Pride Mobility JAZZY 1121 User manual

Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
Quality Control - Jazzy 1121
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
*INFMANU1935* Product Serial #
JAZZY 1121
32 Wedgwood Road • Bicester, Oxon OX26 4UL

Authorised Pride Dealer: __________________________________________________________________
Address: _______________________________________________________________________________
Phone Number:__________________________________________________________________________
Purchase Date: __________________________________________________________________________
SAFETY GUIDELINES
Copyright © 2012
Pride Mobility Products Ltd.
INFMANU1935/Rev G/May 2012
NOTE: This owner’s manual is compiled from the latest specifications and product information available at
the time of publication. We reserve the right to make changes as they become necessary. Any changes to our
products may cause slight variations between the illustrations and explanations in this manual and the product
you have purchased. The latest/current version of this manual is available on our website.
The symbols below are used throughout this owner's manual and on the power chair to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated
procedures can cause either personal injury, component damage or malfunction. On the product,
this icon is represented as a black symbol on a yellow triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause personal injury and/or equipment damage. On the product, this icon is
represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at any time
or in any circumstances. Performing a prohibited action can cause personal injury and/or
equipment damage. On the product, this icon is represented as a black symbol with a red circle
and red slash.
WARNING! An authorised Pride Dealer or a qualified technician must perform the initial setup of
this power chair and must perform all of the procedures in this manual.
INTENDED USE
The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated
position that have the capability of operating a powered wheelchair.
Quick Reference Information

Jazzy 1121 3www.pridemobility.com
I. INTRODUCTION .................................................................................................................................. 4
II. SAFETY ................................................................................................................................................... 5
III. YOUR POWER CHAIR ...................................................................................................................... 13
IV. ASSEMBLY .......................................................................................................................................... 17
V. COMFORT ADJUSTMENTS ......................................................................................................... 21
VI. BATTERIES AND CHARGING ..................................................................................................... 32
VII. CARE AND MAINTENANCE ......................................................................................................... 36
VIII. WARRANTY ........................................................................................................................................ 41
APPENDIX I - SPECIFICATIONS ........................................................................................................ 42
CONTENTS

Jazzy 11214 www.pridemobility.com
I. INTRODUCTION
SAFETY
WELCOME to Pride Mobility Products (Pride). The power chair you have purchased combines state-of-the-art
components with safety, comfort and styling in mind. We are confident that these design features will provide you
with the conveniences you expect during your daily activities. Once you understand how to safely operate and
care for your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings and notes in this manual before attempting to operate your power chair
for the first time. You must also read all instructions, warnings and notes contained in any supplemental instruc-
tional booklets for the controller, front riggings and/or seating system that accompanied your power chair before
initial operation. Your safety depends upon you, as well as your dealer, carer or healthcare professional in using
good judgement.
If there is any information in this manual which you do not understand or if you require additional assistance for
setup or operation, please contact your authorised Pride Dealer. Failure to follow the instructions in this manual
and those located on your power chair can lead to personal injury and/or damage to the power chair,
including voiding the warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter or modify this product or remove
or render inoperable or unsafe any guards, shields or other safety features of this product; fail, refuse or neglect
to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact your authorised Pride Dealer immediately.
Where damage has occurred during transport, either to the packaging or content, please contact the delivery com-
pany responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments and suggestions about this manual. We would also like to hear about the
safety and reliability of your new power chair and about the service you received from your authorised Pride Dealer.
Please notify us of any change of address, so we can keep you apprised of important information about safety,
new products and new options that can increase your ability to use and enjoy your power chair. Please feel free to
contact us at the address below:
Pride Mobility Products Ltd.
32 Wedgwood Road
Bicester, Oxon OX26 4UL
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.

