Profile Mobile Call User manual

GSM Alarm System
MOBILE CALL
USER’S MANUAL
For a better understanding of this product, please read this user
manual throughly before using it.
Profile
Power Set Signal Alarm
ARM
STAY
CALL
SOS
1 2 3
4 5 6
7 8 9
0
ESC ENTER
System disarmed
00/00/00 00:00

CONTENTS
Features
Alarm Host Introduction
Initialization
System Settings
Enter Settings
Add Remote Controller
Delete Remote Controller
Coding of Defense Zone
Delete Defense Zone
Defense Zone Place Setting
Defense Zone Mode Setting
Siren Setting for Alarm
Alarm Delay Setting
Alarm Number Setting
Delete Alarm Number
SMS Number Setting
Delete SMS Number
Network Center Setting
Voice Recording
Record Play
System Date Setting
System Time Setting
Timely Arm Setting
Timely Disarm Setting
Wireless Control Setting
Wireless Siren Coding
1
2
4
4
4
5
5
6
7
7
8
9
9
10
10
11
11
12
12
12
13
14
14
15
15
16

Wireless Siren Encryption
Wireless Control for Home Appliance
Change Operate Password
Change Program Password
Arm Delay Time Setting
Alarm Delay Time Setting
Voice Prompt Function
Siren Prompt for Remote Controller
Backlight Setting
Siren Setting in “Emergency Help” Mode
SMS Reply for Arm/ Disarm
Language Setting
Factory Reset
Forget Password
Operation Instructions
Out Arm
Home Arm
Disarm
Answer Alarm Call
Remote Control
Emergency Help
System Dialing Function
Alarming Record Checking
Technical Parameters
Components List
Care and Maintenance
16
17
17
18
18
19
20
20
21
22
22
23
24
24
25
25
26
26
27
27
28
28
29
29
30
31

1
Features
Elegant and advanced touch keypad for easy operation;
128x64 lattice LCD screen with clock display;
4 wired and 10 wireless defense zones; each wireless zone supports
maximum 10 sensors;
Support maximum 8 remote controllers;
Built-in high-volume speaker, and artificial intelligent digital voice
announcer;
Built-in artificial intelligent English message;
10-second automatic voice message recording;
Can preset 6 phone numbers: when alarming, system will make audio
call to these numbers automatically;
Can preset 3 SMS numbers: when alarming, system will send SMS;
Timely arm and disarm;
Can be used as a wireless telephone by using keypad to make calls;
One-key-control: out arm, home arm, arm by remote controller or
phone call;
SOS, fire, gas, door, hall, window, balcony, and boundary places
alarm;
Real-time, delay, 24 hours, bypass defense zones programming
function;
Wireless learning code: easy to add additional wireless accessories;
Remote control the device to arm, disarm, monitor, and intercom by
phone;
Record checking: the device can store 30 alarm records;
Built-in LI battery: automatically recharge.
Different arm status: out arm, home arm, delay arm and timely arm;
Arm by different ways: panel keypad, remote controller, remote call;
Alarm call has the priority: even when the number of the device is busy;
Chapter 1. Features

Power Set Signal Alarm
ARM
STAY
CALL
SOS
1 2 3
4 5 6
7 8 9
0
ESC ENTER
System disarmed
00/00/00 00:00
2
Chapter 2. Alarm Host Introduction
3.
Alarm Host Introduction
2. Status LED
POWER: power and working status indicator.
-flashing quickly (once per second) means the system is searching
GSM network;
-
SET: it will be on when the system enters setting status.
SIGNAL: signal indicator.
ALARM: it will be on when the system is under alarm status.
1.
LCD screen: Resolution: 128x64; support English and Chinese display.
Touch keypad:
SOS: emergency alarm
ESC: clear the input content or back to last operation
ENTER: confirm
used to make call. Enter the number you want to call, and then
press this button. Press it during the phone call will hang up the
call.
ARM: press it; the system will enter OUT ARM status.
STAY: press it; the system will enter HOME ARM status.
CALL:
this keypad is Resistive Touch Panel which requires
press with certain strength. But please do not push it
heavily.
1
2
3
flashing once per 3 seconds means the system is under standby status.

