Pro-face PS-3710A Series User manual

+DUGZDUH0DQXDO
36$36$6HULHV
Industrial automation
Elincom Group
EuropeanUnion:www.elinco.eu
Russia: www.elinc.ru

1
Preface
Thank you for purchasing Pro-face’s PS-3710A/PS-3711A Series (Hereafter referred to as the “PS-A unit”).
Before operating your PS-A unit, be sure to read this manual to familiarize yourself with the PS-A unit’s operation
procedures and features.
©2007 Copyright Digital Electronics Corporation. All rights reserved.
Product names used in this manual are the trademarks / registered trademarks of their respective owners.
NOTICE
1. Copying this manual’s contents, either in whole or in part, is prohibited without the express permission of Digital
Electronics Corporation, Japan.
2. The information contained in this manual is subject to change without notice.
3. If you should you find any errors or omissions in this document, please contact Digital Electronics Corporation to
report your findings.
4. Regardless of Clause 3 above, Digital Electronics Corporation shall not be held responsible for any damages,
losses or third-party damages resulting from the use of this product.

2
Essential Safety Precautions
All safety-related procedures stated in this document must be followed to operate the PS-A correctly and safely. Be sure to
read this and any related documents thoroughly to understand the correct operation and functions of the PS-A unit.
Safety Icons
Throughout this manual, these icons provide essential safety information for PS-A operation procedures requiring special
attention. These icons indicate the following levels of danger:
System Design
Indicates situations where severe bodily injury, death or major equipment damage
can occur.
Indicates situations where slight bodily injury or minor equipment damage can
occur.
Indicates actions or procedures that should NOT be performed.
Indicates actions or procedures that MUST be performed to ensure correct unit
operation.
Do not create PS-A touch panel switches that could possibly endanger the safety of personnel or
equipment.
A malfunction of the PS-A unit, its I/O unit(s), cable(s), or other related equipment can cause unexpected
output signals, leading to a serious accident. Be sure to design all important machine operation switches
so they are operated via a separate control system, and not via the PS-A.
Do not create PS-A touch panel switches to control machine safety operations, such as an emergency
stop switch. Install these switches as separate hardware switches, otherwise severe bodily injury or
equipment damage can occur.
Be sure to design your system so that a communication fault between the PS-A and its host controller will
not cause equipment to malfunction. This is to prevent any possibility of bodily injury or equipment
damage.
Do not use the PS-A as a warning device for critical alarms that can cause serious operator injury,
machine damage or can halt system operation. Critical alarm indicators and their control/activator units
must be designed using stand-alone hardware and/or mechanical interlocks.

3
Handling
Wiring
Maintenance
Do not use the PS-A with aircraft control devices, aerospace equipment, central trunk data transmission
(communication) devices, nuclear power control devices, or medical life support equipment, due to these
devices’ inherent requirements of extremely high levels of safety and reliability.
When using the PS-A with transportation vehicles (trains, cars, and ships), disaster and crime prevention
devices, various types of safety equipment, and medical devices that are not life-support related, use
redundant and/or failsafe system designs to ensure proper reliability and safety.
After the PS-A unit’s backlight burns out the touch panel is still active, unlike the PS-A unit’s “Standby
Mode”. If the operator fails to notice that the backlight is burned out and touches the panel, a potentially
dangerous machine operation error can occur. Therefore, do not create PS-A unit touch panel switches
that may cause injury and/or equipment damage. If your PS-A unit’s backlight suddenly turns OFF, use the
following steps to determine if the backlight is actually burned out.
1) If the PS-A unit’s “Backlight Control” is not set and the screen has gone blank, your backlight is burned
out.
2) If the PS-A unit’s “Backlight Control” is set to Standby Mode and the screen has gone blank, and
touching the screen or performing another input operation does not cause the display to reappear,
your backlight is burned out.
Do not disassemble or modify the PS-A unit. Doing so may cause a fire or an electric shock.
Do not operate the PS-A in an environment where flammable gases are present, since it may cause an
explosion.
To prevent electrical shock or equipment damage, unplug the PS-A unit’s power cord from the power
supply prior to installing or wiring the PS-A.
Do not use the voltage not specified in the manual. Doing so may cause a fire or an electric shock.
Do not connect or disconnect Host and PS-A unit communication cables while the PS-A is turned ON.
The PS-A uses a lithium battery for backing up its internal clock data and the battery may explode if it is
replaced incorrectly. When replacement is required, use a Pro-face-designated replacement product.
SEE “4.6 Replacing the Internal Battery” (page 4-13)

