Probrite FSN15-4K-WH Setup guide

Before returning to the store, call or email PROBRITE
Customer Service 9am-5pm EST Monday to Friday.
1-844-507-5651
[email protected]om
PROBRITE.COM
Questions? / Missing Parts? / Need Accessories?
Visit us online anytime or call us to get information on our product range, download
detailed spec & photometric files, find product and mounting accessories, view
installation tutorials and videos, and learn about our DLC® rebate eligible products.
INSTALLATION,
USAGE, & CARE GUIDE
FUSION LED
WALLPACK/
FLOOD LIGHT KIT
Model No.
Mfr. SKU
FSN15-4K-WH
FSN28-4K-WH
103-08200002-1
103-08300002-1

3PROBRITE.COM
Please call 1-844-507-5651 or email [e-mail] for further assistance.
2
Visit www.probrite.com/install for installation video tutorials and product support
Table of Contents......................... 2
Safety Information........................2
Pre-Installation..............................3
Planning Installation......................3
Specifications.................................. 3
Tools Required................................ 3
Hardware Included........................ 4
Package Contents......................... 4
Installation..................................... 5
Operation......................................10
Care & Cleaning............................10
Troubleshooting...........................10
Warranty.........................................11
Table of Contents
Safety Information
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
NATIONAL ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
PRECAUTIONS
☐Please read and understand this entire
manual before attempting to assemble,
install, or operate this light fixture.
☐This light fixture requires a 120-277Volt
AC power source.
☐Some codes require installation by a
qualified electrician.
☐This light fixture must be properly
grounded.
☐Make sure connections are secure using
wire nuts, crimp-on lugs or other ap-
proved connecting devices
☐This light fixture should be installed out-
doors to a wall or to the ground.
☐This product may contain chemicals
known to be hazardous. Thoroughly
wash hands after installing, handling,
cleaning or otherwise touching the
product.
WARNING: Turn the power o at the circuit
breaker or fuse. Place tape over the circuit
breaker switch and verify power is o at the
light fixture.
WARNING: Risk of fire. Keep the lamp heads at
least 3 in. (76mm) from combustible materials.
CAUTION: Burn hazard. Allow the light fixture
to cool before touching.
NOTICE: Do not connect this fixture to a
dimmer switch.
Pre-Installation
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the
Hardware Included and Package Contents sections. If any part is missing or damaged, do
not attempt to assemble, install, or operate this light fixture.
Estimated installation time: 20 minutes
MODEL FUSION 15W FUSION 28W
Lumens (Light Output) 1500 Lumens 3000 Lumens
Watts (Power Consumption) 15 Watts LED 28 Watts LED
Replaces 70 Watt Metal Halide 100 Watt Metal Halide
Lumens/Watts (Efficacy) 100 lumens per watt 107 lumens per watt
Power Requirements (Input Voltage) 120-277VAC
Light Color (CCT) 4000 Kelvins (Bright White)
Dimmable Non-Dimming (Do not wire to dimming switch)
Operating Modes Switch-Controlled:
Flip switch to turn light fixture ON and OFF.
Use external photocell light sensor, timer or
motion sensor for automatic functionality
(sold separately)
SPECIFICATIONS
TOOLS REQUIRED
Phillips
Screwdriver
Wire strippers/
cutters
Circuit tester
Safety
goggles
Work
gloves
Silicone
Sealant
Ladder
NOTICE: FCC Regulations state that any
unauthorized changes or modifications to
this equipment not expressly approved by the
manufacturer could void the user’s authoriza-
tion to operate this equipment.
Save these instructions

5PROBRITE.COM
Please call 1-844-507-5651 or email [e-mail] for further assistance.
4
Visit www.probrite.com/install for installation video tutorials and product support
Pre-Installation (continued)
HARDWARE KIT
NOTE: Hardware not shown to actual size.
AA BB CC
Part Description Quantity
AA #8-32 x 3/4" philips mounting bracket screw 2
BB Wire nut 3
CC Allen key 1
PACKAGE CONTENTS
Part Description Quantity
ALight fixture 1
B1/2" NPS threaded knuckle mount handle 1
CWall/Eave mounting base plate 1
DUniversal junction box mounting plate 1
EMounting plate hex bolt 2
FHands-Free Hooking Wire 1
GTightening washer for knuckle mount 1
2Shut electric power off
☐At wall switch verify it is in the o
position (fig 1).
☐At the main electrical panel turn o
the circuit breaker that supplies power
to the outlet box you are working on
(fig 2).
☐For screw-in type fuses unscrew the
fuse that supplies power to the outlet
box you are working on (fig 3).
(fig 1). (fig 2).
(fig 3).
NOTE: The junction box cover plate is not provided in the box. It is available separately
with your retailer.
A
BG
C
E
D
F
Installation
1For best results
Wall Mount (A or B Mount)
Eave Mount (A or B Mount)
Swivel Knuckle Flood Mount (B Mount)
☐Install light 6-15 feet above the ground
for wall applications or on ground for
flood application.
☐The fixture can be mounted in multiple
ways:
A. Wall/Eave Mount: Using the
wall mounting base (C) and the
mounting plate (D) over a junction
box.
B. Swivel Knuckle Flood Mount: Can
be used with a domed cover plate
(not provided) on a junction box.
☐When installing two fixtures on one
switch, make sure the switch is rated for
at least a 1A inductive load.
☐Do NOT wire to a dimming switch.
Mount with 1/2" NPS
Threaded Flood
Mount (Junction box
dome cover plate
with center hole not
included)
Mount with
Universal
Junction
Box Wall/
Eave Base
(included)
Junction box
domed cover
plate with
center hole
Landscape
Post
IMPORTANT INFORMATION: Domed cover
plates for junction boxes, landscape posts,
and other mounting arms and accessories
are available. Please contact your retailer or
PROBRITE's customer support.

