Priorit PRIODOOR ETX-RDA User instructions

Assembly and
Operating Manual
PRIODOOR ETX-RDA
Outflow Closure for
Smoke Protection Pressure Systems
Opening Sh ft Side
Status: 10/2019
EP.A.10154-3

2
Dear customer,
You've dec ded n favour of a h gh-qual ty PRIORIT product.
Thank you very much.
Please carefully comply w th the operat ng manual below so we can guarantee that your whole system
funct ons perfectly.
We can't undertake any warranty w thout compl ance.
We expressly reserve the r ght—even w thout separate not ce—to make techn cal changes serv ng to
mprove our products or occas oned by legal changes.
Th s operat on/assembly manual may not be repr nted or reproduced—even n part—w thout the wr tten
consent of PRIORIT AG.
PRIORIT AG, 63457 Hanau
Phone: [phone], Fax: [phone],
Ema l : nfo@pr or t.de , www.pr or t.de

3
Table of contents
Important notes ........................................................................................................................................... 4
General safety-related notes ...................................................................................................................... 5
Intended use ............................................................................................................................................... 5
Funct onal test ng, safety-related rev ew .................................................................................................... 5
Care and ma ntenance ............................................................................................................................... 5
Warranty, declarat on of transfer ................................................................................................................ 6
Property r ghts ............................................................................................................................................ 6
Assembly frame erect on ............................................................................................................................ 7
Assembly frame nstallat on ........................................................................................................................ 7
Door element assembly .............................................................................................................................. 9
Installat on deta l ETX-RDA n sol d wall .................................................................................................. 10
Installat on deta l ETX-RDA n PRIOWALL .............................................................................................. 10
Door element emergency open ng ........................................................................................................... 11
Techn cal nformat on concern ng the cha n motor ................................................................................... 12
Cha n motor techn cal data ....................................................................................................................... 15
Recommended nspect ons ...................................................................................................................... 18

4
Important notes
Sett ng up and assembl ng the product plumb and hor zontal s
mperat ve!
Do not set nd v dual parts down on the corners, and lay out the storage
area n advance w th soft mater al such as a pack ng blanket.
Only qual f ed personnel may nstall th s!

5
General safety-related notes
• The operat ng/assembly must be constantly stored where the product s be ng used.
• Legally prescr bed safety not ces are to be attached to places v s ble to the users.
• All safety and hazard not ces as well as the name plate must be kept n leg ble cond t on.
• Use the product only when t's n proper cond t on.
• Observe the techn cal data n our catalogue or data sheet for each product.
• Improper nstallat on can mpa r the protect on funct on.
• Observe all of the not ces n th s operat on and ma ntenance manual.
• The lock ng systems may not be mod f ed or exchanged.
• Only qual f ed personnel may conduct nstallat on!
Intended use
• The products descr bed n th s operat on/assembly manual are bu lt accord ng to the latest
technology and recogn zed safety-related rules.
• They may only
- be used as ntended ndoors and
- n safety-related flawless cond t on.
• Any other use s cons dered mproper.
PRIORIT assumes no l ab l ty for damage or consequent al damage ar s ng therefrom.
Funct onal test ng, safety-related rev ew
Care and ma ntenance
• Test cha n-dr ve sem -annually for funct on.
• V sual nspect on of the door leaf and case for mechan cal damage; replace damaged parts f
necessary.
• V sual nspect on for corros on damage; replace affected components f necessary.
• V sual nspect on of the door leaf, case, and f tt ngs for contam nat on; clean f necessary.
• V sual nspect on of the smoke- and f re-protect on seals for damage and completeness; replace
seals f necessary.
• M ld, popular household cleaner can be used for external clean ng of the nspect on closures
(only w th plast c-coated doors).
• The product s to be protected from water, penetrat ng mo sture, or water spray.
• If safety-relevant damage s dent f ed, t must be repa red w th or g nal parts before further use.
• Conduct of a complete cycle test sem -annually.

6
Warranty, declarat on of transfer
The assembly nstruct ons must be str ctly adhered to n order to guarantee our products' opt mal
funct on ng.
The warranty from PRIORIT extends to the del vered products.
Changes or mod f cat ons to the des gn may be conducted only after consultat on w th PRIORIT;
otherw se the cert f cat on/warranty w ll be nval dated.
The nstaller assumes the warranty for assembly serv ces.
Warranty and l ab l ty cla ms for personal njury and property damage are excluded f they can be traced
back to one or more of the follow ng causes:
• The product s not be ng used as ntended.
• There s mproper assembly, start-up, operat on, or ma ntenance.
• Instruct ons concern ng transport, storage, operat on, and assembly have not been observed.
• Unauthor zed construct onal changes have been made to the product.
• Improper repa rs have been made.
• Emergenc es caused by th rd part es' external act ons, and force majeure have occurred.
Property r ghts
Ut l ty models have been f led w th the German Patent Off ce n order to safeguard nnovat on and
des gn.