Jazzy 1121 5www.pridemobility.com
II. SAFETY
GENERAL GUIDELINES
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final
selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power
chair user, who is capable of making such a decision and his/her healthcare professional (i.e., medical doctor,
physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the
power chair to the user and has assisted the prescribing healthcare professional and/or the authorised Pride Dealer
in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice
operating the power chair in the presence of a trained attendant. A trained attendant can be defined as a family
member or care professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you
will need some practice. Simply take your time and you will soon be in full and confident control as you manoeu-
vre through doorways, on and off of lifts, up and down ramps and over moderate terrain.
Below are some precautions, tips and other safety considerations that will help the user become accustomed to
operating the power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of
accessories is available from your authorised Pride Dealer to further customise your power chair to better suit your
needs and/or preferences. However, under no circumstances should you modify, add, remove or disable any fea-
ture, part or function of your power chair.
WARNING! Do not modify your power chair in any way not authorised by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
Check for proper tyre inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on
each tyre if equipped with pneumatic tyres.
Check all electrical connections. Make sure they are tight and not corroded.
Check all controller connections to the electronics tray. Make sure they are secured properly.
Check the brakes. See VII. “Care and Maintenance.”
Check battery charge. See VI. “Batteries and Charging.”
Ensure the manual freewheel levers are in drive mode before sitting on the power chair.
NOTE: If you discover a problem, contact your authorised Pride Dealer for assistance.

Jazzy 11216 www.pridemobility.com
II. SAFETY
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories
mounted to the power chair.
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the
weight capacity voids your warranty. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the centre of gravity, resulting in a tip or a fall.
Tyre Inflation
If your power chair is equipped with pneumatic tyres, you should check or have the air pressure checked regularly.
Proper inflation pressures will prolong the life of your tyres and help ensure the smooth operation of your power chair.
WARNING! It is important that the psi/bar/kPa air pressure rating indicated on the tyre be
maintained in pneumatic tyres at all times. Do not underinflate or overinflate your tyres. Low
pressure may result in loss of control, and overinflated tyres may burst. Failure to maintain the
psi/bar/kPa air pressure rating indicated on the pneumatic tyres at all times may result in tyre
and/or wheel failure.
WARNING! Inflate your power chair drive tyres from a regulated air source with an available
pressure gauge. Inflating your tyres from an unregulated air source could overinflate them,
resulting in a burst tyre.
NOTE: If the tyres on your power chair list the psi rating only, use the following conversion formulas to find
the bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.
Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on
your power chair.
Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power
chair’s rear wheels will follow a wide arc, not cut the corner short and not bump into or get hung up on any
railing corners.
When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure
a safely controlled descent.
Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accel-
erate cautiously. When driving down an incline, set your power chair to the slowest setting and drive in the forward
direction only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come
to a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the power chair in freewheel
mode while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your power chair straight up the incline. This greatly reduces the possibility of a
tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiate
inclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seat
in a reclined position unless an attendant is present to help stabilise the chair. Failure to heed
may result in the power chair tipping over.

Jazzy 1121 7www.pridemobility.com
II. SAFETY
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass or wet leaves).
WARNING! Even though your power chair is capable of climbing slopes greater than those
illustrated in figure 1, do not, under any circumstances, exceed the incline guidelines or any other
specifications presented in this manual. Doing so could cause instability in your power chair.
WARNING! Traveling down inclines rearward may have an adverse effect on the stability of the power
chair. Although the power chair is in compliance with all ISO rearward static and dynamic stability
testing, Pride strongly recommends that inclines be negotiated in the forward-facing position to
reduce the possibility of a tip or fall. In the case of wheelchair accessible vehicles, the suitability of
the vehicle-mounted ramp should be determined before using your power chair with the WAV.
Pride recommends that the maximum slope of an incline you attempt to safely ascend or descend on your power
chair does not exceed 10.5% (6°). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 10.5% (6°) may put your power
chair in an unstable position and cause it to tip.
Figure 1. Maximum Safe Angle (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual manoeuvreability by a trained
attendant. For more information about how to place your power chair into and out of freewheel mode, see III.
“Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline or decline. This
could cause the chair to roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
 Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the centre/stop position.
Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop or when
power is removed from the system for any reason.
Cornering Information
While your power chair is equipped with front anti-tip wheels and rear castor wheels, excessively high cornering
speeds can still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not
limited to: cornering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road
surfaces, riding from an area of low traction to an area of high traction (such as passing from a grassy area to a
paved area—especially at high speed while turning) and abrupt directional changes. High cornering speeds are
not recommended. If you feel that you may tip over in a corner, reduce your speed and steering angle (i.e., lessen
the sharpness of the turn) to prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable centre of gravity.
This greatly reduces the possibility of a tip or fall.