7PROBRITE.COM
Please call 1-844-507-5651 or email [e-mail] for further assistance.
6
Visit www.probrite.com/install for installation video tutorials and product support
Installation (continued)
3A
3B
Installing Wall/Eave Mount Base
(Optional if desired)
Installing with Swivel Knuckle Mount
For mounting to domed junction box cover plate (sold
separately) or landscape post (sold separately)
C
NOTE: The fixture comes with the knuckle
handle (Fig. 1) and the wall mount base plate
(C) is available separately within the box.
NOTE: The fixture comes with the 1/2" threaded
NPS swivel knuckle mount (B) and is compatible
with standard domed junction box cover plates
with a center hole or landscape posts
Installation (continued)
(fig 1).
(fig 3).
(fig 2).
(fig 4).
Wall/Eave Mount Base Set Up on Standard Junction Boxes
For Ground and Wall/Eave Mounting
☐Using allen key, remove the screw from
the center of the knuckle handle as
shown in fig. 2.
☐Use the wall mount base plate (C),
provided separately in the box, and
thread wires through the hole of the
plate, being careful not to pinch the
wires.
☐Place the fixture head in required
orientation with the plate and tighten
the screw on the knuckle which was
removed earlier. (fig. 3).
☐Place wires through the hole in the domed
junction box cover plate or landscape post.
☐Place tightening washer on back side of
domed cover plate.
☐Screw 1/2" NPS threaded knuckle mount (B)
into the center hole of the domed plate or
landscape post and, if hole isn't threaded,
use tightening washer (G) to tighten fixture
into place.
☐Use provided allen key (CC) to loosen
bolt in center of knuckle mount and select
desired angle. Tighten bolt to secure into
place.
Remove the
screw here
E
D
CC
4A Removing the Mounting Plate from Wall Base
and Fixing it on the Wall/Eave
(Only Applicable for Wall/Eave Mount if using the base plate)
☐Remove the mounting plate (D) from
the back of the fixture by loosening the
screws using the allen key (CC)(Fig. 1)
☐Align the holes of the mounting plate
with the "TOP" marking oriented
upwards (or closest to wall if eave
mounted) with the junction box on the
wall and fix the mounting plate (D) on
the junction box by using the two #8
screws (AA). (Fig. 2)
Wall / Eave Mount using the base plate
Wall Mount
NOTE: Use any other suitable bolts or fasteners
as applicable to your mounting surface.
AA
D
(fig 1).
(fig 2).
TIP: Only unscrew the tightening bolt (E) far
enough to remove the mounting plate (D).
Do not fully remove the tightening bolt (E).
D
F
5AHooking Hands-Free Install Wire
(For install with Wall/Eave Mount Base Plate Only)
☐Take the round "ball" head of the
hands-free wire (F), attached to back
of base plate, and place it behind the
bottom-center "notch" of the mounting
plate (D)
☐Ensure the fixture can now hang-free
to allow for hands-free connection of
the electrical wires
Wall/Eave Mount
NOTE: After electrical connections are made
un-hook the hands-free wire (F) and then
mount the fixture onto the mounting plate (D).
TOP
D
F
TOP
B
G
B
(Domed
junction box
cover plate)
(Landscape
post)