7
Assembly frame erect on
• Screw together the assembly frame's
upr ght and d agonal frame parts w th 4.5
mm x 80 mm countersunk screws.
Assembly frame nstallat on
• Attent on shaft tasks: Protect yourself and
your tools against falling!
• Place the assembled frame nto the wall
open ng.
• Al gn t plumb and hor zontal.
• Arrange enc rcl ng open gap evenly.
• Lay non-flammable stab l zer mater al (not
ncluded n the del very) under the screw
po nts.
• Allow the stab l zer mater al below to
protrude transversally; t later serves as a
support surface for the door element.
• Underlay vert cal case.
• Secure aga nst fall ng out!

8
Stab l zer mater al
• F x n sol d wall w th 8 x 120 dowels.
• Underlay screw po nts.
• Underlay vert cal case.
• F ll empty space between assembly frame and
wall open ng w th plaster.
• The cases and door element should
always be nstalled plumb and horizontal.
• It s mperat ve to use a cross laser!

9
Door element assembly
• Rotate the door element nto nstallat on
pos t on and set n front of the wall
open ng.
• Gu de the connect on cable hang ng on the
lock s de toward the front and allow to
hang.
• L ft the door element nto the wall open ng
and set t up on the protrud ng stab l zer
mater al beneath.
• Al gn the door element flush w th the
assembly frame and secure aga nst t pp ng
or fall ng out.
• Screw the door frame's cases w th the
assembly frame us ng the 4.5 mm x 80
mm countersunk screws.
• The door leaf can be opened after
screw ng the case w th the assembly
frame.
• A 24 V power supply or a test dev ce s
needed for th s. Cable wh te 24 V; cable
brown −24 V
• After complet ng funct onal nspect on, lay
the connect on cable between the
assembly frame and the wall n the shaft
(see deta l below).
• Grout wall-closure jo nts w th mortar or
plaster depend ng on the type of wall.
• Make holes between the assembly frame
and the wall at the he ght of the place
where the connect on cable protrudes.
• Take care not to damage the connect on
cable wh le dr ll ng.
• Thread the connect on cable through the
hole and nto the shaft.
Connect on cable
Countersunk screw
4.5 x 80

10
Countersunk screw
Installat on deta l ETX-RDA n sol d wall
Assembly frame Dowel
Door element—p ctured case
Installat on deta l ETX-RDA n PRIOWALL
Countersunk screws
5 - 20

11
M5x45 countersunk
screws
Door element emergency open ng
• Unscrew the two screws secur ng the
bracket holder that holds the cha n
motor.
• Important! Do not use a screwdriver
but a hand screwdriver.
• Move the door manually toward the
shaft.
• Repa r, ma nta n, or replace the cha n
motor f requ red.
• Extend the cha n motor and br ng the
bracket holder together w th the door
leaf nto screw- n pos t on.
• Screw the bracket holder to the case
aga n and do a funct on check.

12
Techn cal nformat on concern ng the cha n motor

13

14

15

16
Cha n motor techn cal data

17

18
Recommended nspect ons
Reference smoke damper
Inspect on date
Check ng the actuator w r ng for damage
Check ng the l m t sw tch w r ng for damage
Check ng outflow closure's cleanl ness and
clean ng f necessary
Check ng the cond t on of the leaves and seals;
repa r f necessary then generat on of the
correspond ng report
Conf rmat on that the smoke damper opens
(w th n 60 s) and closes (w th n 60 s) us ng the
control system. Observat on of the outflow
closure; repa r then generat on of the
correspond ng report f necessary
Conf rmat on of the l m t sw tch's OPEN and
CLOSED pos t ons; repa r f necessary then
generat on of the correspond ng report
Conf rmat on that the smoke damper fulf ls ts
funct on as part of the smoke extract on system
Conf rmat on that the smoke damper has been
left n ts ready pos t on
Note: A smoke damper s generally part of a smoke extract on system.
Consequently, an nspect on of the ent re system should be completed as governed by the operat on
and ma ntenance requ rements.