Jazzy 11218 www.pridemobility.com
II. SAFETY
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces
composed of concrete, blacktop or tarmac. However, Pride recognises that there will be times when you will
encounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,
grass and gravel. Feel free to use your power chair safely on lawns and in park areas.
Avoid driving on uneven terrain and/or soft surfaces.
Avoid tall grass that can entangle the running gear.
Avoid loosely packed gravel and sand.
Do not use your power chair in fresh or salt water.
Do not use your power chair at the edge of a stream, lake, or ocean.
If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly
caught up in rain, snow, severe cold or heat while operating your power chair proceed to shelter at the earliest
opportunity. Thoroughly dry your power chair before storing, charging or operating your power chair.
WARNING! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces can
have an adverse affect on the electrical system. Maintain and store your power chair in a dry
and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the power chair, possibly resulting in skin irritation.
Exercise caution when using your power chair in extremely hot or cold conditions or when
exposing your power chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Kerbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (kerbs,
porches, stairs, etc.). The correct method for approaching a kerb is illustrated in figure 2.
To navigate up over a kerb or stationary obstacle:
1. Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle. See figure 2.
2. Increase the forward speed just before the front wheels come in contact with the obstacle.
3. Reduce the forward speed only after the rear wheels have cleared the obstacle.
Figure 3. Incorrect Kerb Approach
Figure 2. Correct Kerb Approach

Jazzy 1121 9www.pridemobility.com
II. SAFETY
To navigate down a kerb or stationary obstacle:
1. Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle. See figure 2.
2. Reduce the forward speed just before the front wheels come in contact with the obstacle.
3. Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a level surface.
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 7.62 cm (3 in.) unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed rearward down any step, kerb or
other obstacle. This may cause the power chair to tip.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use a lift.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
Determine if the door opens toward or away from you.
Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently
and slowly rearward to pull the door open.
Lifts
Modern lifts have a door edge safety mechanism that, when pushed, reopens the lift door(s).
If you are in the doorway of a lift when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
Use care that handbags, packages or power chair accessories do not become caught in lift doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in
transportation. Pride recommends that you closely review the instructions, specifications and safety information
set forth by the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any type of
lift/elevation product. Your power chair was not designed with such use in mind and any damage
or injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The
power chair should be stowed in the boot of a car or in the back of a truck or van with batteries removed and/or
properly secured. In addition, all removable power chair parts, including the armrests, seat, front riggings, con-
troller and shrouds should be removed and/or properly secured during motor vehicle transport. If your power chair
is equipped with a transit securement system, refer to IV. “Assembly” and the supplement provided with your
power chair for additional information regarding power chair transport in a motor vehicle.
WARNING! Pride does not recommend using the power chair as a seat in a motor vehicle. The
power chair user should transfer into the vehicle seat and use the vehicle-installed belt restraint
system if and whenever feasible. If your power chair is equipped with a manufacturer-installed
transit securement system, please refer to the supplemental safety information provided with
your power chair.
WARNING! Ensure power chairs equipped with a transit securement system are properly
secured to the motor vehicle during transport. Power chairs that are not properly secured can
become a hazard to the user and to other vehicle passengers in the event of a crash, sudden
stopping or swerving, as the power chair could tip or slide out of place.
WARNING! Always be sure your power chair and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps should
be installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.

Jazzy 112110 www.pridemobility.com
II. SAFETY
Positioning Belts
Your Quantum Rehab Dealer, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely. The positioning belt is not designed
for use as a restraining device in a motor vehicle. You should be properly belted into seats approved by the vehicle
manufacturer with your power chair properly stowed for vehicle transport or secured using an optional transit
securement system.
Positioning belts should be installed as detailed in this manual. See V. “Comfort Adjustments.” Once installed,
the belt should be placed across the pelvis as determined by your healthcare provider. Anchor points of the posi-
tioning belts should be located so that a projected side-view angle of the pelvis is between 45°-75° of horizontal
depending on the user’s weight, posture and seat cushion thickness.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should
be properly belted into seats approved by the vehicle manufacturer. If your power chair is
equipped with a manufacturer-installed transit securement system, please refer to the
supplemental safety information provided with your power chair.
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For
more information about your power chair’s batteries, see VI. “Batteries and Charging.”
MANDATORY! Battery posts, terminals and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen battery.
Charging a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must be
connected to positive (+) battery terminals/posts. BLACK (-) cables must be connected to
negative (-) battery terminals/posts. Protective caps should be installed over all battery
terminals. REPLACE cables immediately if damaged.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including
the armrests, seat, front riggings, controller and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This will
also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.
Reaching and Bending
Never reach, lean or bend while driving your power chair. If it is absolutely necessary to reach, lean or bend while
seated on your power chair, it is important to maintain a stable centre of gravity and keep the power chair from
tipping. Pride recommends that the power chair user determine his/her personal limitations and practice bending
and reaching in the presence of a qualified healthcare professional.
WARNING! Do not bend, lean or reach for objects if you have to pick them up from the floor by
reaching down between your knees or if you have to reach over the back of the seat. Movements
such as these may change your centre of gravity and the weight distribution of the power chair.
This may cause your power chair to tip.