4
Installation
Wiring
Maintenance
Unit Disposal
General Safety Precautions
Be sure all cable connectors are securely attached to the PS-A unit. A loose connection may cause
incorrect input or output signals.
Be sure to ground the PS-A unit’s FG wire separately from other equipment FG lines. Also, be sure to use
a grounding resistance of 100Ωor less and a 2mm2or thicker wire, or your country’s applicable standard.
Otherwise, electric shock or malfunctions may result.
Be sure to use only the designated torque to tighten the PS-A unit’s terminal block screws. If these screws
are not tightened firmly, it may cause a short-circuit, fire or incorrect unit operation.
Be sure that metal particles and wiring debris do not fall inside the PS-A unit. They can cause a fire,
malfunction or incorrect unit operation.
Do not reset or turn the PS-A OFF, or insert or remove the CF Card while the PS-A unit’s CF Card or hard
disk is being accessed. Otherwise, CF Card and the hard disk internal data may be damaged or lost.
When the product is disposed of, it should be done so according to your country’s regulations for similar
types of industrial waste.
Do not press on the PS-A unit’s display with excessive force or with a hard object, since it can damage the
display. Also, do not press on the touch panel with a pointed object, such as the tip of a mechanical pencil
or a screwdriver, since doing so can damage the touch panel.
Do not install the PS-A where the ambient temperature exceeds the specified range. Doing so may cause
a unit malfunction.
To prevent abnormally high temperatures from occurring inside the PS-A, do not restrict or block the PS-A
unit’s rear-face ventilation slots.
Do not operate the PS-A in areas where large, sudden temperature changes can occur. These changes
can cause condensation to form inside the PS-A, possibly causing it to malfunction.
Do not allow water, liquids or metal fragments to enter inside the PS-A unit’s case, since they can cause
either a malfunction or an electric shock. The allowable pollution degree is 2.

5
LCD Panel Usage Precautions
• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin,
immediately rinse the area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse
your eyes with running water for at least 15 minutes and consult a doctor.
• The PS-A unit’s LCD screen may flicker or show unevenness in the brightness of certain images or at some contrast
settings. This is an LCD characteristics and not a product defect.
• Some LCD screens may have differences in brightness and tone. Please be aware of this difference when using
multiple units side by side.
• Depending on the ambient temperature, LCD screens may sometimes look whitish (at high temperatures) or blackish
(at low temperatures). This is an LCD characteristic and not a product defect.
• Some of PS-A unit's LCD screens may contain black and white colored pixels. This is an LCD characteristic and not a
product defect.
• Extended shadows, or "Crosstalk" may appear on the LCD screen. This is an LCD characteristic and not a product
defect.
• The color displayed on the PS-A unit’s LCD screen may appear different when seen from outside the specified viewing
angle. This is an LCD characteristic and not a product defect.
Do not operate or store the PS-A in locations where it can be exposed to direct sunlight, high
temperatures, excessive dust, moisture or vibration.
Do not operate or store the PS-A where chemicals evaporate, or where chemicals are present in the air.
Corrosive chemicals: Acids, alkalines, liquids containing salt
Flammable chemicals: Organic Solvents
Do not use paint thinner or organic solvents to remove dirt or oil from the PS-A unit’s surface. Instead, use
a soft cloth moistened with a diluted neutral detergent.
Do not use or store the PS-A in areas with direct sunlight, since the sun’s ultraviolet rays may cause the
LCD’s quality to deteriorate.
Do not store the PS-A in an area where the temperature is lower than that recommended in the PS-A
unit’s specifications. Doing so may cause the LCD display’s liquid to congeal, which can damage the LCD.
Also, if the storage area’s temperature becomes higher than the specified level, the LCD’s liquid may
become isotropic, causing irreversible damage to the LCD. Therefore, only store the PS-A in areas where
temperatures are within the PS-A unit’s specifications.
After turning OFF the PS-A unit, be sure to wait at least 5 seconds before turning it ON again. The PS-A
unit may not operate correctly if it is restarted too quickly.
Due to the possibility of unexpected accidents, be sure to back up the PS-A unit's data regularly.

