Procom PC32VFC User manual

Thisfireboxhas been tested and approved under ANSI Z21.91 for use withanyANSI
Z21.11.2approved gas logs.
Do notstoreor use gasolineor other flammablevaporsand liquidsin vicinityof
thisor anyother appliance.
WHAT TO DO IFYOU SMELL GAS
·Do nottryto lightanyappliance.
·Do nottouch anyelectrical switch; do not use anyphonein your building.
·Immediatelycall your gassupplier from aneighbor’sphone. Followthegas
supplier’sinstructions.
·If you cannotreachyour gas supplier, call thefire department.
Installation andservice must beperformed byaqualifiedinstaller, service agency
or thegassupplier.
Carefullyreview theinstructions supplied withthedecorative typeunvented room
heater for theminimum fireplace sizerequirement.
DO NOT INSTALLAN APPLIANCE IN THIS FIREBOX UNLESS THIS FIREBOX MEETS
THE MINIMUM DIMENSIONS REQUIRED FOR THE INSTALLATION.
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY, OR LOSS OF LIFE.
PC32VFC-651 and PC36VFC-701
CAUTION FOR YOUR SAFETY
FOR USE ONLY WITH A LISTED GAS-FIRED UNVENTED DECORATIVE ROOM
HEATERNOT TO EXCEED 40,000BTU/HR. DO NOT BUILD A WOODFIRE.
VENT-FREE GAS FIREPLACE
Model # PC32VFC & PC36VFC
Questions about installation, operation, or troubleshooting? Before returning to your retailer, contact our
customer service department at 1-877-886-5989, 8:00 a.m.- 4:30p.m., EST, Monday-Friday or e-mail
[e-mail]
.

2
TABLE OF CONTENTS
Important Safety Information...........................................................................................................................................3
Product Feature...............................................................................................................................................................4
Local Codes....................................................................................................................................................................4
Locating Firebox..............................................................................................................................................................5
Air For Combustion and Ventilation.................................................................................................................................6
Installation.......................................................................................................................................................................9
Replacement Parts........................................................................................................................................................13
WARNING:READ THE INSTALLATION & OPERATION INSTRUCTIONS BEFORE USING THIS APPLIANCE
IMPORTANT: Read instructions andwarnings carefully before starting installation. Failure to follow these instructions
may result in a possible fire hazard and will void the warranty.
PRODUCT SPECIFICATIONS
32 and 36”Models
Model A B C D E F G H I
PC32VFC 2.381" 18.515" 19° 24.060" 7.567" 21.382" 20.718" 31.732" 29.323"
PC36VFC 2.397" 18.870" 25° 28.770" 6.622" 26.740" 25.949" 36.031" 33.630"
Figure 1

3
IMPORTANT SAFETY INFORMATION
IMPORTANT: Read this owner s manual carefully and completely beforetrying to assemble, operate, or service this
fireplace. Improper use of this fireplace can cause serious injury or death from burns, fire, explosion,electrical shock,
and carbon monoxide poisoning.
Only a qualified installer, service agent, or local gas supplier may install and service this product.
WARNING: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other
appliance.
CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the flu with headaches,
dizziness, ornausea. If you havethese signs, thefireplace may not be working properly. Get fresh air immediately!
Havefireplace serviced.Some people are more affected by carbon monoxide thanothers. These include pregnant
women, people with heart or lung disease, people who are anemic, those under the influence of alcohol, and those
living in highaltitudes.
WARNING: Any change to this fireplace or its controls can be dangerous.
WARNING: Do not allow fans to blow directly into fireplace. Avoid any drafts that alter burner flame patterns.
WARNING: Do not use ablower insert, heat exchange insert or other accessory not approved foruse with this
firebox.
Due to high temperatures, the appliance should belocated out of traffic andaway from furniture and draperies. Do not
place clothing or otherflammable material onor near theappliance.Never placeany objects in the fireplace.
Fireplace becomes very hot when running fireplace. Keep children and adults away from hot surfaces to avoidburns
or clothing ignition. Fireplace will remain hot for atime after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they arein the room with the firebox.
You must operate this fireplace withthe fireplacescreen, hood if provided, in place. Make surethese partsare in
place andscreens are closed beforerunning firebox.The supplied hoodmay not bereplaced withahoodwhich may
be provided with a log fireplace.
INSTALLER: DO NOT DISCARD THIS MANUAL LEAVE FOR HOMEOWNER’S
FUTURE REFERENCE
.

