Pro-Form 500 SPX User manual

Model No. PFEX03820.0
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Serial
Number
Decal
USER’S MANUAL
proform.com
To register your product and
activate your warranty today,
go to my.proform.com.
For service at any time, go to
support.proform.com.
Or call 1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER CARE

2
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
EXERCISE GUIDELINES ....................................................................17
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
TABLE OF CONTENTS
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the
front cover of this manual and request a free replacement decal. Apply the decal in the location
shown. Note: The decal(s) may not be shown at actual size.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. It is the responsibility of the owner to
ensure that all users of the exercise bike are
adequately informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. The exercise bike is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they are given supervi-
sion or instruction about use of the exercise
bike by someone responsible for their safety.
4. Use the exercise bike only as described in
this manual.
5. The exercise bike is intended for home use
only. Do not use the exercise bike in a com-
mercial, rental, or institutional setting.
6. Keep the exercise bike indoors, away from
moisture and dust. Do not put the exercise
bike in a garage or covered patio, or near
water.
7. Place the exercise bike on a level surface,
with a mat beneath it to protect the floor or
carpet. Make sure that there is at least 2 ft.
(0.6 m) of clearance around the exercise bike.
8. Inspect and properly tighten all parts each
time the exercise bike is used. Replace any
worn parts immediately.
9. Keep children under age 16 and pets away
from the exercise bike at all times.
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
11. The exercise bike should not be used
by persons weighing more than 250 lbs.
(113 kg).
12. Be careful when mounting and dismounting
the exercise bike.
13. Always keep your back straight while using
the exercise bike; do not arch your back.
14. The exercise bike does not have a freewheel;
the pedals will continue to move until the
flywheel stops. Reduce your pedaling speed
in a controlled way.
15. To stop the flywheel quickly, press the
resistance knob downward.
16. When the exercise bike is not in use, tighten
the resistance knob completely to prevent
the flywheel from moving.
17. To avoid damaging the brake pads, do not
lubricate the brake pads.
18. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.

4
STANDARD SERVICE PLANS

5
Thank you for selecting the new PROFORM®500 SPX
exercise bike. Cycling is an effective exercise for
increasing cardiovascular fitness, building endurance,
and toning the body. The 500 SPX exercise bike
provides a selection of features designed to make your
workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Resistance Knob
Saddle
Adjustment Knobs
Adjustment Knob
Pedal/Strap
Leveling Foot
Leveling Foot
Handlebar
Console
Tablet Holder
BEFORE YOU BEGIN
Wheel
Length: 4 ft. 1 in. (124 cm)
Width: 1 ft. 9 in. (53 cm)

6
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M8 x 55mm Carriage
Bolt (9)–4
M6 x 40mm Screw
(75)–2
M8 Washer
(3)–4
M8 Flange Nut
(2)–4
M8 Locknut
(77)–4
M8 x 16mm
Bolt (76)–4

7
1
• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly
requires the following tool(s):
one adjustable wrench
one rubber mallet
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
ASSEMBLY
2. If there are shipping tubes (not shown) attached
to the front and rear of the Frame (1), remove
and discard the shipping tubes and the hardware
attaching them.
Orient the Front Stabilizer (4) as shown.
Attach the Front Stabilizer (4) to the Frame (1)
with two M8 x 55mm Carriage Bolts (9), two M8
Washers (3), and two M8 Flange Nuts (2).
2
2
9
3
4
1
1. Go to my.proform.com on your computer and
register your product.
• documents your ownership
• activates your warranty
• ensures priority customer support if assistance
is ever needed
Note: If you do not have internet access, call
Customer Care (see the front cover of this
manual) and register your product.