6
• When the same image is displayed on the PS-A unit’s screen for a long period, an afterimage may appear when the
image is changed. If this happens, turn off the PS-A, wait 10 seconds and then restart the unit. This is an LCD
characteristic and not a product defect.
• To prevent an afterimage:
* Set the PS-A unit’s display OFF feature when you plan to display the same screen image for a long period of time.
* Change the screen image periodically and try to not display the same image for a long period of time.
Information Symbols
This manual uses the following icons:
About the Manuals
For the detailed information on PS-A series, refer to the following manuals.
• PS-3710A/PS-3711A Series Hardware Manual
• PS-3710A/PS-3711A Series Reference Manual
• PS-3710A/PS-3711A Series API Reference Manual
• Installation Guides for various optional items
The manuals can be downloaded from Pro-face Home Page, “Otasuke Pro!”.
“Otasuke Pro!” URL
http://www.pro-face.com/otasuke/
Indicates a warning or a product limitation. Be sure to follow the instructions given with
this icon to ensure the safe operation of the PS-A.
* Indicates useful or important supplemental information.
Contains additional or useful information.
Indicates pages containing related information.
• PS-3710A/PS-3711A specifications may change when optional items are used.
Check the optional item installation guides’ specifications for variances, if any.
SEE

7
PS-3710A/PS-3711A Series Model Names
The term “PS-3710A/PS-3711A” Series refers to the following numbers:
Series Models Type
PS-3710A Series
PS3710A-T41 PS-3710A Series AC Power Supply Type
PS3710A-T42
PS3710A-T41-24V PS-3710A Series DC Power Supply Type
PS3710A-T42-24V
PS-3711A Series
PS3711A-T41 PS-3711A Series AC Power Supply Type
PS3711A-T42
PS3711A-T41-24V PS-3711A Series DC Power Supply Type
PS3711A-T42-24V

8
Package Contents
The following items are included in the PS-A unit’s package. Before using the PS-A, please check that all items listed
here are present.
This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or
missing, please contact your local PS-A distributor immediately.
PS-A Unit: 1 • Installation Guides
(Set of Japanese/Set
of English)
• Warning/Caution
Information (1)
Installation Gasket: 1
(Attached to the PS-A
unit)
Installation Fasteners: 4
per set x2
USB Cable Clamp: (2 ports) 2
Power Connector: 1
Power Switch cover (1 set) (cover:1, secrew:1)
(AC Power Supply type Only)
• Be careful when installing the PS-A not to damage the built-in HDD.
(for AC Power Supply type)
(5.08mm [0.2in.] pitch)
AC Power Supply type
(only for PS-3711A Series
DC Power Supply type)
(only for PS-3710A Series
DC Power Supply type)
(7.62mm [0.3in.] pitch)
DC Power Supply type
PS-3710A Series PS-3711A Series

