PRO SIGNAL PSG3532 User manual

PSG3532
4x4 HDMI 2.0 MATRIX SWITCH 4K 60Hz
1
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

WHAT’s IN THE BOX
OVERVIEW
IMPORTANT SAFETY INFORMATION
• This is a 4 in 4 out HDMI matrix switch, it can switch 4 HDMI input signals to 4 HDMI
displays as required.
• Support up to 4096x2160@60Hz resolution and is backward compatible.
• Support HDR10.
• Support multiple switching mode: IR remote control, buttons and RS232.
• Support setting the EDID of the product.
• Any two of the four HDMI outputs support Auto Down-scaling.
• Lightning protection, surge protection, ESD protection.
• 1x HDMI Matrix Switcher
• 1x 5V 1A Power Supply Unit
• 1x Remote Control
• 1x User Manual
• 2x Mounting brackets and screws
• 1x Terminal block
1. Power Indicator - illuminates when
power is connected
2. IR remote receiving sensor
3. RS232 connection
4. EDID DIP switches
5. HDMI input indicator LEDs
6. Selector switches
7. DC input jack 5V DC 1A
8. HDMI input connectors
9. HDMI output connectors
Please read these instructions carefully before use and retain for future reference.
When using electrical appliances basic safety precautions should always be followed.
• To prevent fire or shock hazard, do not expose this product to rain or moisture.
• For indoor use only.
• Check that the power supply matches the mains voltage.
• Only use the power supply provided or one of identical specification.
• Ensure adequate ventilation and do not obstruct ventilation slots.
FEATURES
2

3
INSTALLATION
OPERATION
• Please make sure all devices you wish to connect have been powered off.
• Connect the source devices to the HDMI input ports with HDMI cables.
• Connect the display devices to the HDMI output ports with HDMI cables.
• Power on the devices to get started.
• Connect the 5V 1A PSU supplied with the HDMI switch to the power input jack and
connect to a mains outlet and turn the power on. The Power LED will illuminate.
• Power on the source and receiving devices.
RS-232 control
• Baud rate: 9600
• Data bits: 8
• Stop character: 1 Parity: none
Operation
Mode 1
HDMI
Input 1
HDMI
Input 2
HDMI
Input 3
HDMI
Input 4
HDMI Output 1 PS11R PS12R PS13R PS14R
HDMI Output 2 PS21R PS22R PS231R PS24R
HDMI Output 3 PS31R PS32R PS33R PS34R
HDMI Output 4 PS41R PS42R PS43R PS44R
HDMI Output
1/2/3/4 PAIR PA2R PA3R PA4R

Operation
Mode 2
Return
Value
Reset Device restart
Recover Restore device factory setting
BaudXX Set baud rate value 9600 (default), 19200
PAPXPXPXPX
Prex 1 2 3 4
Content for output port HDMI 4
Content for output port HDMI 3
Content for output port HDMI 2
Content for output port HDMI 1
PAPXPXPXPX
PA is the command prex, and the “X” of PX can be any number from 1 to 4.
P1 represents HDMI 1 source content for output, P2 represents HDMI 2 source
content for output, and so on to P4.
E.g. PAP3P1P4P2 represents:
Output port HDMI 1 outputs content from input port HDMI 3
Output port HDMI 2 outputs content from input port HDMI 1
Output port HDMI 3 outputs content from input port HDMI 4
Output port HDMI 4 outputs content from input port HDMI 2
PAXXXR is the command to read the status of all interfaces; after sending the
command, OKPXPXPXPX is displayed, where X is 1 to 4; if the command sent is
incorrect, ERR appears.
EDID settings
The product has 16 built-in EDID states, which can be set to switch the output resolution
through the DIP switch. The DIP switch up for “1” and down for “0”.
Dip Switch Status
Resolution Information
1234
00004K@60Hz 2CH
10004K@60Hz 5.1CH
01004K@60Hz 7.1CH
0 0 1 0 4K@60Hz HDR 7.1CH
00014K@30Hz 2CH
11004K@30Hz 5.1CH
10104K@30Hz 7.1CH
1 0 0 1 4K@30Hz HDR 7.1CH
01101080p@60Hz 2CH
01011080p@60Hz 5.1CH
00111080p@60Hz 7.1CH
4

Dip Switch Status
Resolution Information
1234
11101080i@60Hz 2CH
11011080i@60Hz 2CH
10111080i@60Hz 7.1CH
0111 1080p@60Hz HDR 7.1CH
1111
1. Read only the EDID
that was first connected
to the output
2. Connect 4 outputs
at the same time, only
read the EDID of HDMI
1 output
5
Remote Control / Front Panel Buttons
• The remote control replicates the buttons on the front panel and both can be used
to direct each of the 4 inputs to any of the four output displays.
• If the remote loses effective range the battery may require replacement.
• Pull out the battery holder and replace the battery noting the correct polarity.
• The remote uses 3V CR2025 coin type battery.
MAINTENANCE
• Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Waste batteries
can be returned to any waste battery recycling point which are provided by most battery retailers.
Contact your local authority for details of recycling schemes in your area.
Made in China
PO Box 13362 Dublin 2
PR2 9PP
Man Rev 1.0
6
SPECIFICATIONS
HDMI version HDMI2.0 (HDR, YUV4:4:4)
Compatible with HDCP2.2,HDCP1.4
HDMI interface 4 HDMI input, 4 HDMI output
Transmission rate 18Gbps
Bandwidth 600MHz
Resolution 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz,
3840×2160@24/25/30/60Hz, 4096×2160@24/25/30/60Hz
Audio format LPCM7.1/DTS-HD/DTS-Audio/Dolby Digital plus
Dolby TrueHD 7.1/Dolby Digital 7.1CH/Dolby Atmos
RS-232 3 Pin (GND/Rx/Tx) Baud rate 9600
EDID setting EDID DIP switch (16 positions)
IR Remote frequency 20KHz~60KHz
Voltage 5V DC 1A
Power consumption <4W
Working temperature -20oC~60oC
Storage temperature -30oC~70oC
Humidity 0~90%RH (No Condensation)
Weight 375g
Dimensions (WxDxH) 210.0 x 80.0 x 21.0mm
Protection ESD protection
1a Contact discharge level 2 (±4KV)
1b Air discharge level 3 (±8KV)
Implementation of the 󰀬andard: IEC61000-4-2
Lightning protection, Surge protection