Jazzy 1121 11www.pridemobility.com
II. SAFETY
To eliminate the possibility of injury, Pride recommends that you or
a trained attendant perform the following tasks before attempting a
transfer:
Ensure your power chair is not in freewheel mode. See III. “Your
Power Chair.”
Turn the castor wheels toward the transfer destination to improve
power chair stability during transfer.
Make sure both armrests are flipped up or removed from your
power chair.
Flip up the foot platform or move the leg rests aside; this will help
to keep your feet from getting caught on the front rigging during
the transfer.
Reduce the distance between your power chair and the object you
are transferring onto. Figure 4. Ideal Transfer Position
WARNING! Before transferring, turn off the power to the controller to prevent unintended
movement.
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer.
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the power chair
to tip, resulting in a fall from the power chair.
WARNING! The controller and controller bracket are non-load bearing items on your power chair.
Do not use the controller or controller bracket for weight bearing purposes, such as transfers.
Such use may cause damage to these components, resulting in a fall from the power chair and
personal injury.
WARNING! Avoid putting all of your weight on the front riggings. Such use may cause the power
chair to tip.
User Positioning
Pride recommends that all users be seated in an upright position with their pelvis positioned as far rearward as
possible in the power chair seat. All users need to discuss pelvic positioning with their authorised Pride Dealer,
therapist(s) or healthcare professional to determine appropriate pelvic position when seated on the power chair
based on the user’s individual medical needs.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety
issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your
ability to operate your power chair in a safe manner.
WARNING! Keep your hands away from the tyres when driving. Be aware that loose fitting
clothing can become caught in drive tyres.
Transfers
Transferring onto and off of your power chair requires a good sense of balance. Always have an attendant or
healthcare professional present while learning to properly transfer yourself.

Jazzy 112112 www.pridemobility.com
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your
power chair, although the power chair has passed the necessary testing requirements for
cigarette smoking. You must adhere to the following safety guidelines if you decide to smoke
cigarettes while seated in your power chair.
 Do not leave lit cigarettes unattended.
 Keep ashtrays a safe distance from the seat cushions.
 Always make sure cigarettes are completely extinguished before disposal.
Flammability Precautions
WARNING! Even though the plastics on your power chair have passed the applicable
flammability standards, Pride recommends that you do not expose your power chair to open
flames.
WARNING! Replace worn or damaged upholstery immediately to reduce the risk of fire hazard.
WARNING! Be aware that washing of upholstered items may reduce the resistance to
flammability of the fabric.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-
way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless com-
puter links, microwave signals, paging transmitters and medium-range mobile transceivers used by emergency
vehicles. In some cases, these waves can cause unintended movement or damage to the control system. Every
electrically-powered mobility vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the
greater the protection against EMI. This product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, electricity generators or high
power sources and other types of radio transmitters may cause unintended movement of your
electrically-powered mobility vehicle due to EMI. Exercise caution when using any of these
items while operating your mobility vehicle and avoid coming into close proximity of radio and
TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility
vehicle can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in
any way not authorised by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, go to the Resource Centre on www.pridemobility.com. If unin-
tended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Contact Pride to
report the incident.
II. SAFETY

Jazzy 1121 13www.pridemobility.com
III. YOUR POWER CHAIR
THE JAZZY 1121
The power chair has two main assemblies: the seat and the power base. See figures 5 and 6. Typically, the seat
assembly includes the armrests, seatback and seat base. The power base assembly includes two motor/brake
assemblies, two drive wheels, two anti-tip wheels, two castor wheels, two batteries and wiring harnesses.
SEATBACK
ARMREST
CONTROLLER
(REMOTE PLUS
SHOWN)
BODY SHROUD
ANTI-TIP WHEELS
DRIVE WHEEL
CASTOR WHEEL
JOYSTICK
FRONT RIGGING
(FOOT PLATFORM
SHOWN)
SEAT BASE
SEAT ASSEMBLY
POWER BASE
ASSEMBLY
Figure 5. The Jazzy 1121

