Pro-Form 831.21941.2 User manual

Model No. 831.21941.2
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal (under frame)
•Assembly
• Operation
•Maintenance
•Part List and Drawing
Sears, Roebuck and Co.
Hoffman Estates, IL 60179
BIKE EXERCISER
User's Manual

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................... 2
IMPORTANT PRECAUTIONS .................................................................. 3
BEFORE YOU BEGIN ........................................................................ 4
PART IDENTIFICATION CHART ................................................................ 5
ASSEMBLY ................................................................................ 6
HOW TO USE THE EXERCISE BIKE ........................................................... 12
FCC INFORMATION ........................................................................ 18
MAINTENANCE AND TROUBLESHOOTING .................................................... 19
EXERCISE GUIDELINES .................................................................... 21
PART LIST ................................................................................ 22
EXPLODED DRAWING ...................................................................... 23
ORDERING REPLACEMENT PARTS ................................................... Back Cover
90 DAY FULL WARRANTY ........................................................... Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s), if adecal is missing or illegible, call
1-888-533-1333 and request a free replacement
decal. Apply the decal in the location shown.
Note: The decal(s) may not be shown at actual size.
,Misuseof this machine
may result in serious
injury.
.Read user's manual
prior to use and foflow
all warnings and
instructions,
• Do not allow children
on oraround machine.
•Pedals continue to
spin when you stop
pedaling.
=Spinning `pedals can
cause injury.
•Reduce pedal speed
in acontrolledmanner.
• User weight must not
exceed 250 pounds.
• Replace label if
damaged, illegible, or
removed. [_
2

iMPORTANT PRECAUTIONS
3

BEFORE YOU BEGIN
Thank you for selecting the new PROFORM '_'XP 210
U exercise bike. Cycling is an effective exercise for
increasing cardiovascular fitness, building endurance,
and toning the body. The XP 210 U exercise bike
provides a selection of features designed to make your
workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions after
reading this manual, please see the back cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 3 ft. 7 in. (109 cm)
Width: 2 ft. (61 cm)
Console Heart Rate
Monitor
Handlebar
Water Bottle Holder*
Seat Knob
Seat PostKnob Pedal
Wheel
Leveling Foot *Water bottle is not included
4

PART iDENTiFiCATiON CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included, if a part is missing, please call 1-888-533-1333.
M4 x 16mm
Screw (40)-6 M4 x 22mm
Screw (54)-2 M8 x 25mm Button
Screw (44)-6
M10 x 80mm Button
Screw (36)-2
M8 x 60mm Button
Screw (43)-4
M8 Split Washer
(45)-6
5

ASSEMBLY
Assembly requires two persons.
Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you complete all assembly steps.
To identify small parts, see page 5.
In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver (]_z;======_
one adjustable wrench
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
.Orient the Rear Stabilizer (14) as shown. While
a second person lifts the rear of the Frame (1),
insert the Rear Stabilizer into the Frame.
Attach the Rear Stabilizer (14) with four M8 x
60mm Button Screws (43).
14 1.-.
43
.Orient the Front Stabilizer (2) as indicated by the
sticker.
While a second person lifts the front of the
Frame (1), attach the Front Stabilizer (2) to the
Frame with two M10 x 80mm Button Screws
(36).
36
6

,Orient the Upright (3) as shown. Have a second
person hold the Upright near the Frame (1).
Locate the wire tie in the lower end of the Upright
(3). Tie the wire tie to the Main Wire (31). Then,
pull the upper end of the wire tie until the Main
Wire is routed through the Upright.
Tip: To prevent the Main Wire (31) from fall-
ing into the Upright (3), secure the Main Wire
with the wire tie.
Wire Tie
3__/
Wire Tie
,Tip: Avoid pinching the Main Wire (31). Set
the Upright (3) on the Frame (1).
Attach the Upright (3) with four M8 x 25mm
Button Screws (44) and four M8 Split Washers
(45). Tip: Start all the Button Screws before
fully tightening them. Avoid pinching the
Main Wire (31)
31
44 44
7

.Orient the Top Shield (9) as shown. Slide the Top
Shield onto the Upright (3).
Attach the Top Shield (9) to the Frame (1) with
two M4 x 16mm Screws (40).
Orient the Top Shield Cap (10) as shown. Press
the Top Shield Cap onto the Left and Right
Shields (17, 18).
17,
10
40 9
.Orient the Seat (12) and the Seat Carriage (30)
as shown. Attach the Seat to the Seat Carriage
with four M8 Locknuts (37), four M8 Split
Washers (45), and four M8 Washers (56).
12
56 _56
45_ '_3 _5
37 7
8

.Loosen and remove the Seat Knob (11) from the
Seat Carriage (30).
Look underneath the Seat (12), and locate the
Carriage Block (55) inside the Seat Carriage
(30).
Orient the Seat Post (5) as shown. Set the Seat
Carriage (30) in the bracket on the Seat Post.
Next, insert the Seat Knob (11) upward through
the bracket on the Seat Post (5) into the hole in
the Carriage Block (55). Then, tighten the Seat
Knob.
12
.Loosen and remove the Seat Post Knob (48)
from the Frame (1).
Next, insert the Seat Post (5) into the Frame (1),
and press the Seat Post Bushing (20) downward
into the Frame.
Slide the Seat Post (5) upward or downward to
the desired position, and then insert the Seat
Post Knob (48) into the Frame and into one of
the adjustment holes in the Seat Post. Then,
tighten the Seat Post Knob. Adjustment
Holes
20
9

,Orient the Console Plate (19) and the Handlebar
(47) as shown. Have a second person hold
the Console Plate and the Handlebar near the
Upright (3).
Locate the Pulse Wire (52) in the Handlebar
(47). Insert the Pulse Wire into the hole in the
Upright (3), and then pull it upward out of the top
of the Upright.
Then, insert the Main Wire (31) and the Pulse
Wire (52) upward through the Console Plate
(19).
47---.
31\19
10. Tip: Avoid pinching the wires. Insert the
Console Plate (19) into the Upright (3).
Attach the Handlebar (47) and the Console
Plate (19) to the Upright (3) with two M8 x 25mm
Button Screws (44) and two M8 Split Washers
(45).
10
Avoid pinching
the wires 19
45
11. The Console (6) can use four D batteries
(not included); alkaline batteries are recom-
mended, iMPORTANT: if the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before insert=
ing batteries. Otherwise, you may damage
the console displays or other electronic
components.
Remove the screws and the battery covers
from the back of the Console (6), and insert
batteries into the battery compartments. Make
sure to orient the batteries as shown by the
diagrams inside the battery compartments.
Then, reattach the battery covers.
To purchase an optional power adapter, call
the telephone number on the cover of this
manual. To avoid damaging the console, use
only a manufacturer=supplied power adapter.
Plug one end of the power adapter into the
receptacle on the console; plug the other end
into an outlet installed in accordance with all
local codes and ordinances.
11
Battery
Cover
6\
y
Cover
10