4
1. Do not placePropane/LPsupply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors.
2. Do not use this fireboxas a wood-burning fireplace. Use only decorativeunvented room heaters (log set).
3. Keep all air openings in front and bottom of fireplace clear andfree of debris. This will ensure enough air for proper
combustion.
4. Do not run fireplace:
lWhere flammable liquids or vapors are used or stored.
lUnder dusty conditions.
5. Before usingfurniture polish, wax, carpet cleaner, or similar products, turn fireplace off.If heated, the vapors from
these products may create a white powder residue within burner boxor onadjacent walls or furniture.
6. Do not use fireboxif it has been under water due to shock hazard that could result with the blower accessory (if
installed) in place.
7. Turn fireboxoff and let cool before servicing. Only a qualified service person should service and repair firebox.
8. Operating fireboxaboveelevations of4,500 feet could cause pilot outage.
9. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lb. capacity.
10. This fireboxshould not be installed ina bedroom or bathroom.
11. Do not add extra logs orornaments such as pinecones, vermiculite, or rock wool. Using these added items can
cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of fireplace. After
servicing, always replace screen before operating fireplace.
12. Use only provided hood.
QUALIFIED INSTALLING AGENCY
Only aqualified agencyshould perform installation and replacement of gas piping, gas utilization equipment or
accessories, and repairand servicing of equipment. Theterm “qualified agency”means anyindividual,firm,
corporation, or company that either inperson or through a representative isengaged in and is responsible for:
a) Installing, testing, or replacing gas piping or
b) Connecting, installing, testing, repairing, or servicing equipment; that is experienced in such work; that is familiar
with all precautions required; and that has complied with all the requirement of the authority having jurisdiction.
PRODUCT FEATURES
OPERATION
This fireboxis designed for use with approved ANSI Z21.11.2 decorative type unventedroom fireplaces. (Physical
size limitations apply. Refer to minimum fireboxrequirementssupplied with log fireplace.) It requires no outside
venting or chimney making installation easy and inexpensive. When used without the blower, the fireboxrequires no
electricity making it idealfor emergency backup heat.
LOCAL CODES
Install and use fireplace with care. Follow all codes. In the absence of local codes, use the latest edition of The
National Fuel Gas Code, ANSI Z223.1, also known as NFPA 54*.
*Available from:
American National Standards Institute, lnc. National Fire Protection Association, lnc.
1430 Broadway 1 Batterymarch Park
New York, NY 10018 Quincy, MA 02269-9101

5
This fireplace is designed for vent-free operation. State and local codes in some areas prohibit the use of vent-free
fireplaces.
State of Massachusetts: The installation must be made by alicensed plumber or gas fitter in the
Commonwealth of Massachusetts. Sellers of unvented propane or naturalgas-fired supplemental room
fireplaces shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.
In the State of Massachusetts, unvented propane or natural gas-fired space fireplaces shall be prohibited in
bedrooms and bathrooms.
In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts
requires that a flexible appliance connector cannot exceed three feet in length.
LOCATING FIREBOX
PLANNING
Plan where you will install the firebox.This will save time and money later when you install the firebox. Before
installation, consider thefollowing:
1. Where the fireboxwillbe located. Allow for wall and ceiling clearances (see Installation Clearances, page 9).
2. Everything needed to complete installation.
3. These models CANNOT be installed in a bedroom unless the maximum BTU rating of the installed vent-free log set
is less than 10,000 Btu/Hr.
4. Proper air for combustion and ventilation (page 6).
UNPACKING
1.Rip of f thewrapping film around unit.
2.Remove the top packaging and 4 angle beads.
3.Remove protective plastic wrap
4.Check for any shippingdamage. If fireboxis damaged,promptly inform your dealer where you bought the firebox.
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM FIREPLACES
Water vaporis aby-product of gas combustion. An unventedroom fireplace produces approximately one (1) ounce
(30 mL) of water for every1,000 BTUs (.3 kw) of gas input perhour. An unventedroomfireplace is recommended as
asupplemental fireplace(a room)rather than aprimary heat source (anentire house). In mostsupplemental heat
applications,the water vapor does not create aproblem. In most applications, the water vaporenhances the low
humidity atmosphere experiencedduring coldweather. Thefollowingsteps will helpinsure thatwater vapordoes not
become a problem:
1. Be sure the fireplace is the proper size for the application, including adequate combustion air and circulation air.
2. If there is high humidity, the dehumidifier may be used to helplower the water vapor content of theair.
3. Do not use an unvented room fireplace as the primary heat source.