Jazzy 112114 www.pridemobility.com
III. YOUR POWER CHAIR
REAR SEAT RECEIVERS
FRONT SEAT
RECEIVERS
ONBOARD BATTERY
CHARGER (UNDERNEATH
ELECTRONICS TRAY)
MOTOR/BRAKE ASSEMBLY
ELECTRONICS TRAY
FREEWHEEL LEVER
(UNDERNEATH
ELECTRONICS
TRAY)
POWER MODULE
(LOCATED UNDER ELECTRONICS
TRAY)
Figure 6. The Jazzy 1121 Power Base
MAIN CIRCUIT BREAKER
AMMETER
CHARGER POWER LEAD RECEPTACLE
CHARGER FUSES (UNDER COVER)
CONTROLLER CONNECTOR (VSI SHOWN)
CHARGER INHIBIT CONNECTOR
Figure 7. The Jazzy 1121 Electronics Tray

Jazzy 1121 15www.pridemobility.com
III. YOUR POWER CHAIR
Electronics Tray
The electronics tray is located on the back of the power base. See figure 7. The ammeter, the charger power lead,
the main circuit breaker, the controller connector and the charger fuse are all located on the electronics tray.
Ammeter: The ammeter displays the charger’s current output in amps. See VI. “Batteries and Charging.”
Charger Power Lead Receptacle: This is where the charger power lead plugs into the power base.
Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batter-
ies and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent
damage to the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approximately
one minute. Next, push in the circuit breaker button, turn on the controller and continue normal operation. If the
main circuit breaker continues to trip repeatedly, contact your authorised Pride Dealer.
Controller Connector: This is where the controller connects to the power base. Each controller uses a different
type of harness. Regardless of which type of controller is used, the cable must be secured to the seat assembly and
not allowed to drag on the floor.
Charger Inhibit Connector: The charger inhibit enables the onboard charger to disable the controller during
charging. The charger inhibit connector is coded with coloured dots. The dots are positioned so that you can align
the flat side of the male connector with the flat side of the female connector before making the connection.
WARNING! Failure to properly align the connectors can result in damage to the controller, the
charger harness and the connectors.
Charger Fuse: The charger fuse protects the ammeter from current overload. There are three fuses on the elec-
tronics tray. The top one is the charger fuse. The bottom two are spares.
Power Actuator Connector and Lighting System Connector (VSI Only): This is where the power actuator
connects to the controller. Standard lighting systems have a single-pin connector. Full lighting systems with the
VSI controller use a 3-pin connector. Not shown.
Active-Trac Suspension
The Jazzy 1121 is equipped with Active-Trac Suspension (ATS). ATS is a suspension system designed to make
your power chair traverse different types of terrain and obstacles while maintaining smooth operation. With ATS,
the front anti-tip wheels work in conjunction with your motor suspension to help you manoeuvre over obstacles
in excess of 7.62 cm (3 in.) in height.
As the front anti-tip wheels come in contact with an obstacle, the front anti-tip wheel assembly is drawn upward.
At the same time, the motors are forced downward. This allows the motors to push the power chair over an
obstacle without the possibility of becoming “hung up.”
ATS also helps in day-to-day operating conditions. For instance, when you release the joystick, your power chair
begins to slow down. As the chair slows down, the front anti-tip wheels will automatically drop toward the ground.
This will reduce the forward tip that is typically encountered with centre-wheel drive chairs.

Jazzy 112116 www.pridemobility.com
III. YOUR POWER CHAIR
Manual Freewheel System
For your convenience, your power chair is equipped with a manual freewheel system. This system consists of one
or more freewheel levers which enable you to disengage the drive motors and manoeuvre the chair manually.
WARNING! Do not use your power chair while the drive motors are disengaged! Do not disengage
the drive motors when your power chair is on an incline, as the unit could roll on its own. Only
engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
To operate the single manual freewheel lever:
1. Push the safety latch in and pull up the manual freewheel lever for freewheel mode (drive disengaged). See
figure 8.
2. Push the manual freewheel lever down for drive mode (drive engaged). See figure 8a.
Figure 8. Freewheel Mode (Drive Disengaged) Figure 8a. Drive Mode (Drive Engaged)
To operate the dual manual freewheel levers:
1. Push the manual freewheel lever on each motor down for freewheel mode (drive disengaged). See figure 9.
2. Pull the manual freewheel lever up on each motor for drive mode (drive engaged). See figure 9a.
Figure 9a. Drive Mode (Drive Engaged)Figure 9. Freewheel Mode (Drive Disengaged)
NOTE: If the lever is difficult to move in either direction, rock your power chair back and forth slightly. The
lever should then move to the desired position.
SAFETY LATCH

