progeo EXELLE VARIO Classic User manual

ENGLISH - rev. 0 –2021/05
User’s manual
ULTRA-LIGHT FOLDING WHEELCHAIR WITH CROSSBAR SYSTEM
EXELLE VARIO
Classic

Exelle Vario Classic 2

Exelle Vario Classic 3
CONTENTS
Some of the images in this manual may show a wheelchair model different from the reference one.
However, all instructions are applicable, regardless of the model differences.
Total or partial reproduction of this manual is forbidden without written authorisation from Rehateam
s.r.l.
INTRODUCTION .........................................................................................4
FLAMMABILITY........................................................................................................ 5
SYMBOLS USED ..................................................................................................... 5
PRODUCT LABELS ................................................................................................. 5
1INTENDED PURPOSES AND CONDITIONS OF USE................................. 6
2PUTTING THE WHEELCHAIR INTO SERVICE AND REGULAR USE ........ 7
2.1 Tyre pressure................................................................................................ 8
2.2 Brakes .......................................................................................................... 9
2.3 Quick release rear wheels .......................................................................... 10
2.4 Apertura/chiusura della carrozzina ............................................................. 11
2.5 Footrests..................................................................................................... 12
2.6 Front frame with removable footrest ........................................................... 13
2.7 Calf strap .................................................................................................... 14
2.8 Adjustable backrest upholstery................................................................... 14
2.9 Armrests ..................................................................................................... 15
2.10 Fasteners.................................................................................................... 17
2.11 Wheelchair lifetime ..................................................................................... 17
3SAFETY...................................................................................................... 18
3.1 Accident prevention .................................................................................... 18
3.2 Transfers: getting in and out of the wheelchair ........................................... 19
3.3 Starting to drive your wheelchair................................................................. 20
3.4 Negotiating obstacles: steps and stairs ...................................................... 21
3.5 Negotiating slopes or inclines ..................................................................... 23
3.6 Ensuring stability......................................................................................... 24
4TRASPORT OF THE WHEELCHAIR.......................................................... 25
5GENERAL DESCRIPTION OF PARTS....................................................... 26
6ADJUSTMENTS.......................................................................................... 27
7ACCESSORIES .......................................................................................... 28
7.1 Narrow passage transit wheels................................................................... 28
7.2 Anti-tip wheel .............................................................................................. 28
7.3 Tipping aid .................................................................................................. 29
7.4 Pelvic belt and harness............................................................................... 30
7.5 Headrest ..................................................................................................... 31
7.6 Rear wheels / tyres / hand rims................................................................... 31
7.7 Clothing guards........................................................................................... 31
8MAINTENANCE.......................................................................................... 32
8.1 Replacement of worn parts......................................................................... 33
8.2 Inspection of components........................................................................... 33
8.3 Disinfection and reuse of the wheelchair .................................................... 34
8.4 Storage ....................................................................................................... 34
8.5 Disposal/recycling of materials ................................................................... 34
8.6 Troubleshooting guide ................................................................................ 35
9TECHNICAL SPECIFICATIONS................................................................. 36
10 WARRANTY ............................................................................................... 37

Exelle Vario Classic 4
INTRODUCTION
At Rehateam, constant research into quality and creativity are the cornerstone of our business.
After many years in the industry, we remain genuinely focused on providing total customer satisfaction while bringing innovative style and design to every one of our high-quality wheelchairs.
We have become industry leaders by making excellence and service our top priorities, building all our models from carefully selected materials and providing multiple configurations to enable the utmost
personalisation according to specific user needs.
We perform continuous, meticulous quality control and our testing procedures offer the highest possible quality combined with fast, reliable service.
We acknowledge that we owe our success to our customers and all who have believed in us and helped us establish that quality is the supreme differentiator.
FOR THE DEALER
This manual MUST be provided to the occupant of this wheelchair.
BEFORE giving the wheelchair to the occupant, the dealer MUST carry out a general check of all its fittings and check its functionality.
After this check, the dealer should complete the warranty certificate on the last page by applying the stamp of the company or represented organisation together with name, signature, and date.
This certificate must be retained by the occupant.
If the company’s stamp and signature on the warranty certificate is missing, the product warranty is void.
This product is intended for disabled occupants with intact visual, cognitive and reading abilities.
If some or all of these abilities are limited or impaired, the presence of an assistant person with appropriate abilities is always required.
This document is also available in PDF format for the visually impaired at www.rehateamprogeo.com.
FOR THE OCCUPANT and/or CARER
BEFORE using this wheelchair, please READ all parts of this manual and keep it for future reference.
Check that the warranty certificate has been fully compiled by the dealer and keep it with care.
This document is also available in PDF format for the visually impaired at www.rehateamprogeo.com.

