PROCET PT-PSE105GBS-D-10 User manual

２ Dimensions
󾋸󾋷󾋼󾋸󾋷
ＷＷＷ．ＰＲＯＣＥＴＰＯＥ．ＣＯＭ
Ｕｓｅｒ Ｍａｎｕａｌ
Ｏｖｅｒｖｉｅｗ
Ａｐｐｅａｒａｎｃｅ
Ｄｅｃｌａｒａｔｉｏｎ
1．ＤＣ Ｐｏｗｅｒ Ｉｎｄｉｃａｔｏｒ
2．ＰｏＥ Ｏｕｐｕｔ Ｐｏｒｔ
3．ＳＦＰ Ｉｎｐｕｔ Ｐｏｒｔ
4.Ｄａｔａ Ｉｎｄｉｃａｔｏｒ
5.ＰｏＥ Ｌｏａｄ Ｉｎｄｉｃａｔｏｒ
6.ＤＣ Ｉｎｐｕｔ ｐｏｒｔ
7.ＤＩＮ Ｒａｉｌ Ｍｏｕｎｔｉｎｇ
Ｂｒａｃｋｅｔ
8.ＧＮＤ Ｔｅｒｍｉｎａｌ
󾋽
󾋾
󾋿
󾋸
󾋹
󾋺
󾋻
󾋼
󾋸󾋻󾋻󾋼
󾌀󾋼󾋷 󾋺󾋼󾋻
1Ｐｒｏｄｕｃｔ Ｄｉａｇｒａｍ
Copyright ©2023 Creative Lianjie Network
Technology Co.Ltd All rights reserved.
This document belongs to PROCET company. It is not
allowed to reproduce and modify without the original
author's permission. It is PROCET's policy to improve its
products as new technology components, software , and
firmware at any time. PROCET, therefore, reserves the right
to change specifications without prior notice.
Please follow WEEE (Waste Electrical and Electronic
Equipment) disposal instructions for old electronic
products.Please do not dispose of the old product in your
general household waste bin.
The symbol indicates that the product should not be
discarded as unsorted waste but must be sent to separate
collection facilities for recovery and recycling.
PT-PSE105GBS-D-10 is a single-port media converter with PoE function. The single PoE output
port delivers 1.75A up to 95W(max) power for remote PDs over 4 pairs. Equipped detecting chip
inside which will make the PoE identification handshake with IEEE802.3af/at/bt PDs. Such as PTZ
cameras, wireless APs, base stations, and other PoE-powered devices which need high power
watts. Protecting non-PoE powered devices.
RJ45 port supports 100/1000Mbps, 2.5G/5G/10GbE NBase-T, while the fiber slot only supports
10GE SFP+ of optical module. Enclosed in an IP40 high-impact metal case with a DIN Rail mount
bracket, designed for indoor use but can work outdoors by covering it with a waterproof case. It
works with an input voltage of 50-57Vdc and operates under -40°C to +65°C. For planning
purposes, the effective distance is 100 meters over Cat6 cables.

Ｓｐｅｃｉｆｉｃａｔｉｏｎ
Ｔｒｏｕｂｌｅｓｈｏｏｔｉｎｇ
       
www.procetpoe.com
Ｉｎｐｕｔ
ＰｏＥ Ｓｔａｎｄａｒｄ
Ｃｌａｓｓ Ｌｅｖｅｌ
ＰｏＥ Ｐｏｗｅｒ Ｐｉｎｓ
Ｗｏｒｋ Ｔｅｍｐ．
５０－５７Ｖｄｃ ２．０Ａ
ＩＥＥＥ８０２．３ ａｆ／ａｔ／ｂｔ
Ｃｌａｓｓ ８
Ｎｅｔｗｏｒｋ Ｐｒｏｔｏｃｏｌ ＲＪ４５：１００Ｍ／１０００Ｍ／２．５Ｇ／５Ｇ／１０Ｇ,ＳＦＰ：１０Ｇ
Ｄａｔａ Ｓｐｅｅｄ
ＩＥＥＥ８０２．３ｕ／ａｂ／ｂｚ／ａｎ ＩＥＥＥ８０２．３ａｅ
Ｏｕｔｐｕｔ
ＰＴ－ＰＳＥ１０５ＧＢＳ－Ｄ－10
ＥＭＣ
Ｄｉｍｅｎｓｉｏｎｓ & NW １４４．５ｍｍ Ｘ ９５ｍｍ Ｘ ３５．４ｍｍ ４８５ｇ
Ｆａｉｌｕｒｅ
Ｐｈｅｎｏｍｅｎａ Ｃａｕｓｅ Ａｎａｌｙｓｉｓ Ｓｏｌｕｔｉｏｎｓ
Ｐｏｗｅｒ ＬＥＤ
Ｌｉｇｈｔ ｏｆｆ
Ｎｏｔ ｐｌｕｇｇｅｄ ｉｎ ／ ｎｏ ｐｏｗｅｒ Ｐｌｕｇ ｉｎ ｔｈｅ ｐｏｗｅｒ ｃｏｒｄ
Ｌｏａｄ
Ｉｎｄｉｃａｔｏｒ
Ｌｉｇｈｔ Ｏｆｆ
ＥＮ ５５０３２：２０１５／Ａ11：２０２０ ＥＮ ５５０３５：２０１７／Ａ11：２０２０
Model
4/5(+),7/8(-)& 3/6(+),1/2(-)
Poor Power outlet
Poor Power cord
Power cable is not plugged in
－４０°C ｔｏ ６５
４８－５５Ｖｄｃ １７５０ｍＡ
°C
firmly
Check if the socket connection
is loose, if the AC cable is
damaged, or if the power
supply is abnormal.
Device issues Device replacement
Poor network cable contact or
network cable failure.
Non-PoE compliant PD or
unsupported PD or
Re-plug the network cable
or replace the network
cable.
mismatched PD PD replacement
PD Damage PD replacement
Check if the total length of the
network connection cable exceeds
100 meters.
Shorten the connection
distance, or add an extender/
repeater.
SFP port signal source malfunction Check if the switch working
properly.
Ethernet data transmission failure
Ｄａｔａ
Ｔｒａｎｓｍｉｓｓｉｏｎ
Check if the cable comply with
the EIA/TIA568B or 568A.
Change good network cable if
the previous cable is poor.
Ａｂｎｏｒｍａｌｉｔｙ
Caution
1. Please read the instructions carefully and follow the
standard operating procedures before using.
2. Please place it in a well-ventilated and dry area, and it is
for indoor use only.
3. Connect the DC power cable with positive and negative
wires into the DC terminal block of Procet Injector.
4. Connect a fiber cable with SFP+ optical module at 10G
from your switch into the injector's SFP slot for data Input.
(The optical module does not include in the package). You
can choose either single-mode or multi-mode SFP
transceivers.
5. Connect a CAT6 cable with the RJ45 connector into the
RJ45 socket labeled PoE. On the other end of the CAT6
cable, connect to your PoE Device (such as IP Cameras etc)
. The total Ethernet cable length can not exceed 100
meters.
6. The device must be placed on a stable surface,
preferably affixed and mounted permanently. Do not
leave it "dangling" and use plugged-in cables in tension
as support. Drops, falls, and impacts experienced by the
injector can compromise the internal components & cause
premature failure.
7. Do not place heavy objects on top of this injector. Allow
at least 5cm of clearance on all sides of the device for
heat ventilation / natural convection.