PROAIM CINEMA P-SWCC-10 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Sky-Walker Pro Cinema Cable cam System (P-SWCC-10)
Assembly Manua l
Chain Pulley
Balance Assembly
Charger Accessories Power Cable
Remote
Climbing Hooks
Chain Puller
Cablecam

2
1
Stand With 100mtr Dyneema Rope 100mtr Steel Safety Cable
Flight Transport Case
Input Voltage 24V
Power 2.2KW
Nominal Current 91A (Max)
Controller voltage 12V
Nominal Current 85mA
Tx/Rx Power 100mw
Load Capacity 10Kg/22lb
Maximum Speed 40km/h
Control Distance 100mtr
Target Distance Yes
Auto LoopYes
Product size (L x W x H) 113cm x 20cm x 23.5cm
Specificaons
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.

3
• Loosen bolts and slide out the ends of the
leg ll fully opened. Then ghten the bolts
again.
• Repeat the same steps for the other side of
the legs to assemble the Stand. Next, insert
threaded Rod Axle in Wire Spool Wheel.
• Open Wing Nut from Threaded Rod and
aach it with one side each of both the legs
of Stand.
Sky-Walker Setup
• Then place it onto Rope Stand and ghten
wing nuts on both sides for proper rope
movement.
Assembling the Chain Puller
• Now you can pull the rope conveniently for
use.
• Press the lever to unlock the Ratchet lock.
Then pull out the metal rope along with the
pulley.

4
• Aach one end of the cable to an anchor.
Then pull the chain puller to drag the rope.
• Aach this pulley with Climbing Hook on
the same anchor but slightly above Chain
Pulley. Insert the rope into Cable Cam in the
sequence of 1, 2, and 3.
• Insert the rope into Pulley and aach
Climbing Hook.
• Make a knot with the rest of the rope. Fix
Climbing Hook with it.
• Now aach this Climbing Hook at a suitable
locaon.
• Insert the rope into Cable Cam in a se-
quence of 1, 2, and 3. Secon-1
Secon-2Secon-3

5
NOTE: The Main Drive Wheel and two Outer Wheels can be adjusted depending on the rope tension.
Adjustment of the hooks will cause the rope to be pushed harder or less hard against the Main Drive
Wheel. Since the Main Wheel relies on tension against the cable, it is
important to adjust the hooks properly.
NOTE: Fix Climbing Hook with Safety Cable
and aach it to either of the anchors
• Insert Safety Cable into Cable Cam starng
from the top of Secon 3, taking it under
Secon 2, and crossing it from the top of
Secon 1. Then x it onto the anchor on
another side of the shoong.
• Then ax your Baery (Not included) and
connect it with Cable Cam.
Assembling for Double Safety of Cable Cam
NOTE: To sync the remote with sky walker,
you need to switch ON this buon for the
binding process.
Secon-1Secon-2
Secon-3
Safety clamp Safety cable
• There is an adjustment in the mounng of
the Main Drive Wheel. You can shi its
posion depending on the rope tension.

6
NOTE: Kindly check the gap between rope & wheels for proper funconing of Cable cam. In case, there is
a gap between the rope & wheel, please minimize it by adjusng the motor clamp.
To do the same, unscrew the Motor Clamp bolts with an Allen key on both sides as shown in the
image.
Now, slide it upwards to maximum vercal posion. Screw the bolts again on both sides by using the
Allen key. The gap will be minimized & now, the rope will have a beer grip on wheels.
Wireless Remote Controller & Antenna
Precauons!
Read the safety messages listed below before operaon!
• Do not use the product at night or during bad weather condions, like rain or thunderstorms. It can
cause errac operaon or loss of control.
• Do not use the product when visibility is limited.
• Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may cause
errac operaon or loss of control.
• Interference may cause a loss of control. Therefore, to ensure the safety of you and others, do not use
it in the following place.
 Near any site where other radio control acvity may occur.
 Near people or roads.
 On any pond/ lake when passenger boats are present.
 Near power lines or communicaon broadcasng antennas.
• Do not use this product when you are red, uncomfortable, or under the of Alcohol or drugs. Doing so
may cause serious injury to yourself or others.
• The 2.4GHz radio band is limited to line of sight. Always keep your model in sight. Always keep your
model in sight as a large can block the RF signal and lead to loss of control.
• Never grip the transmier antenna during operaon. It signicantly degrades Signal quality and
strength and may cause loss of control.

7
• Do not touch any part of the model that may generate heat during operaon, or immediately aer use.
The engine, motor or speed control, may be very hot and can cause serious burns.
• Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equip-
ment, read this manual and follow the instrucons carefully.
• Make sure the product is properly installed in your model. Failure to do so may result in serious injury.
• Make sure that the receiver's baery is disconnected before turning o the to do so may lead to unin-
tended operaon and cause an accident.
• Ensure that all motors operate in the correct direcon. If not, adjust the direcon rst.
• Make sure that the model stays within range in order to prevent loss of control.
• The antenna(s) used for this transmier must be installed to provide a separaon distance of at least 20 cm from all
persons and must not be co-located or operang in conjuncon with any other transmier. End-users and installers
must be provided with antenna installaon instrucons and transmier operang condions for sasfying RF exposure
compliance.
The radio control system controls movements of Cable Cam. The highly sophiscated radio transmission
system works on 2.4 GHz powerful radio frequency band and transmits very clear signal to the receiver
Antenna. The 2.4 GHz RF signal propagates in straight lines and can also get around objects on its path.
The remote control system guarantees a long range, jamming-free transmission and long baery-life ex-
perience.
Turn it On - Turn ON the Power switch. The posion of all throle switches A, B, C, D; must be at #1
(while turning on the remote every me). The LCD screen of remote will display Tx On & Rx On when
connected, and an error will be displayed if Rx is out of range.
Le Sck – It is used to give Direcon & Speed to cable cam. Move the sck le/right to give direcon
and move it up/down for speed. When you start operang Cable cam - gradually accelerate the speed, to
avoid damage to the cable.
Right Sck – It is used to Set Target Distance & Automac Loop Modes.
Target Distance (Manual mode) – Set Start and Stop points anywhere on cable by point A (move sck
downwards) & point B (move sck upwards). Aer entering the target distance, the remote locks on it
and follows it perfectly. Give Direcon & Speed with Le Sck, and operate it manually. Once you leave
the sck at neutral posion, it will stop right there.

8
YOUR PROAIM SKY-WALKER PRO CINEMA CABLE CAM SYSTEM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.
Automac Loop Mode – Select target distance by point A & B. Shi the throle switch labelled SwC at
posion #3. Set the Speed with Le Sck and forget it! It will move and capture shots automacally for
you.
Workable Zone
The Normal Operang Zone of approx. 84mtr is recommended, which is marked with points A & B. The
Cable Cam running at high speed takes around 5mtr of length for momentum to stop itself, which comes
under Safety Zone. It is not recommended for your Cable Cam running at high speed to move within 3mtr
of Danger Zone. While selecng target distance lock points; it is suggested to consider speed & precau-
ous zones.