Exelle Vario Classic 5
FLAMMABILITY
This product has been tested in accordance with the standard EN12183. This standard also includes a flammability test.
SYMBOLS USED
This symbol indicates a potentially hazardous situation, which, if not avoided, can
result in death or serious personal injury.
This symbol indicates a forbidden action.
This symbol indicates a potentially hazardous situation, which, if not avoided, may
cause minor personal injuries or property damage.
This symbol indicates important instructions or special information.
PRODUCT LABELS
Year/month of production
UDI code (Unique Device
Identification)
Progeo brand logo
Serial number
Read the user’s manual
XXXXXXX
Product name
Ambient usage
temperature
Crash-test approved
Maximum weight load
Not crash tested
Manufacturer data
CE mark
Maximum slope in use
MD mark
(Medical Device)
XXXXXXXXXXXXXXX

Exelle Vario Classic 6
1 INTENDED PURPOSES AND CONDITIONS OF USE
This model is a self-propelled wheelchair which means that it can be moved manually by driving the hand rims on the rear wheels or by an assistant using the push handles.
It may be used for both rehabilitative and active purposes and is therefore suitable for daily use by both occupants with severe disabilities (with limited movement of the legs, arms or torso) and "active"
occupants (capable of carrying out activities independently). It is used to assure the independent mobility or assisted movement of an occupant with reduced or no use of one or more parts of the body.
Given the ample range of possible accessories and configurations, the wheelchair can be used safely both indoors (flat, gym, school, library, etc.) and outdoors (street, pavement, yard, etc.) with ambient
temperatures between -30 and +60 °C.
If the occupant is affected by particularly severe disabilities or unable to move autonomously, the help of an assistant is always advisable. We also discourage use over hilly, particularly soft, sandy or uneven
ground, on slopes exceeding the recommended gradient and in acidic environments.
During daily use of the wheelchair, the occupant may come across situations such as rough or irregular terrains (gravel, cobblestones, holes on the ground, etc.) or slippery terrain
(wet, sandy, dusty, oily hard surfaces, etc.). In all such situations and, in general, in all cases where use of the wheelchair may be difficult or risky (for the wheelchair and its
occupant), it is always advisable to move carefully and smoothly without sudden acceleration or hard braking.
When the difficulty or risk is high, the help of an assistant is always advisable.
The maximum slope that can be negotiated to prevent the wheelchair from tipping over backwards is 3° (6%).
All footrests require the occupant to wear socks or shoes, so do not rest bare feet on them.
The seating surface, in cloth or other material if available for this model, is not designed to be directly sat on by the occupant; it is therefore necessary to provide a cushion for the
occupant to sit on and which must be ordered separately according to the occupant’s specific needs.
Maximum weight load for the model EXELLE VARIO: 125 kg.
In certain configurations, the wheelchair may exceed 700 mm in width. In such cases, under certain circumstances, it may not be possible to use some or all of the available escape
routes from a building. If the wheelchair configuration causes the wheelchair width to exceed 700 mm, it may be difficult or impossible to travel on public transport.
EXELLE VARIO Given its dimensional and structural characteristics, the wheelchair model is ideal for use by both teenagers and adults.

Exelle Vario Classic 7
2 PUTTING THE WHEELCHAIR INTO SERVICE AND REGULAR USE
It is important that all the wheelchair’s functional parts are CHECKED ONLY BY QUALIFIED AND AUTHORISED PERSONNEL, both to assess its suitability and to provide the correct
instructions for use to occupant and assistant where applicable.
If any part of the wheelchair is found to be defective, the occupant or assistant must consult the dealer to solve the problem.
Non-observance of the indications/instructions in this manual may lead to malfunctions and/or damage to the wheelchair and/or the occupant and/or third parties. Rehateam is not
liable for any damage to the wheelchair and/or the occupant and/or third parties caused by or resulting from the non-observance of the indications/instructions.
Use of the wheelchair requires some of its parts to be handled. Instructions for the correct handling of the wheelchair’s components are provided in the corresponding sections of
this document. Please follow these instructions to avoid injuries.
The installation and use of electrification, mechanical and/or electrical drive devices or any other accessory not provided by Rehateam s.r.l. at the time of delivery may result in
stresses that were not foreseen during product testing and therefore the integrity and complete safety of the product is not guaranteed. In case of installation of any additional
accessory to the product delivered by Rehateam s.r.l., the latter must be guaranteed by your dealer, the accessory device manufacturer, and approved by Rehateam s.r.l.