3
4. Wired ports
1
SIREN+ Positive of siren (red cable)
Negative of siren (black cable)2 SIREN-
3 T_VCC Invalid port (does not have any function)
4
CLK Invalid port
5
DATA Invalid port
6
T_GND Invalid port
7
GND GND
8
Zone 1 Wired sensor 1: support both NO and NC
9
GND GND
10 Zone 2 Wired sensor 2: support both NO and NC
11
GND GND
12
Zone 3 Wired sensor 3: support both NO and NC
13 GND GND
14 Zone 4 Wired sensor 4: support both NO and NC
15 GND GND
5. Switch for internal battery.
6. SIM card slot:
Alarm Host Introduction
SIREN+ SIREN- T-Vcc CLK DATA T-GND GND Zonel GND Zone2 GND Zone3 GND Zone4 GND
10 11 12 13 14 15
1 2 3 4 5 6 7 8 9
OFF ON POWER IN
4
56
SIREN+ SIREN- T-Vcc CLK DATA T-GND GND Zone l GND Zone 2 GND Zone 3 GND Zone 4 GND
RED BLACK
SIREN WIRED SENSOR
Please pay attention to the direction arrow marked
on the slot: “LOCK” “OPEN”. Do not insert or take
out the SIM card when the main unit is power on.

4
Initialization
Chapter 3. Initialization
Correct initiation of the main panel is important to its normal working
and lifespan.
1. Connect the wired accessories that you need.
2. Insert SIM card.
3.
Chapter 4. System Settings
All the settings have to be done in setting status. Press 2/8/4/6 to turn
up/ down/ left/ right.
1. Enter Settings
Fig 1: disarm status
System disarmed
888888
Enter:
System disarmed
11/12/12 11:49
Remote control
Exit Enter
Fig 2: please enter password Fig 3: press ENTER to set
4. There will be a shoot beep after searching GSM network successfully.
The signal icon will display on the screen and the power status LED
will flash every 3 seconds.
Connect the power adaptor. The main panel will start self-inspection
and the POWER indicator LED will flash once. If this LED does not
light on, you need to restart the panel. Please do it at least 10
seconds later as repeated power on and off in short time is bad to
the panel's service life.
5. Turn on the battery switch.
6. Check the GSM signal icon on the LCD screen. Signal less than 3
lattice will affect the normal performance. Please put the main panel
at the place with good GSM signal.
Enter setting status: in the state of disarm, input 6-digit password
(system default: 888888), and then press ENTER. The main panel
makes a “beep” and SET indicator lights on. The screen shows remote
controller setting.

5
2. Add Remote Controller
This device supports maximum 8 remote controllers. Extra remote
controllers have to be coded to the host in order to perform normally.
Their code cannot be empty or the same with the saved code in the
host.
Method: enter remote controller setting menu, press “4” or “6” to
choose remote controller serial number, press “8” to find “coding” and
then press ENTER to confirm. Trigger the remote controller you want to
add, the panel will make two beeps after receiving it. And then press
ENTER to confirm. If the remote controller has been saved before, after
triggering it, the main unit will make four beeps and LCD screen display
“Error, Repeated code”.
Fig 1: enter remote control menu Fig 2: choose remote control serial
number and coding menu
Fig 3: waiting to receive signal
Fig 4A: recognize successfully Fig 4B: the host has the same code
with remote controller code
Fig 5: press ENTER to save
Remote control
Exit Enter
Operation figures:
Remote control 1
Exit Enter
Coding
Delete
Remote control 1
Back Save
000000000
Trigger code
Remote control 1
Back Save
077015192
Normal code
Remote control 1
Back Save
Error
Repeat code
Remote control 1
Save completed
If the remote controller is lost or damaged, it should be deleted. After
deletion, it cannot control the main panel.
3. Delete Remote Controller
System Settings