9
UL/c-UL/CSA Approval
• UL listed products
• c-UL listed products
• CSA listed products
• Product List
UL/c-UL File No.: E220851, E210412
CSA File No.219866
Industrial Control Equipment refer to UL508 see [a] in the
“Product List“
Suitable for use in Class I, Division 2,
Groups A, B, C, and D Hazardous (clas-
sified) locations, or Non-Hazardous
Locations.
refer to
ANSI/ISA 12.12.01 see [b] in the “Product List“
Process Control Equipment refer to CSA-C22.2
No.142 see [c] in the “Product List“
Suitable for use in Class I, Division 2,
Groups A, B, C, and D Hazardous (clas-
sified) locations, or Non-Hazardous
Locations.
refer to
CSA-C22.2 No. 213 see [d] in the “Product List“
Process Control Equipment refer to CSA-C22.2
No.142 see [e] in the “Product List“
Product Model No. Registration Model No. UL c-UL CSA
[a] [b] [c] [d] [e]
PS3710A-T41 3580301-01 --
PS3710A-T41-24V 3580301-12 --
PS3711A-T41 3580301-03 --
PS3711A-T41-24V 3580301-11 --
PS3710A-T42 3580301-01  -
PS3710A-T42-24V 3580301-12  -
PS3711A-T42 3580301-03  -
PS3711A-T42-24V 3580301-11  -

10
<Cautions>
Be aware of the following items when building the PS-A into an end-use product:
• The PS-A unit’s rear face is not approved as an enclosure. When building the PS-A unit into an end-use product, be
sure to use an enclosure that satisfies standards as the end-use product’s overall enclosure.
• The PS-A unit must be used indoors only.
• Install and operate the PS-A with its front panel facing outwards.
• If the PS-A is mounted so as to cool itself naturally, be sure to install it in a vertical panel. Also, it’s recommended that
the PS-A should be mounted at least 50mm [1.97in.] away from any other adjacent structures or machine parts. The
temperature must be checked on the final product in which the PS-A is installed.
• For use on a flat surface of a Type 4X (Indoor Use Only) and/or Type 12 Enclosure.
• Type 4X (Indoor Use Only) and/or 12 Enclosure, when the hatch for Front USB Port is secured by screw.
Type 1 Enclosure, when the hatch for Front USB Port is open.
<Compliance and Handling Cautions in Hazardous Locations>
• Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous Locations only.
• WARNING: Explosion hazard - substitution of components may impair suitability for Class I, Division 2.
• WARNING: Explosion hazard - do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
• WARNING: Explosion hazard - When using the PS-A with the AC type power supply, be sure to attach the Power
Switch Cover.
SEE “3.2.3 Attaching the Power Switch cover” (page 3-9)

11
<Control Drawing of USB I/F on PS-A's Front Module>
The information below concerns the use of the USB I/F located on the PS-A unit's front modules used in Class I, Division
2 Groups A, B, C, and D hazardous locations (from Doc No. 35016429).
Notes:
1. Nonincendive Circuit Parameters:
Front USB Port:
Voc = 5.0 V
Isc = 1.25 A
Ca = 10 µF
La = 16 µH
2. Selected Associated Nonincendive Field Wiring Apparatus shall satisfy the following:
3. If the electrical parameters of the cable are unknown, the following values may be used:
Capacitance = 60 pF/ft
Inductive = 0.20 µH/ft
4. Nonincendive Field Wiring must be installed in accordance with article 501.10(B) of the National Electrical Code
ANSI/NFPA 70.
5. Nonincendive Field Wiring Apparatus shall not contain or be connected to another source of power.
Nonincendive Field
Wiring Apparatus -Front module of PS-A unit
Voc ≤Vmax
Isc ≤lmax
Ca ≥Ci + C cable
La ≥Li + L cable
PS-A’s Front module
USB Pin Description
1. Vcc
2. D-
3. D+
4. GND
(See Note 1 for details)
Shield GND
Nonincendive Field
Wiring Apparatus
1 2 3 4
AssociatedNonincendiveFieldWiring
Apparatus