Exelle Vario Classic 8
2.1 Tyre pressure
The tyres must always be well inflated to ensure that the wheelchair brakes and rolls properly.
Use your fingers to remove the plastic cap which covers the inflation valve on the rim of the rear wheels.
Use a compressor or pump equipped with a pressure gauge to bring the pressure up to the correct level. Screw the plastic cap back on.
Check for correct tyre pressure on a weekly basis as indicated on the tyre (an intermediate value between min. and max. is recommended).
Proper tyre pressure makes the wheelchair considerably smoother and more controllable to manoeuvre.
Inadequate tyre pressure (especially if lower than prescribed) degrades the effectiveness of the parking brakes (the wheelchair may not remain stationary).
Do not exceed the pressure indicated on the tyre because you may damage the tyre and the inner tube.
Always respect what indicated on the tyre.
The front castors may also be of the "pneumatic" type; in this case, follow the same instructions.
Solid tyres do not require any inflation. This type of tyre requires less maintenance and reduces puncture repair or replacement costs. Compared to tubed or tubular tyres, they are not as smooth
during normal use and absorb less vibration when rolling on uneven ground.

Exelle Vario Classic 9
2.2 Brakes
The parking brakes are a safety device and their efficiency must be checked daily.
The pressure brake acts directly on the tyre by means of a lever, which is why braking efficiency depends on correct tyre inflation pressure.
We recommend that you check your tyre pressure regularly to ensure that it is always correct.
The maximum safe gradient for the parking brakes to work properly is 3° (6%).
The parking brake is a safety device, and you must not use it while the wheelchair is moving as this could cause the wheelchair to overturn with possible injury to the occupant.
To check the effectiveness of the brakes, apply them as described below depending on the type of brake, and, with the person sitting in the wheelchair, try to gently push the wheelchair.
If the rear wheels do not turn or if they turn with great difficulty and still prevent unintentional movement of the wheelchair, the parking brakes are acting as required.
Check both brakes. Applying and releasing the parking brake may require more or less force depending on the type of brake chosen.
Occupants with reduced upper limb strength should use the extended lever.
Take care not to pinch/crush your fingers when applying and releasing the brakes, but also in any other situation where your hands come close to the brakes.
PULL-TO-LOCK BRAKE
To engage the brake, pull the lever backward until it locks.
To release the brake, push the lever frontward.
The brake automatically returns to its resting position.

Exelle Vario Classic 10
2.3 Quick release rear wheels
The rear quick release wheels enable you to reduce the wheelchair’s bulk and save space, thus facilitating storage in the car or, if the wheelchair is equipped with the "narrow passage wheels" accessory, to
reduce its width and length in order to access narrow spaces.
Check that the quick release pins on the rear wheels are correctly engaged without anyone sitting on the wheelchair.
The parking brakes must be released.
Raise the rear wheel by lifting the wheelchair slightly off the ground and grasping the backrest post handle.
Grasp the rear wheel hub with your hand (without pressing down on the release pin), taking care to avoid inserting your fingers between the spokes.
Push and pull the wheel (as indicated by the arrow) to check that it fits properly: the wheel must not come off.
If the wheel comes off during this check, the axle must be adjusted.
Adjustment should only be carried out by qualified and authorised personnel.
Checking the rear wheel pins is one of the procedures that the occupant should perform periodically.
If the pins are not properly fitted, the rear wheel may come off during use, resulting in the wheelchair tipping over and possible injury to the occupant.
To remove the wheel, first release the parking brakes.
Lift the wheelchair wheel slightly off the ground, using one hand to grasp the backrest knob to facilitate the operation.
Grasp the wheel by the spokes around the hub, press the release pin button with your thumb and, without releasing, extract the wheel fully.
To fit the wheel, first release the brake.
Slightly lift the wheelchair form the ground on one side by the backrest knob.
With your hand, take hold of the rear wheel’s hub and, with your thumb, press the button of the quick release pin, keep it pressed and push the pin fully into its seat.
Release the axle quick release pin button (a click indicates correct engagement).
Always release the brake before removing and inserting the rear wheel.
Always check the correct engagement of the quick release axles.
The holes for the rear wheel positioning may pinch or crush your fingers. Take care whenever your hands are close to such holes.

