Pro-Form 831.297980 User manual

USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial
Number
Decal
Model No. 831.297980
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
®

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
®
2

3
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10. When connecting the power cord (see page 7),
plug the power cord into a surge protector
(not included) and plug the surge protector
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.
11. Use only a single-outlet surge suppressor
that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppres-
sor must have a UL suppressed voltage rating
of 400 volts or less and a minimum surge dis-
sipation of 450 joules. The surge suppressor
must be electrically rated for 120 volts AC and
15 amps.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
16. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO MOVE
THE TREADMILL on page 13.) You must be
able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
DANGER:To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS

21. Inspect and tighten all parts of the treadmill
regularly.
22. Never drop or insert any object into any
opening.
23. DANGER:Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right and
below have been placed on your
treadmill. If one of the decals is miss-
ing, or if it is not legible, please call
our toll-free HELPLINE to order a free
replacement decal (see the back
cover of this manual). Apply the decal
in the location shown.
4

Thank you for selecting the new PROFORM®J8 tread-
mill. The J8 treadmill combines advanced technology
with innovative design to let you enjoy an excellent
form of cardiovascular exercise in the convenience and
privacy of your home. And when you’re not exercising,
the unique J8 can be folded up, requiring less than half
the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our toll-free HELPLINE at 1-800-736-6879,
Monday through Saturday, 7 a.m. until 7 p.m. Central
Time (excluding holidays). To help us assist you,
please note the product model number and serial num-
ber before calling. The model number of the treadmill
is 831.297980. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
BEFORE YOU BEGIN
Handrail
Hand Weight Holder*
Accessory Holder
*Optional hand weights add upper-body exercise to your workouts. To order hand weights, see the back
cover of this manual.
Storage Latch
Pulse
Sensor
Book Holder
Key/Clip
Circuit
Breaker
On/Off Switch
Walking Belt
Cushioned Walking Platform
Front
Wheel
Foot Rails
Power
Cord
Rear Roller
Adjustment Bolts
Water Bottle
Holder (Bottle
not included)
RIGHT SIDELEFT SIDE
5

ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. No tools are required for assembly.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
Uprights (15) until the treadmill is in the position shown.
2. If the Handrail Grips (91) are not attached, slide a
Handrail Grip onto the square tube on the left Upright
(15). Attach the Handrail Grip with two Fasteners (63).
Attach the other Handrail Grip (not shown) to the right
Upright. Note: Extra Fasteners may be included.
If the Handrail Grips (91) do not touch the Uprights (15),
squeeze the Handrail Grips and press them towards the
Uprights repeatedly until the Handrail Grips touch the
Uprights.
Next, make sure the Lock Knob Sleeve (93) is fully in-
serted into the left Upright (15). Remove the Lock Knob
(92) from the Lock Pin (97). Make sure that the Lock Pin
Collar (95) and the Spring (94) are on the Lock Pin.
Insert the Lock Pin into the left Upright (15) and tighten
the Lock Knob onto it.
3. Remove the backing from the Adhesive Clip (29). Press
the Adhesive Clip onto the base of one of the Uprights
(15). Press the Allen Wrench (24) into the Adhesive Clip.
4. Make sure that all parts are tightened before you use the treadmill. Place a mat under the treadmill to
protect the floor or carpet.
15
1
95
97
93
94
91
63
92
15
2
24
15 29
3
6

7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Surge suppressors are sold at most hardware stores
and department stores. Use only a single-outlet surge
suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must
have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER:Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin

8
CONSOLE DIAGRAM
Clip
Key
DisplaysDisplays LED Track
Program Indicators Program Indicators
Manual Indicator
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts. When the manual mode is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, an LED “track”
and four displays will provide continuous exercise feed-
back. With the built-in pulse sensor, you can even
measure your heart rate.
In addition, the console offers six workout programs.
Three programs automatically control the incline of the
treadmill and three programs control the speed of the
treadmill as they guide you through effective workouts.
STEP-BY-STEP CONSOLE OPERATION
Note: The treadmill console can display speed and
distance in either miles or kilometers (see SPEED/
PACE DISPLAY on page 9). For simplicity, all instruc-
tions in this section refer to miles.
Before operating the
console, make sure that
the on/off switch, lo-
cated near the power
cord, is in the on posi-
tion.
Next, plug in the power cord (see HOW TO PLUG IN
THE POWER CORD on page 7). Note: If the key is in
the console, remove it before plugging in the power
cord.
Step onto the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above), and slide
the clip onto the waistband of your clothing. Follow the
steps below to operate the console.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
A moment after the
key is inserted, the
four displays and
various indicators
will light.
1
CAUTION:Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turn-
ing on the power.
• Always wear the clip (see the drawing above)
while operating the treadmill. If the key is
pulled from the console, the walking belt will
automatically stop.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console, and place only a sealed
water bottle in the water bottle holder.
On
Position
Note: If there is a sheet of clear plastic
on the face of the console, remove it.

