Pro-Cut PFM 9.1 DRO User manual

TECHNICAL MANUAL

PG / Ø2 800.543.6618

WWW.PROCUTUSA.COM PG / Ø3
TECHNICAL MANUAL
P ·800.543.6618
F ·603.298.8404
[email protected]
www.procutusa.com

PG / ØØ4 800.543.6618
PFM 9.1 DRO Notes
· The 9.1 comes standard with a 3 legged trolley (50-380)
· Refer to page #78 in the 9.2 technical manual
· The 9.1 comes with a 50-238 Cutting Head
· The 9.1 is not compatible with the G2X (50-1200) cutting head
· The 9.1 is not compatible with the GYR system

WWW.PROCUTUSA.COM PG / ØØ5
Positioning The Cutting Head
Notice that there are several mounting holes in the slide plate that can be used to lock the cutting head. The
cutting head assembly can be secured into any one of the holes. It is a good idea to clean out these holes as
well as the dovetail and plate surfaces when you change cutting head position, as they can easily fill up with
metal chips. Use the T-handle 6mm allen wrench to remove the securing screw and center the head so the
cutting arms will straddle the rotor.
USING THE 50-238 CUTTING HEAD
It is critical that you pull the tool holder plate
back into the dovetail so that it is square as you
tighten the securing screw.You can use one hand
to push the cutting head firmly back into the
dovetail as you tighten the set screw with your
other hand. If the tool holder is not squarely and
firmly pressed into the dovetail, a poor surface
finish will result.

PG / ØØ6 800.543.6618
Next you will set the shut-off cam. Crank the feed knob until the tips clear the outside edge of the rotor.
Loosen the cam screw and slide the cam back until it contacts the automatic shut-off switch plunger.
Tighten the cam screw. The cam will press the shut-off switch when the tips clear the rotor. This allows
for unattended operation.
SET SHUT-OFF CAM
The Pro-Cut will mount right-side up on one side and upside down on the other. Always start right-side
up; this way, when you proceed to the other side of the vehicle, the offset of the cutting head will already
be set, with the cutting head firmly in the dovetail. Never attempt to move the cutting head laterally
with the lathe upside down.
NOTE

YES
37-077
NO
Assembly:
11
1516
13
14
4
6
7
8
5
10
12
9
2
13
3
1
9/4/2012
17
ITEM
NO. PART NUMBERQTY.
1 50-292 1
2 50-373 1
3 50-374 1
4 50-253 1
5 50-254 1
6 50-098 2
7 50-252 1
8 50-251 1
9 50-053 1
10 37-077 4
11 37-184 1
12 36-002 2
13 37-003 3
14 37-082 2
15 50-365 1
16 50-364 1
17 36-010 2
WWW.PROCUTUSA.COM PG / ØØ7
9.1 DRO PARTS DIAGRAM 50-238 CUTTING HEAD ASSEMBLY

Global inquiries please see:
www.procutusa.com
© PRO-CUT INTERNATIONAL, LLC
Pro-Cut International, LLC
10 Technology Drive #4
West Lebanon, NH 03784
P. 800.543.6618 / 603.298.5200
F. 603.298.8404
E. [email protected]
50-736
PRINTED WITH PRIDE IN THE U.S.A.