Exelle Vario Classic 11
2.4 Apertura/chiusura della carrozzina
Questo modello permette la chiusura della carrozzina agendo sulla crociera.
1 APERTURA
Appoggiare il palmo delle mani sopra i due tubi del sedile, posizione Ae B, e spingere con forza verso il basso fino alla completa apertura.
Dopo aver aperto la carrozzina controllare con molta attenzione che i tubi della crociera siano sempre ben inseriti nei quattro supporti S.
Eseguire l’operazione facendo molta attenzione che le dita della mano, durante la fase di apertura, non finiscano tra il tubo della seduta ed i supporti o tra il tubo della seduta ed il
tubo del telaio.
Per facilitare l’operazione è preferibile alzare leggermente una ruota posteriore in modo che l’attrito sul pavimento non la tenga bloccata. A tale scopo, afferrare una delle manopole poste sullo schienale e
sollevare leggermente la carrozzina. Con la mano libera, premere con forza verso il basso in corrispondenza dei tubi sedile. Controllare che i tubi del sedile siano inseriti negli appositi supporti in modo
corretto.
Abbassare la pedana poggiapiedi (questa operazione non è necessaria se è montata una pedana unica a libro).
2 CHIUSURA
Rimuovere il cuscino o eventuali altri supporti morbidi e rigidi dal sedile o dallo schienale.
Alzare la pedana o le pedane (questa operazione non è necessaria se è montata una pedana unica a libro).
Tirare con le due mani la tela sedile verso l’alto come mostrato nelle immagini.
B
A
1
2
S

Exelle Vario Classic 12
2.5 Footrests
When transferring to and from the wheelchair, never keep your feet on the footrest; excessive weight on the footrest may result in harm to the occupant.
After each operation, check that the footrest is always in the correct operating position.
Dual footrests are less resistant than the single version and they are therefore not suitable for occupants subject to strong spasms and/or contractions.
When raised, footrests enable occupants to rest their feet on the ground more easily, especially when moving in and out of the
wheelchair.
Flipping up the footrest is a very easy operation you can perform with one hand by pulling the footrest plate upward.
To put the footrest back to the operating position, just push it down.
DUAL FOOTREST
Make sure both footrests are fully lowered before using the wheelchair.
OTHER INFORMATION ON FOOTREST
To comply with the rule UNI EN 12183 paragraph 6.1, when dual footrests are fitted, it is necessary to maintain the correct
clearance between the two footrest plates when lowered:
1) The footrest clearance (C) must not exceed 35 mm for wheelchairs used by adults (1).
2) The footrest clearance (C) must not exceed 25 mm for wheelchairs used by children (2).
Here image on the side shows the correct dual footrest size (B) with respect to seat width (A):
A
1
2
B
B
27
---
140 x 160
30
---
140 x 160
33
140 x 160
150 x 160
36
150 x 160
170 x 160
39
170 x 160
170 x 160
42
170 x 160
---
45
200 x 160
---
48
200 x 160
---

Exelle Vario Classic 13
2.6 Front frame with removable footrest
One of the features of this model is the particular footrest that you can rotate out of the way or remove completely.
These functions reduce the bulk and the weight of the wheelchair and help the occupant to get closer to objects such beds and tables.
It is also convenient for amputees who have no use for the footrest.
(1) Check that the footrest frame is securely locked to its support.
With one hand, take hold of the footrest frame and try to move it clock and anticlockwise. If it is securely locked, the footrest frame will not rotate, but you should notice just a little play.
(2) To swing the footrest frame externally, move the lever Asideward to same direction and turn the footrest frame.
(3) To swing the footrest frame internally, move the lever Asideward to same direction and turn the footrest frame.
(4) To lock the footrest frame to the operating position, swing it to the central position until it locks automatically. A click will indicate it has locked properly.
Check for proper locking as described previously.
(5) To remove the footrest frame, move the lever Afrontward and pull the footrest frame up until the axle Bcomes out of the post C. Finally, remove the footrest frame.
(6) To insert the footrest frame, first lean the fork Don the post C.
Then, lower the footrest frame until the axle Bslides into the post C.
If necessary, swing the footrest frame to the middle until it automatically locks. A click will indicate it has correctly locked (the lever Amoves automatically to the locking position).
If the wheelchair is equipped with a single footrest, it must always be raised before swinging the footrest away.
If the wheelchair is equipped with a dual footrest, it must be raised only if the footrest is swung inwards.
A
1
2
A
3
click
4
5
A
6
B C
C D
B C
click