9
Select the manual mode.
When the key is
inserted, the manual
mode will be selected,
as shown by the
manual indicator. If
you have selected a
workout program,
press the mode button repeatedly until the manual
indicator lights.
Press the START button and adjust the speed
of the walking belt.
A moment after the START button is pressed, the
walking belt will begin to move. Hold the handrails
and carefully begin walking.
As you exercise, change the speed of the walking
belt as desired by pressing the SPEED buttons.
Each time one of the buttons is pressed, the
speed will change by 0.1 mph. The buttons can be
held down to change the speed setting quickly.
Note: It may take a few seconds for the walking belt
to reach the selected speed setting.
To stop the walking belt, press the STOP button.
The TIME/INCLINE display will begin to flash. To
restart the walking belt, press the START button
again. To stop the walking belt and reset the dis-
plays, hold down the STOP button for two seconds.
Adjust the incline of the treadmill as desired
To change the incline of the treadmill, press the
INCLINE buttons. Each time one of the buttons is
pressed, the incline will change by 0.5%. The but-
tons can be held down to change the incline
quickly. Note: It may take a few seconds for the
treadmill to reach the selected incline setting.
Follow your progress with the LED track and
the four displays.
The LED Track—
The LED track repre-
sents a distance of
1/4 mile. As you exer-
cise, the indicators
around the track will
light one at a time
until you have com-
pleted 1/4 mile. A new lap will then begin.
DISTANCE/LAPS
display—This display
shows the distance that
the walking belt has
moved and the number
of 1/4-mile laps you have
completed. The display will alternate between one
number and the other every seven seconds; the
indicator will light when the number of laps is
shown.
TIME/INCLINE
display—This display
shows the elapsed time
and the incline level of
the treadmill. The display
will alternate between
one number and the other every seven seconds;
the indicator will light when the incline is shown.
Note: When a workout program is selected, the
display will show the time remaining in the program.
CALS/FAT CALS/
PULSE display—This
display shows the ap-
proximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 16). Every seven sec-
onds, the display will change from one number to
the other; the indicator will light when the number
of fat calories is shown. This display will also
show your heart rate when the pulse sensor is
used (see step 6).
SPEED/PACE
display—This display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
mile ). Every seven seconds, the display will
change from one number to the other; the indicator
will light when your pace is shown.
Note: The console can
display distance, speed
and pace in either miles
or kilometers. To see
which unit of measure-
ment is selected, hold
down the STOP button while inserting the key into
the console. An “E,” for english miles, or an “M,”
for metric kilometers, will appear in the CALS/FAT
CALS/PULSE display. If you want to change the
unit of measurement, press the SPEED ▲▲ button.
Remove and then reinsert the key.
5
4
3
2
Indicator

10
Measure your heart rate, if desired.
Stand on the
foot rails and
place your
hands on the
metal contacts
on the handrail.
Your palms
must be resting
on the upper
contacts, and
your fingers must
be touching the
lower contacts—
avoid moving your hands. When your heart rate
is detected, the heart-shaped indicator in the
CALS/FAT CALS/PULSE display will flash
steadily and a “P” will appear. After a few sec-
onds, your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
When you are finished exercising, press the
STOP button and remove the key.
Step onto the foot rails, press the STOP button
and remove the key from the console. Keep the
key in a secure place.
In addition, move the on/off switch to the off posi-
tion and unplug the power cord.
HOW TO USE THE WORKOUT PROGRAMS
Insert the key into the console.
A moment after the key is inserted, the four dis-
plays and various indicators will light.
Press the MODE button to select the desired
workout program.
When the key is inserted, the manual mode will be
selected, as shown by the manual indicator.
To select one of
the workout
programs,
press the mode
button repeat-
edly until one of
the three incline
program indica-
tors or one of the three speed program indicators
lights.
Note: The two AEROBIC programs are twenty
minutes long; the four FAT BURN programs are
thirty minutes long. The graphs on the sides of the
console show how the incline or speed of the
treadmill will change during the programs. During
the AEROBIC programs, for example, the incline
or speed will gradually increase during the first ten
minutes and then gradually decrease during the
last ten minutes. Each program begins with a
warm-up period and ends with a cool-down period.
Set a maximum incline or speed setting.
If you selected an
incline program, a
number will flash in the
TIME/INCLINE display.
This number is the maxi-
mum incline that the
treadmill will reach during the selected program. If
you want to change the maximum incline setting,
press the INCLINE ▲▲ button. The maximum incline
setting can be from 4% to 10%. If the setting is in-
creased, the difficulty level of the entire program
will increase. If the setting is decreased, the diffi-
culty level of the entire program will decrease.
If you selected a speed
program, a number will
flash in the SPEED/
PACE display. This
number is the maximum
speed that the walking
belt will reach during the selected program. If you
want to change the maximum speed setting, press
the SPEED ▲▲ button. The maximum speed setting
can be from 4 mph to 10 mph. If the setting is in-
creased, the difficulty level of the entire program
will increase. If the setting is decreased, the diffi-
culty level of the entire program will decrease.
Press the START button to start the program
A moment after the START button is pressed, the
walking belt will begin to move. Hold the handrails
and carefully begin walking.
If an incline program is selected: The incline of
the treadmill will change automatically during the
program as shown by the graphs on the left side of
the console. The speed of the walking belt can be
changed by pressing the SPEED buttons. The time
remaining in the program will be shown in the
TIME/INCLINE display. When the program is com-
pleted, the walking belt will slow to a stop.
4
3
2
1
7
6
Metal Contacts
Program Indicators