12
CE Marking
PS3710A-T41/PS3710A-T42/PS3711A-T41/PS3711A-T42 units are CE marked products that conform to EMC
directives and Low Voltage Directives EN55011 Class A, EN61000-6-2, and EN60950-1.
PS3710A-T41-24V/PS3710A-T42-24V/PS3711A-T41-24V/PS3711A-T42-24V units are CE marked products that
conform to EMC directives EN55011 Class A and EN61000-6-2.
FCC Statement
The following units conform to the FCC Rules.
United States FCC Part 15, Subpart B, Class A EMI Compliance Statement:
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his or her own expense.
About Revision
The nameplate on the PS-A has the revision number of the PS-A. In the example below, the asterisk, which is placed at
the “A” position, shows that the revision number is “A”.
Product Model No.
PS3710A-T42
PS3710A-T42-24V
PS3711A-T42
PS3711A-T42-24V
When PS-A is Rev. A

13
Contents
Preface...................................................................................................................... 1
Essential Safety Precautions..................................................................................... 2
Information Symbols.................................................................................................. 6
About the Manuals .................................................................................................... 6
PS-3710A/PS-3711A Series Model Names .............................................................. 7
Package Contents..................................................................................................... 8
UL/c-UL/CSA Approval.............................................................................................. 9
CE Marking.............................................................................................................. 12
FCC Statement........................................................................................................ 12
About Revision........................................................................................................ 12
Contents.................................................................................................................. 13
Chapter 1 Overview
1.1 System Design................................................................................................1-2
1.1.1 PS-3710A Series ..................................................................................................1-2
1.1.2 PS-3711A Series...................................................................................................1-3
1.2 Accessories ....................................................................................................1-4
1.2.1 Option Items .........................................................................................................1-4
1.2.2 Maintenance Items ...............................................................................................1-5
1.3 Part Names and Functions.............................................................................1-6
1.3.1 PS-3710A Series ..................................................................................................1-6
1.3.2 PS-3711A Series...................................................................................................1-9
1.4 Prior to Operating the PS-A Unit...................................................................1-12
1.4.1 Power Supply......................................................................................................1-12
Chapter 2 Specifications
2.1 PS-3710A Series ............................................................................................2-2
2.1.1 General Specifications..........................................................................................2-2
2.1.2 Performance Specifications ..................................................................................2-6
2.1.3 Interface Specifications.........................................................................................2-8
2.1.4 Dimensions.........................................................................................................2-18
2.2 PS-3711A Series...........................................................................................2-21
2.2.1 General Specifications........................................................................................2-21
2.2.2 Performance Specifications ................................................................................2-25
2.2.3 Interface Specifications.......................................................................................2-27
2.2.4 Dimensions.........................................................................................................2-37

14
Chapter 3 Installation and Wiring
3.1 Installation • Uninstallation..............................................................................3-2
3.1.1 Installation.............................................................................................................3-2
3.2 Peripheral Devices Installation .......................................................................3-6
3.2.1 Removal/Attachment the Rear Cover...................................................................3-6
3.2.2 PS-A Internal View................................................................................................3-8
3.2.3 Attaching the Power Switch cover ........................................................................3-9
3.2.4 Main Memory Installation......................................................................................3-9
3.2.5 Expansion Board (PCI) Installation.......................................................................3-9
3.2.6 PCMCIA Unit Installation ....................................................................................3-12
3.2.7 HDD/SSD Unit Installation..................................................................................3-14
3.2.8 CF Card Insertion/Removal ................................................................................3-16
3.2.9 USB Cable Clamp Attachment/Removal ............................................................3-19
3.2.10 Attach the PS-A unit to an Arm.........................................................................3-21
3.3 Wiring Precautions........................................................................................ 3-22
3.3.1 Connecting the Power Cord................................................................................3-22
3.3.2 Connecting the Power Supply.............................................................................3-28
3.3.3 Grounding...........................................................................................................3-29
3.3.4 I/O Signal Line Placement ..................................................................................3-29
Chapter 4 Maintenance
4.1 Cleaning the Display....................................................................................... 4-2
4.2 Cleaning the Fan Filter ................................................................................... 4-2
4.3 Periodic Check Points.....................................................................................4-3
4.4 Replacing the Installation Gasket................................................................... 4-4
4.5 Replacing the Backlight.................................................................................. 4-6
4.5.1 PS-3710A Series ..................................................................................................4-7
4.5.2 PS-3711A Series.................................................................................................4-10
4.6 Replacing the Internal Battery ...................................................................... 4-13