8
2
9
3
32
A
B
5
6
1
1
3
3. Attach the Rear Stabilizer (5) to the Frame (1)
with two M8 x 55mm Carriage Bolts (9), two M8
Washers (3), and two M8 Flange Nuts (2).
4
4. Locate the Adjustment Knob (A) on the rear of
the Frame (1). Loosen the Adjustment Knob,
pull it outward, remove the Saddle Post (6), and
release the Adjustment Knob.
Orient the Saddle Post (6) as shown. Next, pull
the Adjustment Knob (A) outward, insert the
Saddle Post into the Frame (1), move it upward
or downward to the desired position, and then
release the Adjustment Knob into an adjustment
hole in the Saddle Post. Tighten the Adjustment
Knob. Make sure that the Adjustment Knob is
firmly engaged in an adjustment hole.
Orient the Saddle Carriage (32) as shown. Next,
locate the Adjustment Knob (B) on the Saddle
Post (6). Then, loosen the Adjustment Knob, pull
it downward, insert the Saddle Carriage into the
Saddle Post, move it to the desired position, and
then release the Adjustment Knob into an adjust-
ment hole in the Saddle Carriage. Tighten the
Adjustment Knob.

9
5
5. Orient the Saddle (31) as shown.
Slide the Saddle (31) onto the Saddle Carriage
(32); make sure that the Saddle is level and is
pointing straight ahead. Then, tighten the two
nuts (C) beneath the Saddle. 32
C
31
6
15
77
77
72
76
7
1
6. Orient the Handlebar (7) and the Handlebar
Post (72) as shown. Attach the Handlebar to
the Handlebar Post with four M8 x 16mm Bolts
(76) and four M8 Locknuts (77); start all the
Locknuts, and then tighten them.
Next, locate the Adjustment Knob (15) on the
front of the Frame (1). Loosen the Adjustment
Knob and pull it outward. Then, insert the
Handlebar Post (72) into the Frame.
Move the Handlebar Post (72) upward or
downward to the desired position, release
the Adjustment Knob (15) into an adjustment
hole in the Handlebar Post, and then tighten
the Adjustment Knob. Make sure that the
Adjustment Knob is firmly engaged in an
adjustment hole.

10
7. Identify the Right Pedal (11).
Using an adjustable wrench, firmly tighten the
Right Pedal (11) clockwise into the Right Crank
Arm (49).
Firmly tighten the Left Pedal (not shown)
counterclockwise into the Left Crank Arm
(not shown). IMPORTANT: You must turn the
Left Pedal counterclockwise to attach it.
11
7
49
8. The Console (58) can use two AAA batteries (not
included); alkaline batteries are recommended.
Do not use old and new batteries together or
alkaline, standard, and rechargeable batter-
ies together. IMPORTANT: If the Console has
been exposed to cold temperatures, allow
it to warm to room temperature before you
insert batteries. Otherwise, you may damage
the console displays or other electronic com-
ponents. Remove the battery cover, and insert
the batteries into the battery compartment (D).
Make sure to orient the batteries as shown by
the diagram inside the battery compartment.
Then, reattach the battery cover.
8
58
D

11
9
58
7
9. Slide the Console (58) onto the Console
Bracket (10) on the Handlebar (7).
10
10. Hold the wire (E) on the Reed Switch (59) on the
left side of the exercise bike as shown.
Connect the wire (E) on the Reed Switch (59) to
the wire (F) on the Console (58).
F
59
E
10
58

12
11
11. Insert the wire (E) on the Reed Switch (59) into
the Clip (64) on the left side of the Frame (1).
Next, insert the Reed Switch (59) into the Clamp
(30) on the Frame (1).
Then, rotate the Flywheel (37) so that the
Magnet (20) is facing the Reed Switch (59).
See the inset drawing. Move the Reed Switch
(59) so that it is 1/2" (1–2 cm) away from the
Magnet (20).
64
E
37
1
59 20
30 20
59
12
12. Orient the Tablet Holder (73) as shown, and
press it onto the Handlebar (7) in the location
shown. Center the Tablet Holder on the
Handlebar and rotate it forward or backward to
the desired position.
While a second person holds the Tablet Holder
(73) in place, attach the Tablet Holder with
the Clamp Bracket (74) and two M6 x 40mm
Screws (75) as shown in the inset drawing.
74
73
7
75
74
75
73
13. After the exercise bike is assembled, inspect it to make sure that it is assembled correctly and that it
functions properly. Make sure that all parts are properly tightened before you use the exercise bike.
Extra parts may be included. Place a mat under the exercise bike to protect the floor.