Jazzy 1121 17www.pridemobility.com
IV. ASSEMBLY
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require
disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed
to be disassembled and assembled by an end user or by a qualified carer before using the product or making
comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,
resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or
through your authorised Pride Dealer.
SEAT INSTALLATION
ARMREST ADJUSTMENT
CONTROLLER POSITION
SEAT HEIGHT/ANGLE ADJUSTMENT
ANTI-TIP WHEEL ADJUSTMENT
FOOT PLATFORM ADJUSTMENT
Figure 10. Jazzy 1121 Assembly View

Jazzy 112118 www.pridemobility.com
IV. ASSEMBLY
Euro Seat Installation
The Euro Seat is attached to the power base by four seat towers. Each tower is inserted into a receiver on the power
base frame. The seat towers have holes that enable you to adjust the seat height. Ball detent pins are inserted
through the receiver and through the seat towers to secure the seat
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot and you may
lose control of the seat if they do so.
To install the Euro Seat:
1. Lift the seat over the power base.
2. Align each seat tower with the corresponding receiver. See figure 11.
3. Gently allow the seat to slide into each receiver until the seat is at the desired height.
4. Insert the retaining clips into each receiver.
5. Install the armrests (if necessary).
6. Loosen the setscrews on the controller mount.
MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the
outside of the armrest pad. Route the harness under the armrest or toward the inside of the
armrest pad. Use correct tie-down points for the controller harness to prevent the harness from
getting caught in the drive tyres, pinched in the seat frame, or damaged when passing through
doorways.
7. Slide the controller into the armrest.
8. Tighten the setscrews to secure the controller.
9. Use a wire tie to secure the controller harness to the armrest.
10. Plug the controller harness into the connector on the power base.
SEAT TOWER
SEAT
RECEIVER POWER
BASE
RETAINING CLIP
CONTROLLER
MOUNT
Figure 11. Euro Seat Installation/Removal

Jazzy 1121 19www.pridemobility.com
IV. ASSEMBLY
Contour Seat Installation
The Universal Mounting System (UMS) consists of universal parts that may be used on any medium-back or high-
back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions that are
mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to four steel towers.
WARNING!Do not pick up the seat frame by the armrests. They are free to pivot and you may
lose control of the seat if they do so.
To install a contour seat:
1. Set the trapeze bars to the desired height. To change the trapeze bar height, see V. “Comfort Adjustments.”
2. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 12 and 12a.
3. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
4. Flip the seat latch safety down. See figure 12.
WARNING! Make sure the seat latch safety is flipped down before using your power chair.
5. Install the controller into one of the armrests.
6. Plug the controller harness into the power base.
7. Route the harness to ensure that it cannot be pinched in the seat hinge. See firgure 13.
8. Secure the controller harness to the armrest receiver with one or more wire ties.
MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the
outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest
pad. Use correct tie-down points for controller harness to prevent the harness from getting caught
in the drive tires, pinched in the seat frame, or damaged when passing through doorways.
SEAT LATCH SAFETY
FRONT EXTRUSION
FRONT TRAPEZE BAR
REAR TRAPEZE BAR
REAR EXTRUSION
Figure 12. Universal Mounting System
FRICTION LOCK POWER SEAT BASE
SEAT LATCH SAFETY
Figure 12a. Universal Mounting System (Power Seat)

Jazzy 112120 www.pridemobility.com
TO UTILITY TRAY
IV. ASSEMBLY
Transit Securement System (Optional)
If your power chair is equipped with a transit secure-
ment system, it is equipped with manufacturer-
installed front and rear securement brackets. If the
transit securement system is rated for occupied use,
it will also be equipped with positioning belt anchor-
ing brackets. See figure 13a. Refer to the transit
securement package supplement or contact your
authorized Pride Dealer for information on how to
use the transit securement system.
Indicates that tested and
approved power chair, with
similarly labeled tested and
approved seating system,
conforms to ISO 7176-19 for
transport of an occupied power
chair in a motor vehicle.
Indicates power chair
securement points.
Figure 13. Harness Routing
Figure 13a. Transit System Securement Brackets
SECUREMENT BRACKETS