6
AIR FOR COMBUSTION AND VENTILATION
WARNING: This fireplace should notbe installed in a confinedspace or unusually tight construction unless
provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure
proper fresh air for this and other fuel-burning appliances in your home.
PRODUCING ADEQUATE VENTILATION
This fireplace shall not be installed ina room or space unless the required volume of indoor combustion air is
provided by the method described in the NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, the
INTERNATIONAL FUEL GAS CODE, or applicable local codes.
The following are excerpts from National Fuel Gas Code, NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and
Ventilation. All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 6 through 8 will help you classify your space and provide adequate ventilation.
Confined and Unconfined Space
The National Fuel Gas Code,ANSI Z223.1 definesaconfined space as aspace whose volume is less than 50 cu. ft. per
1,000 BTU/hr(4.8 m^3per kw) of the aggregate input rating ofall appliances installed inthat spaceand anunconfining
space as aspace whose volume is not less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3per kw) of the aggregate input
rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are
installed*, through openings not furnished with doors, are considered a part of the unconfined space.
This fireplace shall not be installed in aconfined space or unusually tight construction unless provisions are provided
for adequatecombustion and ventilation air.
·Adjoining rooms are connecting only if there are doorless passageways or ventilation grills between them
UnusuallyTight Construction
The air that leaks arounddoors and windows may provide enough fresh air for combustion and ventilation. However,
in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction where:
a) walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one
perm (6x10
-11
kg per pa-sec-m
2
) or less with openings gasketed or sealed and
b) weather stripping has been added on windows that can be opened and on doors and
c) caulking or sealants are applied to areas such as joints around window and door frames, between sole platesand
floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at
other openings.
If your homemeets all of the threecriteria above, youmust provideadditional fresh air. See “Ventilation Air from
Outdoors”(page 8). If your home doesnot meet all of the three criteria above, proceedto “Determining Fresh-Air Flow
for Fireplace Location”.
DETERMINING FRESH-AIR FLOWFOR FIREPLACE LOCATION
Determining ifYou Have aConfined or Unconfined Space
Use this worksheet to determine if you havea confined or unconfined space.
Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passagewaysor
ventilation grills between the rooms.
1. Determine the volume of the space Length ×Width ×Height= cu. ft. (volume of space) Example: Space size 20 ft.
(length) ×16ft. (width) ×8 ft. (ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation toadjoining room is supplied with grills or openings, add the volume of these rooms to the
total volume of the space.

7
2. Divide the space volumeby 50 cu. ft.to determine the maximum BTU/hr the space can support.
__________(Volume of space) ÷50 cu. ft. = (Maximum BTU/hr the space can support)
Example: 2560 cu. ft. (volume of space) ÷50 cu. ft. = 51.2 or51,200 (maximum BTU/hr the spacecan support)
3. Add the BTU/hr of all fuel burning appliances in the space.
Vent-free fireplace _____________BTU/hr
Gas water fireplace* _____________BTU/hr
Gas furnace _____________BTU/hr
Vented gas fireplace _____________BTU/hr
Gas fireplace logs _____________BTU/hr
Other gas appliances*+BTU/hr
Total =_____________BTU/hr
*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the
outdoors.
4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.
__________BTU/hr (maximum the space can support)
__________BTU/hr (actual amount ofBTU/hr used).
Example: 51,200 BTU/hr (maximum the space can support)
56,000 BTU/hr (actual amount of BTU/hr used)
The space in the aboveexample is aconfined space becausethe actual BTU/hr used is more than the maximum
BTU/hr the space can support.
You must provide additional fresh air. Your options are as follows:
a) Rework worksheet, adding the spaceof anadjoining room. Ifthe extraspace providesan unconfined space,
removedoorto adjoiningroom or add ventilation grills between rooms. See “Ventilation Air from inside
Building,”page 8.
b) Vent room directly to the outdoors. See “Ventilation Air from Outdoors”, Page 8.
c) Install alower BTU/hr fireplace if lower BTU/hr size makes room unconfined. If the actual BTU/hr used is
less than the maximum BTU/hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the areain which thefireplace may be operated is smaller than thatdefined asan unconfined
space or ifthe buildingisof unusually tight construction, provide adequatecombustionand ventilation air byone
of the methods described in the National Fuel Gas Code,ANSI Z223.1/NFPA 54,Air for Combustion and
Ventilation, or applicablelocal codes.
WARNING: If the area in which the fireplace may be operated does not meet the required volume for indoor
combustion air, combustion and ventilation air shall be provided by one of the methods described in the
NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, the INTERNATIONAL FUEL GAS CODE, or applicable
local codes.
Example:
Gas water fireplace 30,000 BTU/hr
Vent-free fireplace + 26,000 BTU/hr
Total = 56,000 BTU/hr

