Princess auto PH05-S Parts list manual

TABLE TOP FLAME HEATER
PH05-S/PH05-SS
ASSEMBLY AND OPERATION INSTRUCTIONS
WARNING
Read this instruction before using this
appliance. The appliance must be installed
in accordance with the instructions and
local regulations. The use of this appliance
in enclosed areas can be dangerous and is
PROHIBITED
IF YOU SMELL GAS
•Close the valve of the gas cylinder or
regulator.
•Extinguish all naked flames; do not operate
any electrical appliances.
•Check for leaks as detailed in this instructions.
•If odor persists, contact your dealer or gas
supplier immediately.
•Do the leak test after each changing LPG
cylinder.
•Never check for leaks with a match or open
•Do not store or use gasoline or other
this appliance.
FOR OUTDOOR USE ONLY.
KEEP THE INSTRUCTIONS FOR FUTURE REFERENCE.

CARBON MONOXIDE HAZARD
•This appliance can produce carbon monoxide which
has no odor.
• Using it in an enclosed space can kill you.
•Never use this appliance in a enclosed space such
as a camper, tent, car or home.
•Keep electrical supplycord awayfrom the heated
surfaces.
WARNING:
•Improper installation, adjustment, alteration,
services or maintenance can cause injury, death or
property damage.
•Read the installation, operating and maintenance
instructions thoroughly before installing or servicing
this equipment.
WARNING:
FOR OUTDOOR USE ONLY.
• Cylinders to be used must be constructed
And marked in accordance with US DOT
• Storage indoors is permissible only if the
cylinder is removed.
•The unit should be secured or moved
Indoors if winds exceed 19.5mph.
Note:
Use for 20lb.LPG tank, but it is not supplied.
Use for CSA regulator with 0.6m gas hose.
This regulator is set for an outlet pressure
of 11 inches water column.
TOOLS NEEDED
Philips head screwdriver
Leak detection solution
For questions, replacement
parts, service
PLEASE CONTACT
PRINCESS AUTO LTD.,
1-800-665-8685,
www.princessauto.com
DANGER
- 2 -

PRECAUTIONS
• Installation and services should only be a qualied person.
• Do not use the heater in an explosive atmosphere.
• Before to use, check the hose.
• Disconnect LPG cylinder before moving the heater.
• Do not attempt to alter any parts of the heater.
Example: Using the heater without reector or protection guard.
• The appliance shall not be used in basements or below ground level.
• It must always be placed on a solid and level surface.
• Never replace or substitute the regulator use only that one is suitable both appliance
category and normal pressure of gas.
• Do not clean the heater with cleaners that are combustible or corrosive.
• Do not paint protection guard, control box or reector.
• The LPG gas cylinder valve should be turned off and disconnect the cylinder with the heater
when the heater is not in use.
• Don't not use the heater when it is raining, and do not let any liquid splash to the glass tube
when the heater is working.
• Keep the children away from the heater, always be carefully not to knock down the heater,
which will break the glass tube and might cause injury.
• Do not move the appliance when in operation.
• After a long break of operation, the gas parts in the control box of the heater and the hose
should be inspected for spiders, spider webs or other insects.
Check the heater immediately if any of the following exists:
1. There is smell of gas.
2. The heater is not enough effective.
3. The burner makes popping noise during use (a slight popping noise is normal when the
burner is extinguished after use).
• If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas
supplier immediately.
• The hose with regulator assembly shall be stored on a safety place to avoid it’s accidental
damage.
• Children and adults should be aware of the high surface temperature hazard, and should
keep a safe distance away to avoid clothes burning or igniting.
- 3 -

• Young children should be carefully supervised when they are in the working area of the
heater.
• Clothing or other ammable material should not be hung from the heater, or placed on or
near the heater.
• Do not obstruct the ow of combustion products.
• Keep the ventilation opening of the cylinder enclosure free and clear of debris.
• Do not obstruct the ventilation holes of the cylinder housing.
• Shut off the valve of gas cylinder or the regulator before moving the appliance.
• The tubing or the exible hose must be changed within the prescribed intervals.
• Use only the type of gas and the type of cylinder specied by the manufacturer.
• In case of violent wind particular attention must be taken against tilting of the appliance.
• Storage of the heater indoor is permitted only if the cylinder is disconnected and removed
from the appliance.
• Do not store a spare LP-gas cylinder under or near this heater.
• Never ll the cylinder beyond 80 percent full.
- 4 -