13
HOW TO ADJUST THE ANGLE OF THE SADDLE
You can adjust the angle of the saddle to the position
that is most comfortable. You can also slide the saddle
forward or backward to increase your comfort or to
adjust the distance to the handlebar.
To adjust the saddle,
loosen the nuts (A)
on the saddle clamp
a few turns, and then
tilt the saddle upward
or downward or slide
the saddle forward
or backward to the
desired position.
Then, retighten the nuts.
HOW TO LEVEL THE EXERCISE BIKE
If the exercise bike rocks slightly on your floor during
use, turn one or more of the leveling feet on the front
and rear stabilizers (see the drawing on page 5)
until the rocking motion is eliminated.
HOW TO ADJUST THE HORIZONTAL POSITION OF
THE SADDLE
To adjust the position
of the saddle, first
loosen the adjust-
ment knob (B) and
pull it downward.
Then, move the
saddle forward or
backward, release
the adjustment knob
into an adjustment
hole in the saddle
carriage, and firmly
tighten the adjustment knob. Make sure that the
adjustment knob is engaged in an adjustment hole.
HOW TO ADJUST THE SADDLE POST
For effective exercise, the saddle should be at the
proper height. As you pedal, there should be a slight
bend in your knees when the pedals are in the lowest
position.
To adjust the height
of the saddle post,
first loosen the
adjustment knob
(C) and pull it out-
ward. Then, move
the saddle post
upward or downward,
release the adjust-
ment knob into an
adjustment hole in
the saddle post, and
firmly tighten the adjustment knob. Make sure that the
adjustment knob is engaged in an adjustment hole.
HOW TO ADJUST THE HANDLEBAR POST
To adjust the height
of the handlebar
post, first loosen the
adjustment knob (D)
and pull it outward.
Then, move the han-
dlebar post upward
or downward, release
the adjustment knob
into an adjustment
hole in the handlebar post, and firmly tighten the
adjustment knob. Make sure that the adjustment
knob is engaged in an adjustment hole.
A
B
C
D
HOW TO USE THE EXERCISE BIKE

14
HOW TO ADJUST THE PEDALING RESISTANCE
To increase the
resistance of the
pedals, turn the
resistance knob
(E) clockwise; to
decrease the resis-
tance, turn the
resistance knob
counterclockwise.
To stop the flywheel, push the resistance knob
downward. The flywheel should quickly come to a
complete stop.
IMPORTANT: When the exercise bike is not in use,
tighten the resistance knob completely.
HOW TO USE THE TABLET HOLDER
IMPORTANT: The tablet holder (F) is designed
for use with most full-size tablets. Do not place
any other electronic device or object in the tablet
holder.
To insert a tablet
into the tablet holder
(F), set the bottom
edge of the tablet in
the tray. Make sure
that the tablet is
firmly secured in
the tablet holder. To
adjust the position of
the tablet holder, see
assembly step 12 on
page 12. Reverse these actions to remove the tablet
from the tablet holder.
HOW TO MAINTAIN THE EXERCISE BIKE
Regular maintenance is important for optimal
performance and to reduce wear. Inspect and properly
tighten all parts each time the exercise bike is used.
Replace any worn parts immediately.
To clean the exercise bike, use a damp cloth and a
small amount of mild detergent. IMPORTANT: To
avoid damage to the console, keep liquids away
from the console and keep the console out of
direct sunlight.
HOW TO TROUBLESHOOT THE CONSOLE
If the console display becomes dim, replace the
batteries (see assembly step 8 on page 10); most
console problems are the result of low batteries.
If the exercise bike will not be used for an extended
period of time, remove the batteries from the console.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed switch, see assembly step 11
on page 12. Slide the Reed Switch (59) slightly
closer to or away from the Magnet (20). Then, turn the
Flywheel (37) for a moment.
Repeat these actions until the console displays correct
feedback.
E
F