1-1
1Overview
1. System Design
2. Accessories
3. Part Names and Functions
4. Prior to Operating the PS-A Unit
This chapter describes peripheral devices that can be connected to PS-A Series units along with the name and
functions of each part.

PS-3710A/PS-3711A Series Hardware Manual
1-2
1.1 System Design
1.1.1 PS-3710A Series
The following diagram illustrates the standard range of items that can be connected to PS-3710A Series units.
PS-3710A Series
Inside of PS-A unit
Front of PS-A unit
Side of PS-A unit
Bottom of PS-A unit
PCMCIA I/F
(2 ports)
DVD-ROM Drive
FD Drive
Expansion unit I/F
Line Input I/F
USB I/F
(4 ports)
USB I/F
CF Card I/F
(TYPE II, 1 port)
Mic Input I/F
Speaker Out I/F
Hub
Speaker
Mic
CF
Central Network Line
*1*2
*1*2
*3
Main Memory Module
CF Cards
*2
*2 *2
CF
CF Cards
Main Memory I/F
Peripherals
(commercial type)
Peripherals
(commercial type)
Peripherals
(commercial type)
USB 2.0 Compatible
Peripherals(commercial type)
PCI Board
(commercial type)
(commercial type)
(commercial type)
(commercial type)
CF Card Adaptor
PCMCIA Card
Pin-jack Cable
(commercial type)
RS-232C Cable
COM3
COM1/COM2/COM3/COM4
*4
*1 Built-in accessory only
*2 Digital Electronics Corporation's optional devices and commercial products.
*3 When setting RS-232C mode for COM3.
*4 When setting RS-422 or RS-485 mode for COM3.
Please refer to 1.2 Accessories.
Ethernet I/F
(2 ports)
LAN1:10BASE-T/100BASE-TX Cable (commercial type)
LAN2:10BASE-T/100BASE-TX/1000BASE-T Cable (commercial type)
RAS I/F
RAS Cable
(Produces by users)
(1 port)
USB 2.0 Compatible
Peripherals(commercial type)
PS/2 Keyboard
RS-422 Cable
RS-485 Cable
PS/2 Keyboard I/F
IDE I/F

Chapter 1 Overview
1-3
1.1.2 PS-3711A Series
The following diagram illustrates the standard range of items that can be connected to PS-3711A Series units.
PS-3711A Series
Inside of PS-A unit
Bottom of PS-A unit
Side of PS-A unit
Front of PS-A unit
CF
IDE I/F
PCMCIA I/F
(2 ports)
*1 Built-in accessory only
*2 Digital Electronics Corporation's optional devices and commercial products.
*3 When setting RS-232C mode for COM2.
*4 When setting RS-422 or RS-485 mode for COM2.
Please refer to 1.2 Accessories.
USB I/F
RAS I/F
RAS Cable
(4 ports)
CF Card I/F
(TYPE ll, 1 port)
Speaker Out I/F
Hub
Speaker
PS/2 Keyboard
Central Network Line
Main Memory Module
*1 *2
CF Cards
*2
CF Cards
*2
Main Memory I/F
Peripherals
(commercial type)
Peripherals
(commercial type)
USB 2.0 Compatible Peripherals
(commercial type)
(Produces by users)
USB 2.0 Compatible Peripherals
(commercial type)
PCMCIA Card
(commercial type)
Pin-jack Cable
(commercial type)
LAN1:10BASE-T/100BASE-TX Cable (commercial type)
RS-232C Cable
CF
CF Card Adapter
*2
COM1/COM2
*3
*4
COM2
PS/2 Keyboard I/F
RS-422 Cable
RS-485 Cable
Ethernet I/F
(2 ports)
LAN2:10BASE-T/100BASE-TX/1000BASE-T Cable (commercial type)
USB I/F
(1 port)
*1*2