Exelle Vario Classic 14
2.7 Calf strap
In some cases, according to the castor’s size and to the wheelchair’s width, the castor, while turning on the fork’s axle, may
touch the occupant’s heel.
To prevent such contact that may lead to overbalancing, the wheelchair is provided with a calf strap. The calf strap should be
adjusted in such a way that the occupant’s feet never touch the castors.
You can easily adjust the calf strap using the provided Velcro straps.
2.8 Adjustable backrest upholstery
The backrest can be adjusted to the occupant requirements by tensioning or slackening the two special Velcro straps fitted inside the backrest
itself.
To carry out the adjustment, lift or remove the upholstery, tighten, or slacken the Velcro straps as required and replace the upholstery.
If the wheelchair is provided with a postural backrest, follow the instructions of the postural system.
The combination of the inclination of the seat with the inclination of the backrest posts and the inclination of a postural backrest with respect to the posts, could result in an angle
greater than 25° with respect to the vertical. In that case, the wheelchair must have a headrest or arrangement to secure it as intended for this model.
>25°

Exelle Vario Classic 15
2.9 Armrests
This model can be equipped with armrests.
The armrests are considered as an accessory and they should be ordered separately.
They are particularly useful for people with reduced hand or arm mobility and for occupants with limited upper body movement who require better stability once seated in the wheelchair.
Do not use the armrest as a hand hold to raise the wheelchair; this may cause the armrests to come off from their supports, damaging the wheelchair and harming the occupant.
Do not use the armrest for support when transferring to or from the wheelchair.
On the contrary, we recommend removing the armrest on the transfer side to facilitate the manoeuvre.
Armrest pads may contain phthalates that are potentially hazardous to health if ingested. Avoid scratching the padding and putting any residue on your fingers into your
mouth or, worse still, nibbling or sucking on the padding itself (as may occur with children).

Exelle Vario Classic 16
DESK ARMREST
This type of armrest is very practical and can be swung away or removed completely, making it much easier to move the wheelchair and transport it.
In addition, the Desk armrest includes a straight clothing guard.
Always check the armrests are securely locked in their using position shown as P.
Otherwise, the armrest may accidentally disengage and the occupant may fall from the wheelchair.
(1) To check that the armrest is in the correct operating position, take hold of the armrest’s pad with one hand and try to pull it up.
If correctly secured, the armrest will not come off the support A and the pad itself will not move.
(2) (3) (4) To remove the armrest, first lower the lever B, then, take hold of the armrest’s pad and pull it off.
To secure the armrest in the operating position, first, make sure the lever Ais lowered (3). Then, insert the post C(4) into the support A.
Finally, raise the lever B (5). Check that the armrest is securely locked as described above.
The occupant can also easily adjust the armrest height.
(6) Turn the lever Dby 90° (7) and then pull the pad up or push it down to the desired height.
After adjustment, turn the lever Duntil it locks in one of the holes of post C (8).
P
D
D
C
6 7 8
B
B
C
A
A
1234 5
B

Exelle Vario Classic 17
2.10 Fasteners
When delivered to the occupant, the wheelchair is checked by the retailer who thus ensures it is in perfect condition.
However, daily use of the wheelchair may cause bolts and nuts to loosen.
We recommend checking that all hardware is correctlytightenedatleast oncea month.
If necessary, consult an authorised PROGEO dealer or technician for maintenance assistance.
At each maintenance cycle, ensure that all nuts, bolts, and screws are correctly tightened.
Failure to observe this warning could result in damage to the occupant, third parties or the vehicle, for which Rehateam s.r.l. shall not be liable.
2.11 Wheelchair lifetime
PROGEO wheelchairs are used on a daily basis and they are consequently subject to continuous stress that causes inevitable wear and tear of the parts.
With this in mind, PROGEO wheelchairs have a lifetime of 5 years provided they receive thorough periodic maintenance.
The lifetime will be considerably extended if the wheelchair is used only indoors or not on daily basis.