15
FEATURES OF THE CONSOLE
The easy-to-use console features six modes that
provide instant exercise feedback during your
workouts.
Scan (SCAN)—This mode displays the time, speed,
distance, calories, and odometer modes, for a few
seconds each, in a repeating cycle.
Time (TIME)—This mode displays the elapsed time.
Note: If you set a time goal (see step 2 on this page),
this display will show the time remaining in your
workout.
Speed (SPEED)—This mode displays your pedaling
speed, in miles per hour.
Distance (DIS)—This mode displays the distance
that you have pedaled during your workout, in miles.
Note: If you set a distance goal (see step 2 on this
page), this display will show the distance remaining in
your workout.
Calories (CAL)—This mode displays the approxi-
mate number of calories you have burned during your
workout. Note: If you set a calorie-burning goal (see
step 2 on this page), this display will show the number
of calories yet to be burned in your workout.
Odometer (ODO)—This mode displays the total
distance, in miles, that has been pedaled since the
odometer was last reset. Note: To reset the odometer,
remove the batteries from the console and then
reinsert them.
HOW TO USE THE CONSOLE
Make sure that batteries (not included) are installed
in the console (see assembly step 8 on page 10). If
there is a sheet of plastic on the console, remove the
plastic.
1. Turn on the console.
To turn on the console, press any button on the
console or simply begin pedaling.
2. Set a workout goal if desired.
To set a time, distance, or calorie-burning goal for
your workout, press the Mode button repeatedly
until the word TIME, DIS, or CAL appears in the
display. Make sure that the word SCAN does not
appear in the display.
Next, press the Set button repeatedly to set a goal.
To set a goal quickly, hold down the Set button. To
reset the goal, press and hold the Mode button until
zeros appear in the display.
3. Begin pedaling and follow your progress with
the display.
Scan mode—To select the scan mode, press
the Mode button repeatedly until the word SCAN
appears in the display.
Time, speed, distance, calories, or odometer
mode—To select one of these modes for continu-
ous display, press the Mode button repeatedly
until the name of the desired mode appears in the
display. Make sure that the word SCAN does not
appear in the display.
As you exercise, the console will provide instant
feedback about your workout.
When a workout goal is not set, an upward-
pointing arrow will appear in the display when the
time, distance, or calories mode is selected. When
a workout goal is set, a downward-pointing arrow
will appear in the display when the time, distance,
or calories mode is selected.
If you have set a workout goal, the display will
count down and show zeros when you reach your
goal; if you continue to exercise, the display will
begin to count upward.
4. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
console will pause.
The console has an auto-off feature. If the ped-
als do not move and the console buttons are not
pressed for a few minutes, the power will turn off
automatically to save the batteries.

16
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party respon-
sible for compliance could void the user’s authority to operate this equipment.

17
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only
after the first few minutes of exercise does your body
begin to use stored fat calories for energy. If your
goal is to burn fat, adjust the intensity of your exer-
cise until your heart rate is near the lowest number in
your training zone. For maximum fat burning, exercise
with your heart rate near the middle number in your
training zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
HOW TO MEASURE YOUR HEART RATE
To measure your heart
rate, exercise for at least
four minutes. Then, stop
exercising and place
two fingers on your wrist
as shown. Take a six-
second heartbeat count,
and multiply the result
by 10 to find your heart
rate. For example, if your six-second heartbeat count is
14, your heart rate is 140 beats per minute.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretch-
ing and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete
three workouts each week, with at least one day of
rest between workouts. After a few months of regular
exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
WARNING: Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
EXERCISE GUIDELINES