9PROBRITE.COM
Please call 1-844-507-5651 or email [e-mail] for further assistance.
8
Visit www.probrite.com/install for installation video tutorials and product support
E
D
CC
Installation (continued)
☐Loosen the screw on swivel portion of
the knuckle (B), adjust the fixture to a
suitable orientation, and then tighten
the screw.
☐Restore power to the breaker and light
switch and test if light turns on.
B
Swivel Knuckle Flood Mount
☐Caulk around the mounting plate (D)
and surface with silicone sealant (not
included).
☐If applicable, plug all unused holes and
seal threads with silicone.
D
Plug unused
holes, if any
D
BB
Installation (continued)
5A/B 7A
8A/B
Making the electrical
connections
Caulking around the
light fixture
Adjusting the light
head and testing
(fig 1).
LIGHTING
FIXTURE
(+) LINE
(-) COMMON
GROUND
BLACK
WHITE
GREEN
Wall/Eave Mount
6ASecuring the fixture and wiring
☐Once the fixture is wired, place the
fixture on the mounting plate and use
the two screws(E) to tighten the fixture
on the plate (D) by using the allen key
(CC).
☐If necessary, strip 3/8" of insulation
from junction box or fixture (A) wires
(fig 1).
Wall Mount
Wiring Instructions
BB
☐Connect fixture black wire to house
black wire, the (+) line, and fixture
white wire to house white wire, the (-)
common by twisting the exposed wires
together and using the wire nuts (BB).
Ensure no loose wires.
☐Connect house ground wire to the
green fixture ground wire, by twisting
the exposed wires together and using
the wire nuts (BB).
Swivel Knuckle Flood Mount
TIP: Hold stripped ends near each other and
align any frayed strands (do not twist wires).
Push the wires into wire nut (BB) and use your
fingers to twist the wire nut clockwise until tight.
Check for tightness by pulling wires.
B
Use the hex screw
here to adjust the
orientation using
provided allen key
(CC)
Seal around
hole
Use the hex screw
here to adjust the
orientation using
provided allen key
(CC)

11 PROBRITE.COM
Please call 1-844-507-5651 or email [e-mail] for further assistance.
10
Visit www.probrite.com/install for installation video tutorials and product support
Care and Cleaning
☐Shut o main power supply before cleaning the product. To prolong the original
appearance, clean the light fixture with clear water and a soft, damp cloth only.
☐Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints,
solvents, or any other chemicals on this light fixture. They could cause a premature
deterioration of the finish and may void the warranty.
☐Do not spray the light fixture with a hose or power washer.
Troubleshooting
If Light does not come on:
☐Verify that the power is turned ON from the circuit breaker and wall switch.
☐Verify the wiring for the fixture is done properly.
☐Verify the line voltage is correct.
If Light flickers:
☐Do not wire to a dimming switch, use a standard ON/OFF switch
5-Year Limited Warranty
This is a limited warranty oered by Probrite for a period of five years from the date of purchase
to its customers. Probrite warrants to customers that the products will be free from defects
in material and workmanship. The obligation of Probrite under this warranty is limited to the
provision of replacement of products and is extended to the original purchaser of the product
on presenting valid purchase receipt or other proof of date of original purchase acceptable to
Probrite. The receipt is required for rendering the warranty performance. Any warranty claims
without original proof of purchase would not be accepted.
It should be noted that the warranty does not apply to Probrite products that have been
altered or repaired by unauthorized personnel, have been subjected to neglect, abuse, misuse
or accident or damages caused during shipping. Any other products not manufactured by
Probrite which have been supplied, installed and/or used in conjunction with Probrite products
are not covered under this warranty. Any damages caused by replacements bulbs, LEDs or
corrosion or discoloration of brass components are also not covered by this warranty.
Limitation of Liability:
In no event Probrite shall be liable for indirect, consequential, incidental or special damages, or
lost profits. Probrite is not liable for any claims or damage arising out of or connected with the
manufacture, sale, delivery, use, maintenance and repair or modification of Probrite products,
or supply of any replacement parts that, exceed the purchase price of Probrite products giving
rise to a claim. Labor charges to remove or install the fixtures will not be accepted.
To Claim:
Please contact PROBRITE customer service at 1-844-507-5651 or email support@PROBRITE.
com and include your name, address and contact number, along with a copy of the purchase
receipt and a brief description of the problem.
Operation
☐Once the fixture is installed, turn power
back on from the circuit breaker and
switch.
☐Flip switch ON and OFF to ensure light
functions properly.
Switch-controlled operation enables the light fixture to turn ON and OFF by
flipping a standard light switch. To add automatic Dusk to Dawn control or
motion sensing external sensors like a photo-control, motion-sensor or timer is
required (sold separately).
SWITCH-CONTROLLED
NOTE: This fixture is not dimmable, so it
is best to not wire to a dimming switch.
SWITCH
CONTROLLED

Before returning to the store, call or email PROBRITE
Customer Service 9am-5pm EST Monday to Friday.
1-844-507-5651
[email protected]om
PROBRITE.COM
Questions? / Missing Parts? / Need Accessories?
RETAIN THIS MANUAL FOR FUTURE USE
Para las translaciones en español,
visit www.probrite.com/install