8
Ventilation Air from Inside Building
This fresh air would come from adjoining
unconfined space. Whenventilating to an
adjoining unconfined space, you must
provide two permanent openings: one
within 12 inches of the wall connecting
the two spaces (see options 1 and 2,
Figure 2). You can also remove door into
adjoining room (see option 3, Figure 2).
Follow the National Fuel Gas Code NFPA
54/ANSI Z223.1. Air for Combustion and
Ventilation for required size of ventilation
grills or ducts.
Ventilation Air from Outdoors
Provide extra fresh air by using ventilation
grills or duct. You must provide two
permanent openings: one within 12 inches
of the ceilingand one within 12 inches of
the floor. Connect these items directly to
the outdoors or spaces open to the outdoors.
These spaces include attics and crawl spaces.
Follow the National Fuel Gas Code NFPA
54/ANSI Z223.1. Air for Combustion and
Ventilation for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for
inlet or outlet air into attic if attic has a
thermostat-controlled power vent. Heated
air entering the attic will activate the
power vent. Rework worksheet, adding the
space of theadjoining unconfined space. The
combined spaces must have enough fresh air to
supply all appliances in both spaces.
Figure 2 - Ventilation Airfrom Inside Building
Figure 3 - Ventilation Airfrom Outdoors

9
INSTALLATION
NOTICE: This fireplace is intended for use as supplemental heat. Use this fireplace along with your primary heating
system. Do not install this fireplace as your primary heat source. If you have a central heating system, you may run
system s circulating blower while using fireplace.This will help circulate the heat throughout the house.
WARNING: A qualified technician must install fireplace. Follow all local codes.
WARNING: Never install the fireplace:
·in a bedroom or bathroom
·in a recreational vehicle
·Where curtains, furniture, clothing, or other flammable objects are less than 42 inches from the front, top or sides
of the fireplace.
·in high traffic areas
·in windy or drafty areas
CAUTION: This fireplace creates warm air currents. These currents moveheat to wall surfaces next to fireplace.
Installing fireplace next tovinyl or cloth wall coverings or operating fireplacewhere impurities (such as tobacco smoke,
aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may cause walls to discolor.
WARNING: Maintain the minimum clearances. Ifyou can, provide greater clearances from floor, ceiling and adjoining
side and back walls.
IMPORTANT: Vent-free fireplaces add moisture to the air. Although this isbeneficial, installing fireplace in rooms without
enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation,
pages 6 through 8.
CLEARANCES TO COMBUSTIBLES
Carefully follow the instructions below. This fireplace is a wall mount unit designed to sit directly on the floor or on a
mantel base.
IMPORTANT: You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are
shown in Figure 4. Measure from outermost point of fireplace.
Minimum Wall and Ceiling Clearances (see Figure 4)
A. Clearances from outermost point of fireplace to any
combustible side wall should not be less than 7
inches.
B. Clearances from the fireplace to the ceiling should
not be less than 42 inches.
Figure 4 –Minimum Clearance to Wall
and Ceiling

