Tighten all of the Nuts until the washers are pressed into the plastic coating to the 4.
thickness of the Washer.
X.01
939-B31
Expanded Bar Height Chair
SHEET 2 OF 2 REV.
A
SIZE
In accordance to California law: WARNING - This product contains a chemical known to the State of California
to cause cancer and birth defects or other reproductive harm.
Periodic checking of bolt tightness is recommended.