9
11
If the program is too dif-
ficult or too easy, the
difficulty level of the pro-
gram can be adjusted.
Press the INCLINE ▲▲ or
▼▼ button. A number will
begin to flash in the TIME/INCLINE display. This
number is the maximum incline that the treadmill
will reach during the program. Press the INCLINE
▲▲ or ▼▼ button repeatedly to change the maximum
incline setting. If the setting is increased, the diffi-
culty level of the entire program will increase; if the
setting is decreased, the difficulty level of the entire
program will decrease.
To stop the program for a moment, press the
STOP button. The TIME/INCLINE display will
begin to flash. To restart the program, press the
START button again. To stop the program and
reset the displays, hold down the STOP button for
two seconds. Note: Pressing the MODE button will
also stop the program, reset the displays and se-
lect a different mode.
If a speed program is selected: The speed of the
walking belt will change automatically during the
program as shown by the graphs on the right side
of the console. The incline of the treadmill can be
changed by pressing the INCLINE buttons. The
time remaining in the program will be shown in the
TIME/INCLINE display. When the program is com-
pleted, the walking belt will slow to a stop.
If the program is too dif-
ficult or too easy, the
difficulty level of the pro-
gram can be adjusted.
Press the SPEED ▲▲ or
▼▼ button. A number will
begin to flash in the SPEED/PACE display. This
number is the maximum speed that the treadmill
will reach during the program. Press the SPEED ▲▲
or ▼▼ button repeatedly to change the maximum
speed setting. If the setting is increased, the diffi-
culty level of the entire program will increase; if the
setting is decreased, the difficulty level of the entire
program will decrease.
To stop the program for a moment, press the
STOP button. The TIME/INCLINE display will
begin to flash. To restart the program, press the
START button again. To stop the program and
reset the displays, hold down the STOP button for
two seconds. Note: Pressing the MODE button will
also stop the program, reset the displays and se-
lect a different mode.
Follow your progress with the LED track and
the four displays.
See step 5 on page 9.
Measure your heart rate, if desired.
See step 6 on page 10.
When the program is completed, remove the
key.
Step onto the foot rails and remove the key from
the console. Keep the key in a secure place.
In addition, move the on/off switch to the off posi-
tion and unplug the power cord.
THE INFORMATION MODE
To access the information mode, hold down the STOP
button while inserting the key into the console.
The DISTANCE/LAPS
display will show the total
number of miles that the
walking belt has moved.
The TIME/INCLINE display
will show the total number of
hours the treadmill has been
used.
An “E,” for english miles, or
an “M,” for metric kilometers,
will appear in the CALS/FAT
CALS/PULSE display. If you
want to change the unit of
measurement, press the
SPEED ▲▲ button.
To exit the mode, remove the key from the console.
7
6
5

THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, please see the back
cover of this manual.
THE OPTIONAL HAND WEIGHTS
Optional hand weights
let you include upper-
body exercise in your
workouts. The hand
weights fit into conve-
nience holders in the
console. To purchase
the optional hand
weights, please see
the back cover of this
manual.
12
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord. CAU-
TION: You must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at
the right. CAUTION: To decrease the possibility of injury,
bend your legs and keep your back straight. As you
raise the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the hole in the catch. Insert the latch pin into
the catch. Make sure that the latch pin is fully inserted
into the catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° Fahrenheit.
Latch
Knob
Pin
Catch
Closed
Open

HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch pin is
fully inserted into the catch.
1. Hold the handrails as shown and place one foot against a
wheel. Do not hold or push on the book holder or the
book holder may be damaged.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving the
treadmill. Do not attempt to move the treadmill over an
uneven surface.
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past
the pin. Slowly release the latch knob.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. CAUTION: To decrease the possibil-
ity of injury, bend your legs and keep your back straight.
Book Holder
Base
Front Wheels
Latch
Knob
Pin
Closed
Open
13

14
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at
1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged
into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449
listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed
voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor
must be electrically rated for 120 volts AC and 15 amps.
b. After the power cord has been plugged in, make sure that the key is inserted into the console as far as it will
go. See step 1 on page 8.
c. Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
d. Check the on/off switch located on the treadmill near the
power cord. The switch must be in the on position.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit
breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 10.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our toll-free HELPLINE.
3. SYMPTOM: THE PULSE SENSOR DOES NOT FUNCTION PROPERLY
a. Make sure to stand on the foot rails and avoid moving your hands while measuring your heart rate.
Excessive movement may interfere with heart rate readings. If the pulse sensor is not used correctly, your
heart rate will not be shown.
b. Do not hold the metal contacts too tightly; doing so may interfere with heart rate readings.
c. For the most accurate heart rate reading, hold the contacts for about 15 seconds.
d. For optimal performance of the pulse sensor, keep the contacts clean. The contacts can be cleaned with a
soft cloth—never use alcohol, abrasives, or chemicals.
Tripped
Reset
Tripped
c
Reset
On
Position
d

4. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
a. Remove the key from the console and UNPLUG THE POWER
CORD. Remove the screws from the hood. Carefully remove the
hood. Locate the Reed Switch (26) and the Magnet (107) on the
left side of the Pulley (12). Turn the Pulley until the Magnet is
aligned with the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 1/8”. If necessary,
loosen the Reed Switch Screw (109) and move the Reed Switch
slightly. Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct speed reading.
5. SYMPTOM: The walking belt slows when walked on
a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. If the walking belt is overtightened, treadmill performance may
decrease and the walking belt may be permanently damaged.
Remove the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts counterclock-
wise, 1/4 of a turn. When the walking belt is properly tightened,
you should be able to lift each side of the walking belt 3 to 4
inches off the walking platform. Be careful to keep the walking
belt centered. Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is prop-
erly tightened.
c. If the walking belt still slows when walked on, please call our toll-
free HELPLINE.
6. SYMPTOM: The walking belt is off-center
a. If the walking belt has shifted to the left, first remove the key and
UNPLUG THE POWER CORD. Using the allen wrench, turn the
left rear roller adjustment bolt clockwise, and the right bolt coun-
terclockwise, 1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is cen-
tered.
b. If the walking belt has shifted to the right, first remove the key
and UNPLUG THE POWER CORD. Using the allen wrench, turn
the left rear roller adjustment bolt counterclockwise, and the right
bolt clockwise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the walking belt is
centered.
7. SYMPTOM: The walking belt slips when walked on
a. If the walking belt slips when walked on, first remove the key and
UNPLUG THE POWER CORD. Using the allen wrench, turn
both rear roller adjustment bolts clockwise, 1/4 of a turn. When
the walking belt is correctly tightened, you should be able to lift
each side of the walking belt 3 to 4 inches off the walking plat-
form. Be careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
3”–4”
b
b
a
a
107
26
109
Top
View
1/8” 12
15

16
CONDITIONING GUIDELINES
The following guidelines will help you to plan your ex-
ercise program. Remember—these are general guide-
lines only. For more detailed exercise information, ob-
tain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone. It may also be helpful to use one of
the console’s FAT BURN programs (see pages 10 to 13).
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone. It may also be helpful to use one of the console’s
AEROBIC programs (see pages 10 to 13).
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
WARNING:Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.