6
System Settings
Fig 1: enter remote controller
setting
Fig 2: choose the controller you
want to delete
Fig 3: press ENTER to confirm
Method: enter remote controller setting menu, press “4” or “6” to
choose the remote controller you want to delete. Press “8” to find
“delete”, and then press ENTER.
Operation figures:
Remote control 1
Delete completed
Remote control 1
Exit Enter
Coding
Delete
Remote control
Exit Enter
This alarm system has 10 wireless defense zones, each of which
supports up to 10 wireless detectors. Extra sensors not in the standard
package have to be coded to the host in order to perform normally. Their
code cannot be empty or the same with the saved code in the host.
Method: enter defense zone setting menu, press “4” or “6” to choose
zone number, press “8” to find “coding” and then press ENTER to
confirm. Trigger the sensor you want to add, the panel will make two
beeps after receiving it. And then press ENTER to confirm. If the
sensor has been saved before, after triggering it, the main unit will
make four beeps and LCD screen display “Error, Repeated code”.
Operation figures:
Fig 1: enter defense zone setting Fig 2: choose zone number and
press ENTER
Fig 3: waiting signal from sensor
Back Save
000000000
Trigger sensor
Zone 1Zone 1
Exit Enter
Coding
Delete
Zone
Enter
Exit
4. Coding of Defense Zone

7
System Settings
Fig 4A: recognize successfully Fig 4B: the host has the same
code with sensor code
Fig 5: press ENTER to save
Back Save
Error
Repeat code
Zone 1
Back Save
241015162
Normal code
Zone 1
Save completed
Zone 1
5. Delete Defense Zone
The wireless detector can't control the main unit after it's deleted.
Method: enter defense zone setting menu, press “4” or “6” to choose
the sensor you want to delete. Press “8” to find “delete”, and then
press ENTER.
6. Defense Zone Place Setting
The location of defense zone can be set in the main panel, so that the
panel can send correspondent alarm message. There are 8 locations
for alarm: SOS, fire, gas, door, hall, window, balcony, and boundary.
Please refer to “Chapter 6. Technical Parameters” for system default
settings.
Operation figures:
Exit
Coding
Delete
Zone 1
Enter
Zone
Enter
Exit
Method: enter defense zone setting menu, press “4” or “6” to choose
the zone number, and then press “2” or “8” to enter zone place menu.
Press ENTER will shift the places.
Delete completed
Zone 1
Fig 1: enter defense zone setting Fig 2: choose zone number Fig 3: choose Delete and press
ENTER

8
System Settings
Operation figures:
Back Enter
Place: Fire
Armed: Enable
Zone 1
Back Enter
Place: GAS
Armed: Enable
Zone 1
Zone
Enter
Exit
Fig 1: enter defense zone setting Fig 2: choose defense zone place Fig 3: press ENTER to confirm
Fig 4: (this example)
Before setting, the alarm SMS for zone 1 is: 01zone fire alarm;
After setting, it is: 01 zone gas alarm.
The format of alarm SMS: [01~10] zone [place] alarm. For example,
you set the place of zone 4 as “window”. The alarm SMS you receive
is: 04 zone window alarm.
7. Defense Zone Mode Setting
There are different defense zone modes: out arm, home arm, alarm
under disarm mode. For example, you need gas detectors working all
the time, please set ARM, HOME, and DISARM as enabled.
Method: enter defense zone setting menu, press “2” or “8” to choose
HOME arm status (enable or disable), press ENTER to confirm.
Setting methods for OUT arm and DISARM are the same.
Operation figures:
Fig 1: enter defense zone setting Fig 2: choose mode Fig 3: press ENTER to confirm
Back Enter
HOME: Disable
Disarmed: Disable
Zone 1
Back Enter
Zone 1
Disarmed: Disable
HOME: Enable
Zone
Enter
Exit
Fig 4: (this example)
Before setting, zone 1 does not alarm in home arm status;
After setting, it will alarm when triggered in home arm status.

Back Enter
Zone 1
Delay: Disable
Siren: Enable
Back Enter
Siren: Disable
Delay: Disable
Zone 1
Back Enter
Zone 1
Delay: Disable
Siren: Enable
Back Enter
Siren: Disable
Delay: Disable
Zone 1
19
System Settings
8. Siren Setting for Alarm
The siren can be set on or off when there's alarm from each defense
zone.
Fig 1: enter defense zone setting Fig 2: choose siren status Fig 3: press ENTER to confirm
Fig 4: (this example)
Before setting, the siren is on when zone 1 alarms;
After setting, siren will not sound when zone 1 alarms.
9. Alarm Delay Setting
Alarm delay: the main panel will make alarm call and the siren will ring
after the preset delay time.
Fig 1: enter defense zone setting Fig 2: choose delay status Fig 3: press ENTER to confirm
Fig 4: (this example)
Before setting, the panel makes alarm and the siren rings immediately when zone 1 is triggered;
After setting, alarm will be after the preset time. (set the delay time under system setting)
Zone
Enter
Exit
Zone
Enter
Exit
Method: enter defense zone setting, press “2” or “8” to choose siren
enable or disable, and then press ENTER to confirm.
Method: enter defense zone setting, press “2” or “8” to choose delay
enable or disable, and then press ENTER to confirm.
Operation figures:
Operation figures:

Phone number
Exit Enter
10
System Settings
10. Alarm Number Setting
This system can store 6 alarm phone numbers. When alarming, it will
make alarm call to these numbers in order for three times
automatically, until someone gets through the call.
Method: enter phone number setting menu, press “4” or “6” to choose
serial number and then press ENTER. Input the number you want to
set, then press ENTER to save.
Operation figures:
Fig 1: enter phone number setting Fig 2: choose serial NO. Fig 3: input phone number
Fig 4: press ENTER to save Fig 5: the 1st number is set
successfully
11. Delete Alarm Number
Method: enter phone number setting, press “4” or “6” to choose serial
number, then press “8” to choose “delete” and then press ENTER to confirm.
Operation figures:
Fig 1: enter phone number setting
menu
Fig 2: choose the number you
want to delete
Fig 3: choose “delete”
Phone 1
Back Enter
No number
Delete
Back Save
123456789
Input phone number
Phone 1
Phone 1
Save completed
Phone number
Exit Enter
Phone 1
Back
123456789#
Delete
Enter
Phone 1
123456789#
Delete
Back Enter
Phone 1
Delete
Back Enter
123456789#

Save completed
SMS 1
11
Fig 4: the 1st number is deleted
Delete completed
Phone 1
12. SMS Number Setting
This system can store 3 SMS receiving phone numbers. When
alarming, it will send SMS to these numbers.
Method: enter SMS number setting, press “4” or “6” to choose serial
number and then press ENTER. Input the number you want to set,
then press ENTER to save.
Operation figures:
Fig 1: enter SMS number setting Fig 2: choose serial number and
press ENTER
Fig 3: input SMS receiving number
Fig 4: press ENTER to save
SMS 1
Back Enter
No number
Delete
Back
13812345678
Input phone number
SMS 1
Save
SMS number
Exit Enter
13. Delete SMS Number
Method: enter SMS number setting, press “4” or “6” to choose serial
number, then press “8” to choose “delete” and then press ENTER to
confirm.
System Settings

Back Enter
123456789#
Delete
SMS 1
Delete completed
SMS 1
Back
13812345678#
Delete
SMS 1
Enter
12
Operation figures:
Fig 1: enter SMS number setting Fig 2: choose the number you
want to delete
Fig 3: choose “delete”
Fig 4: the 1st number is deleted
SMS number
Exit Enter
14. Network Center Setting
System Settings
This system does not have this function at present. Please kindly
contact us if needed.
15. Voice Recording
This system can make 10-second voice record. When alarming, it will
make call and play this record.
Operation figures:
Fig 1: enter record setting Fig 2: start recording Fig 3: record for 10 seconds
Method: enter record setting, and start by choosing “start recording”. It
will stop automatically 10 seconds later.
Recording
Exit Enter Back Enter
Start recording
Recording
Back
05
Recording
Enter
16. Record Play

Save completed
Date
Back Save
00/00/00
Please enter
Date
Back Enter
11/12/12
Date
Enter
Time
Exit
13
Operation figures:
Fig 1: enter record setting Fig 2: you'll see this menu Fig 3: press “6” to choose “play”
Fig 4: press ENTER to play the record
17. System Date Setting
Method: enter “Time” menu, and then choose “Date”. Input the exact
date you want to set and press ENTER to confirm.
Operation figures:
Fig 1: enter time setting menu Fig 2: choose date setting menu Fig 3: input the date
Fig 4: press ENTER to save
Recording
Exit Enter Back Enter
Start recording
Recording
Back
Play
Recording
Enter
Back
05
Recording
Enter
The date format is year/ month/ day. (“Year” setting is from 00-99.)
System Settings
Enter record setting, and then press “6” to choose “play”. The panel will
start playing the voice message you recorded. You can re-record if
you're not satisfied with it.