DIAGRAMMATICAL REPRESENTATIONS
OF OUTDOOR AREAS
APPLIANCE STAND AND LOACTION
- The appliance is for outdoor use only. Do not
use it for indoor or in an enclosed area.
- Always maintain proper clearance from
combustible materials, i.e. top 800mm and sides
650mm minimum.
- 5 -

LEAKAGE TEST
Gas connections on the appliance are leak tested at the factory prior to shipment. Possible
mishandling of the appliance during the shipment might contribute to product integrity as a
whole. A complete gas leakage test must be performed again at the installation site. Please
follow the procedure below for leakage test.
- Make a soap solution of one part liquid detergent and one part water. The soap solution can
be applied with spray bottle, brush or rag. Soap bubbles will appear where a leak is present.
- Make sure the control tap is in the “OFF” position (full disk = ●) on the control panel.
- Turn on the gas supply and check for bubbles from the hoses and connections. Presents of
bubble means that a leak path is present.
- If a leak is present, turn OFF the gas supply immediately, tighten any leaking tting carefully,
turn gas again and recheck.
- Never leak test while smoking.
INSTALLATION
Important safety requirements:
THIS APPLIANCE OUTDOOR USE ONLY
1. This appliance shall not be installed or used indoors, in buildings, garages or any other
enclosed area.
2. DO NOT place articles on or against this appliance.
3. DO NOT use or store ammable materials near this appliance.
4. DO NOT operate this appliance unless it is fully assembled with reector and protection
guard in place.
5. Installation and repair should be done by a qualied service person. The appliance must
be inspected before use and at least annually by a qualied service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners
and circulating air passages of the heater and light be kept clean.
6. Please use the pressure regulator and hose assembly supplied with the heater, the
replacement pressure regulator and hose assemblies must be according to ANSI/UL 144.
- 6 -

PARTS LIST-1
Part NO. Part Name QTY Remarks
Bottom Plate
Control Box
Middle Plate
Support
Upper Plate
Plate cover
Glass tube
Damper
Reector
1
1
1
4
1
1
1
1
1
1
2
3
5
6
7
8
9
10
Preassembled in
the Middle plate
Preassembled in
the Middle plate
Preassembled in
upper plate
Picture
- 7 -

PARTS LIST-2
Part NO. Part Name QTY Remarks
Two side bolts
Hook
Mesh Guard
Guard Fastening
Side panel
Front panel
Screw M4
Knob
Nuts
AA battery
3
8
4
4
3
1
66
1
1
1
11
12
13
14
15
16
17
18
19
20
Connect with
damper and
reector
A chain is
preassembled in
this panel
All preassembled
in relative parts
Preassembled in
the front panel
Optional part
Picture
Pieces
- 8 -

HEATER ASSEMBLY
Tools Required:
1 Phillips head screwdriver, 1 adjustable spanner
1. Remove the protective paperboard off the
top of glass tube
Assemble the reflector into the frame parts
using two-side bolts, then use the nuts to
rm the top.
2. Using wing nuts to firm the reflector
completely.
- 9 -
INJECTOR
3. Inner regulator is stored inside. Pl connect
the regulator with 1 pound gas cylinder
tightly.(Cylinder is not provided)
4. Assembling is completed. Start to operate
by reading the following operation manual