14
17
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for each leg. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
1
2
3
4
5

18
PART LIST—Model No. 831.297980 R0399A
1 2 Center Track
2 2 Foot Rail
3 1 Left Foot Rail Cap
4 1 Front Roller Adjustment Nut
5 4 Isolator
6 6 Bumper
7 6 Platform Screw
8 1 Walking Platform
9 2 Frame Pivot Bolt
10 2 Frame Pivot Spacer
11 1 Walking Belt
12 1 Front Roller/Pulley
13 28 Small Screw
14 1 Motor Belt
15 1 Base
16 1 Incline Frame
17 2 Hood Bracket (long)
18 3 Bracket Clip
19 4 Small Screw
20 1 Console Plate
21 8 Nut
22 1 Lift Motor Shield
23 2 Incline Motor Bolt
24 1 Allen Wrench
25 1 Incline Motor
26 1 Reed Switch
27 1 Upright Plug
28 1 Upright Ground Screw
29 1 Adhesive Clip
30 2 Wheel Bolt
31 2 Front Wheel
32 1 Hood Bracket (short)
33 1 Motor Pivot Nut
34 1 Pulley/Flywheel/Fan
35 1 Motor
36 3 Motor Tension Bolt
37 1 Motor Tension Washer
38 1 Star Washer
39 1 Motor Tension Nut
40 1 Motor Pivot Bolt
41 1 Motor Hood
42 1 Incline Motor Shield
43 2 Incline Pivot Washer
44 3 Adj. Washer
45* 1 Motor/Pulley/Fly./Fan
46 1 Front Roller Adj. Bolt
47 1 Choke
48 1 Electronics Bracket
49 1 Controller
50 1 Electronics Shield
51 1 Power Supply
52 4 Plastic Stand-off
53 1 Power Cord
54 1 Grommet
55 1 On/Off Switch
56 1 Circuit Breaker
57 1 Outlet Bracket
58 1 Book Rack
59 2 Belt Guide
60 1 Shock
61 1 Front Belly Pan
62 1 Right Foot Rail Cap
63 26 Belly Pan Fastener
64 1 Console Base
65 2 Frame Guide Screw
66 1 Frame Guide
67 2 Rear Isolator
68 1 Belly Pan
69 0 Not Used
70 4 Hood Screw
71 1 Key/Clip
72 2 Rear Endcap Bracket
73 1 Rear Endcap
74 2 Rear Endcap Pad
75 7 Endcap Screw/Ground Screw
76 2 Rear Roller Adj. Bolt
77 2 Caution Decal
78 1 Latch Decal
79 1 Frame
80 2 Rear Deck Screw
81 1 Console
82 1 Latch Catch
83 1 Rear Roller
84** 1 Optional Hand Weight/Chest Pulse
85 1 Cable Tie
86 2 Cable Tie Screw
87 2 Cable Tie Clamp
88 2 8” Cable Tie
89 5 4” Cable Tie
90 1 Upright Wire Harness
91 2 Handrail Grip
92 1 Lock Knob
93 1 Lock Knob Sleeve
94 1 Spring
95 1 Lock Pin Collar
96 1 Pin Clip
97 1 Lock Pin
98 1 8” Wire Harness
99 4 Pulse Sensor Plate
100 1 Ground Wire
Key
No. Qty. Description Key No. Qty. Description
To identify parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.

Key
No. Qty. Description Key No. Qty. Description
101* 1 Pulse Bar
102 32 Screw
103 2 Pulse Bar Washer
104 2 Pulse Bar Bolt
105 4 Upright Endcap
106 1 Upright Grommet
107 1 Magnet
108 1 Incline Motor Spacer
109 1 Reed Switch Screw
110 1 Reed Switch Clip
111 2 Endcap Spacer
112 1 Optic Switch Nut
113 1 Optic Switch Washer
114 1 Optic Switch Bolt
115 1 Optic Switch
116 1 Incline Disk
# 1 14” White Wire, 2 F
# 1 8” White Wire, M/F
# 1 4” White Wire, M/F
# 1 4” Black Wire, 2 F
# 1 4” Black Wire, M/Ring
# 1 9” Black Wire, M/F
# 1 8” Blue Wire, 2 F
# 1 8” Red Wire, M/F
# 1 8” Green Wire, F/Ring
# 1 User's Manual
# These parts are not illustrated
* Includes all parts shown in the box
** For more information about the optional pulse kit
and weights, see page 12.
Specifications are subject to change without notice. For information about ordering replacement parts, see the
back cover of this manual.
19

61
13
13
13 13
2
10
79
67
76
44
75
74 76
75
74
44 73
63
63
68 67
78
63
2
102 513
63
63
79
9
102
5
102 82
811
12
21
14
73637 38 39
33
40
10
36
34
21
17
13
18
16
21
13
13 18
21
44
46
80
35
13 56
53
54
57
13
13
48
13
47
80
7
7
49
59
69
19
72
19
72
75
100
83
45*
51
52
52
55
21
1
3
28
28
62
1
6
5
18
32
17
4
5
102
109
110
26
107
50
63
63
63
111
111
65
66
36
108 21
25
114
115
116
112
113
EXPLODED DRAWING—Model No. 831.297980 R0399A