PS-3710A/PS-3711A Series Hardware Manual
1-4
1.2 Accessories
All accessories listed here are produced by Digital Electronics Corporation.
1.2.1 Option Items
Product Name Model No. Description
DIM module PSA-DDR512 Memory module 512MB
PSA-DDR1G Memory module 1GB
Hard Disk Unit
PS365XA-HD40
HDD Unit mounted a Type 2.5 Parallel
ATA Hard Disk
(40GB minimum without OS)
Applicable Units:
PS3710A-T41,PS3710A-T41-24V,
PS3711A-T41,PS3711A-T41-24V
PS371XA-HD60P
HDD Unit mounted a Type 2.5 Parallel
ATA Hard Disk
(60GB minimum without OS)
Applicable Units:
PS3710A-T42,PS3710A-T42-24V,
PS3711A-T42,PS3711A-T42-24V
SSD Unit PS371XA-SD16P Flash memory unit (16GB without OS)
CF Card
CA3-CFCALL/128MB-01 Type I 128MB
CA3-CFCALL/256MB-01 Type I 256MB
CA3-CFCALL/512MB-01 Type I 512MB
CA6-CFCALL/1GB-01 Type I 1GB
CA8-CFCALL/2GB-01 Type I 2GB
CF Card Adaptor GP077-CFAD10 CF Card Adaptor for a PCMCIA
interface
15-inch Unit Cover Set CA4-CVR15-01 CoverSet for PS-3711A's development
and maintenance use.
15-inch Unit Stand CA4-STD15-01 Stand for PS-3711A's development
and maintenance use.
15-inch Unit Power Supply CA4-PWU15-01 Power Supply for PS-3711A's
development and maintenance use.

Chapter 1 Overview
1-5
1.2.2 Maintenance Items
Product Name Model No. Description
Installation Fastener CA3-ATFALL-01 Used to install the PS-A into a solid
panel (4 pieces/set).
Installation Gasket CA3-WPG15-01 Provides dust and moisture resistance when PS-A is installed into a solid
panel.
Replacement Backlight*1
*1 The appropriate replacement backlight depends on your PS-A model.
CA3-BLU15-01 Applicable Units: PS3710A-T41,PS3710A-T41-24V,
PS3711A-T41,PS3711A-T41-24V
CA7-BLU15-01*2
*2 When LED backlight is used for your PS-A, it is not user-replaceable.
For the backlight type you use, refer to the following information.
• PS-3710A Series "Display Functions" (page2-7)
• PS-3711A Series " Display Functions" (page2-26)
When the LED backlight needs to be replaced, please contact your local PS-A distrib-
utor.
Applicable Units:
PS3710A-T42,PS3710A-T42-24V,
PS3711A-T42,PS3711A-T42-24V
Protective panel sheet CA3-DFS15-01 Disposable sheet that protects the PS- A unit’s screen from dust.
(5 sheets/set) (Hard type)
AC Power Supply
Connector (Straight) CA7-ACCNL-01 AC Power Supply Connector (5 connectors/set)
DC Power Supply
Connector (Straight) CA7-DCCNL-01 DC Power Supply Connector only for
PS-3710A Series
(5 connectors/set)
DC Power Supply
Connector (Right-angle) CA5-DCCNL-01 DC Power Supply Connector only for
PS-3711A Series
(5 connectors/set)