Exelle Vario Classic 18
3 SAFETY
The Progeo wheelchair is a medical device and therefore it MUST NOT BE LENT NOR GIVEN TO OTHER USERS, even for short period.
It is forbidden to make any unauthorised modifications or use un-approved parts that may change the wheelchair structure and create an unsafe condition or possible harm to the
wheelchair and occupant.
Rehateam s.r.l. will not be liable for failure to comply with the instructions or recommendations set out in this manual and any such activity will result in the immediate
cancellation of the manufacturer's warranty.
BURN HAZARD! Wheelchair components may heat up if they are exposed to strong sunlight.
Notify the manufacturer in the event of serious accidents in relation to the device.
Manufacturer: Rehateam s.r.l., Vicolo Negrelli 5, 31038 Castagnole di Paese TV, Italy, tel. [phone], mail: [e-mail]
3.1 Accident prevention
MOVEMENTS
Avoid sudden, jerky movements when using the wheelchair asthiscouldcauseit to overbalance. If your path is obstructed by obstacles, avoid sudden movements (such as abrupt braking).
There is increased risk of skidding on irregular or damp ground.
Passing over obstacles as steps and ramps should be done carefully (ask an assistant for help). For greater safety, an assistant should help to push the wheelchair when moving across inclined or
potentially dangerous terrain.
WHEELCHAIR SPEED
Always adjust your speed in relation to the type of terrain and conditions.
As general rule, we advise a constant, regular speed avoidingsuddenaccelerationsorchangesindirection.
BRAKES
The parking brakes have been designed to hold the wheelchairstablewhenitisstationary.
In the interest of safety, you should not use the parking brakes while the wheelchair is in motion.
When using the brakes, great careshouldbetakento avoidinjurytothehandsor fingers.

Exelle Vario Classic 19
3.2 Transfers: getting in and out of the wheelchair
Do not place your feet on the footrest while transferring to or from the wheelchair.
This could cause the wheelchair to tip up, possibly causing damage to the wheelchair and harm to the occupant.
Wheelchair transfers must always be performed with extreme care and caution, even by experienced occupants, and only after receiving instruction from fully trained specialists. If wheelchair transfers are
difficult, an assistant should be lend help.
All these actions should in any case be performed taking account of the degree of your disability and your consequent level of autonomy.
The general rules to respect while getting in or out of the wheelchair safely are:
Ensure the wheelchair is parked on a solid, flat, or regular surface. Do not get in or out of the wheelchair while on hills or uneven ground which could render the wheelchair unstable and cause the
occupant to fall and/or the wheelchair to overbalance.
The parking brakes should be engaged. Remove your feet from the footrest when leaving the wheelchair, and bring them close to the footrest when getting in.
If the wheelchair is equipped with flip-up footrest (single or dual), raise it to facilitate the transfer.
(1) Lean on the wheelchair and, where possible, on a stable object nearby. Use the force of your arms to raise and move your body.
(2) If the occupant is not able to perform this movement alone, or if the movement is to be performed on an uneven surface, an assistant should lend help.
Assistants who help with wheelchair transfers must always observe the upmost care. Such operations must be performed only after receiving instruction from fully trained specialists.
A second assistant should be on hand if particularly risky wheelchair transfers are performed.
In such cases, all the actions should be performed taking account of the occupant’s level of disability.
During wheelchair transfers, never lean or sit on the clothing guard or armrest. These elements could bend or break, possibly resulting in injury.
If your wheelchair is equipped with armrests, remove or swivel the transfer-side armrest outwards or back to facilitate the manoeuvre.
If your wheelchair is a tilting seat type, you should set it flat.

Exelle Vario Classic 20
3.3 Starting to drive your wheelchair
FINDING THE CENTRE OF GRAVITY
Your ability to control and safely tip the wheelchair mainly depends on your seating position and the location of the centre of gravity with respect to the rear wheels.
The correct position of the rear wheels depends on different factors such as the occupant’s weight, type of disability and the occupant’s driving skills.
The manufacturer delivers the wheelchair and the position of the rear wheels (configuration) as requested in the order form.
Finding the point at which the chair will tip back safely requires the presence of an assistant who must stand behind the wheelchair ready
to prevent it from overbalancing.
To find the point at which the chair will tip back easily and, consequently, to find the safe manoeuvring range, proceed as described below.
Starting from your seated wheelchair position:
−firmly grasp the rear wheel rims
-- then move the hand rims slightly backwards and, while moving your weight backwards, push the hand rims forward with a jerk to make the front of the wheelchair rise
−at this point, by moving your body gently backwards and forwards, while moving the rear wheel backwards and forwards using the hand rims, you will be able to locate the centre of gravity and the
different points at which you can achieve controlled tipping and risk dangerous overbalance of the wheelchair.
If you hang a backpack, a bag or any other object on the push handlebars or any rear area of the wheelchair, the resulting uneven weight distribution can significantly
affect the risk of overbalancing.
TO PREVENT THE WHEELCHAIR FROM OVERBALANCING DURING NORMAL USE, WE RECOMMEND FITTING AN ANTITIPPING SYSTEM.