OPERATION
Preparation:
You will need to purchase a 1 pound propane cylinder before
you start to use.
Connect the cylinder with the inner regulator
Warning:
Always test the connection place leaks with soapy water.
Any guard or protective device removed for servicing the heater
must be replaced prior to operation.
Warning:
Never use the heater while it is raining, the glass tube would break when it
suddenly met water.
Always turn off the heater while there is a rain.
Never splash any liquid to the glass tube when the heater is working
The glass tube will be extremely hot when it is working, never try to touch it and
Keep the children away from the heater.
Always ensure the heater stands rmly, the glass tube may break if the heater was
fell down onto ground.
Never use the heater if the glass tube has any crack
●
●
●
●
●
●
LIGHTING INSTRUCTIONS
Check and ensure that an AA battery is inside the ignition
chamber and has power. Ensure
The anode (+) faces outside.
Ensure that the control knob is OFF. Slowly open the
gas cylinder valve.
Press and turn the control knob to LIGHT position,
push the igniter to generate spark while keeping control
knob in pressed position
Check for pilot ame through glass tube. If pilot does
not light, turn control knob to ‘OFF’ position wait two
minutes minimum and try again from the start. Some
attempts may be necessary.
If the pilot alight, keep control knob pressed for 15
seconds then turn the control knob to ‘LOW’.
For maximum heat turn control knob to ‘HIGH’.
To turn heater off, turn control knob to ‘OFF’.
Close the vlave of the gas cylinder or the regulator after
use.
1.
2.
3.
4.
5.
6.
7.
OFF
LIGHT
LOW
HIGH
OFF
LO
HI
WARNING
FOR YOUR SAFETY:
● DO NOT touch or move heater for at
Least 45 minutes after use.
● Allow all burner elements to cool
before touching.
NOTE
● In a salt-air environment (such as near an
Ocean) corrosion occurs more quickly than
normal.
● Frequently check for corroded areas and
Repair them promptly.
● Wait until heater is cool before covering.
- 10 -

CLEANING AND MAINTENANCE:
Storage between usage:
During periods of extended inactivity or when transporting:
CLEANING/MAINTENANCE/STORAGE
●
●
●
●
●
●
●
●
●
●
●
●
●
●
- 11 -
To enjoy outstanding performance of your heater for years make sure to perform the
following maintenance activities on a regular basis:
Keep exterior surfaces clean.
-Use warm soapy water for cleaning. Never use flammable, corrosive or abrasive
cleaners.
-While washing your unit, be sure to keep the area around the burner and pilot assembly
dry at all time. If the gas control is exposed to water in any way, do NOT try to use it. It
must be replaced.
After a long break from operation, the unit should be inspected for spiders, spider webs
or other insects.
Air ow must be unobstructed. Keep controls. Burner and circulating air passageways
clean.
Signs of possible blockage include:
-Gas odor with extreme yellow tipping of ame.
-Heater does NOT reach the desired temperature.
-Heater glow is excessively uneven.
-Heater makes popping noises.
Spider and insects can nest in burner or orices.
This dangerous condition can damage heater and render it unsafe for use. Clean burner
holes by using a heavy-duty pipe cleaner.
Compressed air may help clear away smaller particles.
Carbon deposits may create a re hazard. Clean reector and glass tube inside abo with
soapy water if any carbon deposits develop. Always be careful when cleaning the glass
tube.
Turn the control knob to “OFF” position.
Take cylinder out of product.
Store heater upright in an area sheltered away from weather conditions (such as rain,
sleet, hail, snow).
if desired, cover heater to protect exterior surfaces and to help prevent dust and debris
collecting in air passages.
Turn the control knob to “OFF” position.
Disconnect LP Cylinder and move to a secure, well-ventilated location outdoors.
DO NOT store in a location that will exceed 50 degrees C.
Store heater upright in an area sheltered away from weather conditions (such as rain,
sleet, hail, snow).
If desired, cover heater to protect exterior surfaces and to help prevent dust and debris
collecting in air passages.

Troubleshooting
PROBLEM PROBABLE CAUSE SOLUTION
Gas valve may be OFF
Fuel Tank empty
Air in supply system
Loose connection
Debris around pilot
Loose connection
Thermocouple bad
Gas leak in line
Lack of fuel pressure
Pressure is low
Control Valve not ON
Thermocouple bad
Pilot light assembly bent Or
not in correct location .
Turn the gas valve ON
Purge air from lines
Clean dirty area
Tighten connection .
Replace Thermocouple
Check connections
Fuel tank is near empty
Fuel tank is near empty
Remove, clean and replace
Turn valve to ON .
Replace Thermocouple
Pilot will not light
Pilot will not stay on
Burner will not light
•For questions, replacement parts, service,
PLEASE CONTACT PRINCESS AUTO LTD.,
1-800-665-8685,
www.princessauto.com
- 12 -