10
NOTE: When fireplace is installed directly on carpeting, tile or other combustible material, other than wood flooring, the
fireplace must be installed on a metalor wood panel extending the full width and depthof the fireplace.
BUILT-IN FIREPLACE INSTALLATION
Built-in installation of this fireplace involves installing
fireplace intoa framed-in enclosure. This makes
the front of the fireplace flush with wall. If installing
a built-in mantel above the fireplace,you must
follow the clearances shown in Figure 5.
Follow the instructions.
NOTICE: Surface temperatures of adjacent walls
and mantelsbecome hotduring operation. Walls
and mantelsabove the fireboxmay become hot
to the touch.If installed properly, these temperatures
meet the requirement of the national product standard.
Follow all minimum clearances shown in this
manual. See Figure 6.
1. Frame in rough opening. Use dimensions shown in Figure 7
for the roughopening. If installing in a corner, use
dimensions shown in Figure 8 for the rough opening.
The height is 23.66(PC36VFC) & 28.11(PC32VFC), which is
the same asthe wall opening above.
2. Carefully set fireplace in front of roughopening with back of
fireplace inside wall opening.
3. Install gas piping to fireboxlocation. See Installing Gas Line,
on page 12 and Connecting to Gas Supply in log set
owner s manual.
Figure 5 –Clearance to Combustibles
Figure 6
Figure 7 - Rough Opening for Installing in Wall

11
IMPORTANT: When finishing your firebox,
Combustible materials such as wall board,
gypsum board, sheet rock, drywall, plywood,
etc, must have ½-in. clearance to the sides
and top of the firebox. Combustible
materials should never overlap the firebox
front facing.
WARNING: Do not allow any combustible
materials to overlap the fireboxfront facing.
WARNING: Do not allow combustible or
noncombustible materials to cover any
necessary openings like louvered slots.
WARNING: Never modify or cover the louvered slots on the front of the firebox.
Assembling Hood
CAUTION: Do not operate fireplacewithout hood in place.
Aim three holes on fireboxpanel at those on heat insulation board; fixthe fireboxwith screws pre-set on its board by
directly inserting screwdriver into holes on top fireboxpanel.
INSTALLING FIREBOX USING OPTIONAL ACCESSORY MANTELS
WARNING: A qualified service person must install firebox. Follow all local codes.
This fireboxmay be installed using a cabinet mantel accessory against a wall in your home. The fireboxand cabinet
mantel can be installed directly on the floor. A trim kit is included with the mantel accessories. Follow instructions with
mantel for installation.
Figure 8 - Rough Opening for Installing in Corner
Figure 9

12
INSTALLING GASLINE
NOTI CE:A qualified service person must connect heater to gas supply. Follow all local codes.
IMPORTANT: See Connecting to Gas Supply in your log set owner s manual for details on gas hookup.
You may run the gas line from either side of the firebox(see Figure 10). Decide which side you want to run the gas
line from.
Note: This is one optionfor installing shutoff valve. Check local codes for equipment shutoff valve location
requirements.
Using optional fiber panels
There is a gas knockout in each side panel for thegas line to feed through.Determine on which side the gas
connection will be located. Using a utility knife or cutting blade, remove the identified gas knockout.
CAUTION: Do not use excessive force to remove the knockout. Too much force may damage the fiber panel.
Figure 10
Figure 11
Equipment Shutoff
Valves (Install One)
Knock Out
Locations
(Knock Out
One Hole)
Gas Line Hole
KnockOut
Remove
This Area
1/2”Thick Liner
Firebrick Side Wall
Side View

13
REPLACEMENT PARTS
NOTE: Use only original replacementparts. This will protect your warranty coverage for parts replaced under
warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can t supply original replacement parts, call Customer Service toll
free at (1-877-886-5989) for referral information.
When calling Customer Service or your dealer, have ready:
·Your name
·Your address
·Model and serial number of your fireplace
·How fireplace was malfunctioning
·Purchase date
·Usually, we will ask you to return the defectivepart to the factory
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can t supply original replacement part(s) call Customer Service toll
free at (1-877-886-5989) for referral information.
When calling Customer Service have ready:
·Model number of your fireplace
·The replacement part number

14
PARTS LIST
This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under
Replacement Parts on 13of this manual.
Part.. Description Part # QTY
PC32VFC-132 (PC32VFC) 1
1 Screen Rod PC36VFC-132 (PC36VFC) 1
PC32VFC-131 (PC32VFC) 2
2 Draw screen PC36VFC-131 (PC36VFC) 2
PC32VFC-000B (PC32VFC) 1
3 Louver assembly PC36VFC-120B (PC36VFC) 1
4 Switch PF06-0400-A 1
5 Magnet FE32A155B 1
6 Blower fixing panel PC32VFC-127 1
7 Blower bracket PC32VFC-126 1
8 Blower Assembly FIB100 1
FBD32D201 1
9 Hood PC36VFC-117 1
Printed in China
9