18
PART LIST Model No. PFEX03820.0 R0620A
1 1 Frame
2 4 M8 Flange Nut
3 10 M8 Washer
4 1 Front Stabilizer
5 1 Rear Stabilizer
6 1 Saddle Post
7 1 Handlebar
8 1 Water Bottle Holder
9 4 M8 x 55mm Carriage Bolt
10 1 Console Bracket
11 1 Right Pedal
12 1 Left Pedal
13 2 M12 Flange Nut
14 10 #8 x 20mm Screw
15 3 Adjustment Knob
16 1 Brake Pad Assembly
17 2 M5 Locknut
18 4 M5 Washer
19 2 M5 x 30mm Bolt
20 1 Magnet
21 1 Brake Bracket
22 6 M8 Pulley Locknut
23 1 Brake Cover
24 1 Resistance Knob
25 2 Carriage Sleeve
26 1 Spring
27 1 Square Spacer
28 1 Resistance Spacer
29 1 Carriage Cap
30 1 Clamp
31 1 Saddle
32 1 Saddle Carriage
33 1 3/8" Square Nut
34 1 Drive Pulley
35 1 Crank
36 1 Axle
37 1 Flywheel
38 9 #10 x 12mm Screw
39 1 Outer Guard
40 1 Drive Belt
41 1 Drive Belt Guard Cover
42 1 Inner Guard
43 1 #12 x 15mm Screw
44 1 Brake Bracket Pad
45 2 Crank Cap
46 2 M8 x 18mm Screw
47 1 Left Crank Arm
48 2 Crank Bearing
49 1 Right Crank Arm/Sprocket
50 2 M6 x 40mm Bolt
51 2 Frame Sleeve
52 2 Wheel
53 2 M6 Locknut
54 2 M8 Nut
55 4 Leveling Foot
56 2 M8 x 55mm Bolt
57 4 3/8" Nut
58 1 Console
59 1 Reed Switch/Wire
60 1 M5 x 12mm Screw
61 1 Brake Cover Spacer
62 4 M6 Washer
63 1 Console Bracket Screw
64 1 Clip
65 2 Snap Ring
66 2 M12 Jam Nut
67 1 Axle Spacer
68 2 Flywheel Bearing
69 4 M12 Large Washer
70 6 M8 x 20mm Screw
71 2 M8 x 10mm Screw
72 1 Handlebar Post
73 1 Tablet Holder
74 1 Clamp Bracket
75 2 M6 x 40mm Screw
76 4 M8 x 16mm Bolt
77 4 M8 Locknut
* – Assembly Tool
* – User’s Manual
Key No. Qty. Description Key No. Qty. Description
Note: Specications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.

19
EXPLODED DRAWING Model No. PFEX03820.0 R0620A
1
3
8
12
5
2
911
15
15
34
38
38
38
38
38
38
39
35
40
14
14
14
41
43
46
46
45
45
42
47
49
54
56
55
57
20
14
30
48
48
65
65
7
51
14
3
3
3
62
62
3
2
450
52
22
53
9
16
18
18 18
18
19
17
14
21
26
28
27
33
44
14
61
14
23
24
6
15
25
32
25
29
31
51
60
74
75
76
76
77
77
64
13
13
69
69
36
37
66
67
68
68
69
66
10
58
59
72
73
63
70
70
71
22

Part No. 425171 R0620A Printed in China © 2020 ICON Health & Fitness, Inc.
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
ORDERING REPLACEMENT PARTS
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for ve (5) years from the date
of purchase. Parts and labor are warranted for ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser (customer) and is not transferrable. ICON’s obliga-
tion under this warranty is limited to repairing or replacing, at ICON’s option, the product through one of
its authorized service providers. All repairs for which warranty claims are made must be preauthorized by
ICON. If replacement parts are shipped while the product is under warranty, the customer will be respon-
sible for a minimal handling charge. For in-home service, the customer may be responsible for a minimal
trip charge. This warranty does not extend to freight damage to the product. This warranty will automati-
cally be voided by the following conditions: (1) if the product is used as a store display model, (2) if the
product is purchased or transported outside the USA, (3) if all instructions and warnings in this manual are
not followed, (4) if the product is abused or improperly or abnormally used, or (5) if the product is used for
commercial or rental purposes. No other warranty beyond that specically set forth above is authorized
by ICON.
ICON is not responsible or liable for the following damages: (1) indirect, special, or consequential dam-
ages arising out of or in connection with the use or performance of the product; (2) damages with respect
to any economic loss, loss of property, loss of revenues or prots, loss of enjoyment or use, or costs of
removal or installation; or (3) other consequential damages of any kind. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not
apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or tness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer. This warranty provides specic legal rights; the customer
may have other rights that vary from state to state.
For warranty service, please call the telephone number on the front cover of this manual. Please be pre-
pared to provide the model number and serial number of the product (see the front cover of this manual).
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
LIMITED WARRANTY
IMPORTANT: To protect your fitness equipment with an extended service plan, see page 4.