Back Enter
11/12/12
Date
Back Enter
Timely arm
Disable
Back Enter
11/12/12
Date
Back Enter
Time
16:25
Back Save
00:00
Please enter
Time
Save completed
Time
14
18. System Time Setting
Time in this alarm system is 24-hour system. Enter “Time” menu, you
will see “Date” menu, then press “6” to choose “Time”. Input the exact
time you want to set and press ENTER to confirm.
Operation figures:
Fig 1: enter time setting menu Fig 2: you'll see date setting menu Fig 3: press “6” to choose “time”
Fig 4: input the time Fig 5: press ENTER to save
19. Timely Arm Setting
After this setting, the alarm system will start arm status at the preset
time.
Operation figures:
Enter
Time
Exit
Method: enter “Time” menu, you will see “Date” menu, then press “6” to
choose “Timely arm”. Input the exact time you want to set and press
ENTER to confirm.
Fig 1: enter time setting menu Fig 2: you'll see date setting menu Fig 3: press “6” to choose
“timely arm”
Enter
Time
Exit
System Settings

Save completed
Timely disarm
Back Enter
Timely disarm
Disable
Back Enter
11/12/12
Date
15
Fig 4: input the time you want
to set
Save completed
Timely arm
Enter
Time
Exit
20. Timely Disarm Setting
After this setting, the alarm system will disarm automatically at the
preset time.
Fig 1: enter time setting menu Fig 2: you'll see date setting menu Fig 3: press “6” to choose
“timely disarm”
Fig 4: input the time you want
to set
21. Wireless Control Setting
This system does not have this function at present. Please kindly
contact us if needed.
System Settings
Method: enter “Time” menu, you will see “Date” menu, then press “6” to
choose “Timely disarm”. Input the exact time you want to set and press
ENTER to confirm.
Operation figures:

16
22. Wireless Siren Coding
Wireless sirens have to be coded to the main panel in order to work
normally.
Method: set the wireless siren which you want to code in coding status.
Then enter “wireless control” menu in this panel, you'll see “control”
menu. Press “6” to choose “wireless siren” setting, and then enter
“transmission” setting. The panel will send a wireless signal to the
siren.
Operation figures:
Fig 1: enter Wireless Control
menu
Fig2: control menu Fig3: Press “6” to choose
Wireless siren
Fig 4:
After pressing ENTER key, the main unit will transmit a wireless signal to control the wireless siren.
Back Enter
Transmission
Wireless siren
Encryption
Back Enter
Enable
Control
Wireless Control
Enter
Exit
23. Wireless Siren Encryption
The signal used to code with the wireless siren is sent from the internal
System Settings
transmitter of the main panel. The signal codes of this model from our
company are the same. If you and your neighbor both are using this
model, the alarm signal from your neighbor may cause your siren
sound. So it is recommended to encrypt the wireless siren to avoid the
interference.
Method: enter “wireless control” menu, and then “control” menu. Press
“6” to choose “wireless siren”, then press “8” to choose “encryption”.
Input 4 numbers randomly and then save it.

17
Fig 1: enter wireless control
menu
Fig 2: control menu Fig 3: press “6” to choose
wireless siren
Fig 4: input 4 numbers randomly Fig 5: press ENTER to save
Operation figures:
Wireless Control
Enter
Exit Back Enter
Disable
Control
Back Enter
Enable
Wireless siren
Encryption
Back Enter
8907
Wireless siren
Please input
Save completed
Wireless siren
24. Wireless Control for Home Appliance
It does not have this function at present. Please kindly contact us if
needed.
Operate password is used for daily use (disarm or remote control).
System default is 1234.
25. Change Operate Password
System Settings
Back Save
4545
Please input
Operate password
Back Enter
1234
Operate password
Settings
Exit Enter
Method to change this password: enter “settings” menu, and then
“operate password”. Input the 4-digit password you want to set, and
save it.
Fig 2: enter operate password
menu
Fig 1: enter settings menu Fig 3: input the 4-digit password
Operation figures: