Progress Lighting AirPro P250108 User manual

Ceiling Fan Installation Manual
93166072 P250108 / P250113

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No. 109226
P250108 / P250113
Limited Lifetime Warranty
Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so
long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to
be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic
blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of
any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.
Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are
warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance
with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for
fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical
components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no
warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.
With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for
replacement. After 30 days, the original purchaser MUST contact Progress Lighting at [phone] for repair or replacement
which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.
Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not
limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.
This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or
neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without
limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or
attempted) or failure to provide maintenance to the fan.
THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND
ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS
LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR
CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NONINFRINGEMENT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or
consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights
and you may have other rights which vary from state to state.
UPC
785247257003
785247257010
785247257027

1.
2.
3.
9.
10.
12.
13.
14.
Table of Contents
Safety Rules ..................................................................................................................................................................
Unpacking Your Fan .....................................................................................................................................................
Installing Your Fan .......................................................................................................................................................
Installing the Light Kit and Glass Shade .....................................................................................................................
Operating Your Transmitter ........................................................................................................................................
Care of Your Fan .........................................................................................................................................................
Troubleshooting ..........................................................................................................................................................
Specifications ..............................................................................................................................................................

1. To reduce the risk of electric shock, insure electricity has been turned off at
the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical Code and
local electrical codes. Electrical installation should be performed by a
qualified licensed electrician.
3. WARNING: To reduce the risk of electrical shock and fire, do not use this
fan with any solid-state fan speed control device.
4. WARNING: To reduce the risk of fire, electric shock, or personal injury,
mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35
lbs.) Or Less" and use mounting screws provided with the outlet box.
Most outlet boxes commonly used for the support of light fixtures are not
acceptable for fan support and may need to be replaced. Due to the
complexity of the installation of this fan, a qualified licensed electrician
is strongly recommended.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted and capable
of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use only
UL-listed outlet boxes marked FOR FAN SUPPORT.
6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from
the trailing edge of the blades to the floor.
7. To operate the reverse function on this fan, press the reversing button
while the fan is running.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be cautious
when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades. A dry
dust cloth or lightly dampened cloth will be suitable for most cleaning.
11. After making electrical connections, spliced conductors should be turned
upward and pushed carefully up into the outlet box. The wires should be
spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
12. Electrical diagrams are for reference only. Light kits that are not packed
with the fan must be UL Listed and marked suitable for use with the
model fan you are installing. Switches must be UL General Use Switches.
Refer to the Instructions packaged with the light kits.
NOTE
READ AND SAVE ALL INSTRUCTIONS!
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.
1. Safety Rules

Unpacking Your Fan 2.
15. Loose parts bag containing:
a. Blade attachment hardware
1/4" x 15mm screws with lock washers (19)
b. Mounting hardware
Wire nuts (3)
Unpack your fan and check the contents. You should have the following items:
1. Fan blades (6)
2. Blade support plates (6)
3. Canopy assembly
4. Ball/downrod assembly
5. Collar cover
6. Fan motor assembly
7. Decorative housing
8. 20W LED light kit
9. Glass shade assembly
10. Metal light cover (for no light use)
11. Receiver with 9 wire nuts
12. Transmitter incl. holder + 2 mounting screws
13. 12V MN21/A23 battery
14. Balancing kit
1
2
37
812
13
14 15
9
10
11
4
5
6a
b
I
II
III IV
V
VI

Tools Required
Phillips screw driver, straight slot screw driver,
adjustable wrench, step ladder, and wire cutters.
Mounting Options
If there isn't an existing UL listed mounting box,
then read the following instructions. Disconnect
the power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the
fan (at least 35 lbs). Do not use plastic outlet boxes.
Outlet box
Outlet box Outlet box
NOTE: You may need a longer downrod to maintain
proper blade clearance when installing on a steep,
sloped ceiling.
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4 (available at your
Progress Lighting Retailer).
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR OTHER PERSONAL INJURY,
MOUNT FAN ONLY TO AN OUTLET BOX
MARKED ACCEPTABLE FOR FAN SUPPORT
AND USE THE MOUNTING SCREWS
PROVIDED WITH THE OUTLET BOX. OUTLET
BOXES COMMONLY USED FOR THE
SUPPORT OF LIGHTING FIXTURES MAY NOT
BE ACCEPTABLE FOR FAN SUPPORT AND
MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Angled ceiling
maximum
25 angle
Recessed
outlet box
Provide strong
support
Ceiling
hanger
bracket
3. Installing Your Fan
Figure 1 Figure 3
Figure 4
Figure 2

Step 1.Begin by using the original product
packaging to create a base to hold the fan. Place
the fan motor with the bottom facing up.
Step 2.Remove 1 of the 3 screws from the
mounting ring and loosen the other 2 screws. (Do
not remove)
Step 3.Place the key holes on the decorative
housing over the 2 screws previously loosened
from the mounting ring, turn decorative housing
until it locks in place at the narrow section of the
key holes. Secure by tightening the 2 screws
previously loosened and the one previously
removed. (Fig. 5)
Attaching the Decorative
Housing Attaching the Fan Blades
WARNING: To reduce the risk of personal
injury, do not bend the blades while installing,
balancing the blades, or cleaning the fan.
Step 1. Fasten blade to motor with provided
blade support plates and screws. Make sure
screws are TIGHT! Loose motor screws can
contribute to unnecessary hum or wobble during
operation. (Fig. 6)
Step 2. Repeat these steps for the remaining
blades.
4.
Figura 5
Screw
Screws
Mounting ring
Decorative
housing
Fan motor
assembly
Screws
Blade support
plates
Blades
Figure 6

5.
WARNING
FAILURE TO PROPERLY INSTALL
LOCKING PIN AS NOTED IN STEP 7
COULD RESULT IN FAN LOOSENING AND
POSSIBLY FALLING.
Figure 8
Figure 7
Ceiling
hanger
bracket
Mounting screws
(supplied with
electrical box)
CUL Listed
electrical
box
120V Wires
Washers
REMEMBER to turn off the power. Follow
the steps below to hang your fan properly:
Step 1. Remove the decorative canopy bottom
cover from the canopy by turning the cover
counter clockwise.(Fig. 7)
Step 2. Remove the mounting bracket from
the canopy by removing 1 of 2 screws from
the bottom of the mounting bracket and
loosening the other one a half turn from the
screw head. Next, turn the canopy counter
clockwise to remove the mounting bracket
from the canopy. (Fig. 7)
Step 3. Pass the 120-volt supply wires
through the center hole in the ceiling hanger
bracket as shown in Fig. 8.
Step 4. Secure the hanger bracket to the
ceiling outlet box with the screws and
washers provided with your outlet box.
Step 5. Remove the hanger pin, lock pin and
set screws from the top of the motor
assembly. (Fig. 9)
Step 6. Route the wires exiting from the top
of the fan motor through the collar cover,
canopy cover, canopy and then through the
ball / downrod. (Fig. 9)
Step 7. Align the holes at the bottom of the downrod
with the holes in the collar on top of the motor
housing (Fig. 9). Carefully insert the hanger pin
through the holes in the collar and downrod. Be
careful not to jam the pin against the wiring inside
the downrod. Insert the locking pin through the hole
near the end of the hanger pin until it snaps into its
locked position, as noted in the circle inset of Fig. 7.
Step 8. Tighten two set screws on top of the fan
motor firmly. (Fig. 9)
Step 9. Place the downrod ball into the hanger
bracket socket. (Fig. 10)
Ceiling hanger
bracket
Ceiling
canopy
Canopy
cover Figure 9
Supply wires
Set screws
Collar cover
Canopy cover
Canopy
Canopy cover
Pin in locked
position
Collar cover
Ball/downrod
assembly
Canopy
Lock pin
Lock pin
Hanger pin
Hanger pin
Set screws

6.
Figure 10
Groove Tab
Figure 11
Hanger
bracket
Receiver
Make the Electrical
Connections
WARNING: To avoid possible electrical shock,
be sure electricity is turned off at the main fuse
box before wiring.
WARNING: Check to see that all connections are
tight, including ground, and that no bare wire is
visible at the wire nuts, except for the ground wire.
CAUTION: To reduce the risk of electric shock,
this fan must be installed with an isolating wall
control/switch.
NOTE: The fan must be installed at a maximum
distance of 20 ft. from the remote control for
proper signal transmission between the remote
control and the fan's receiving unit.
If you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Follow the steps below to connect the fan to your
household wiring. Use the plastic wire nuts with
your fan. Secure the plastic wire nuts with
electrical tape. Make sure there are no loose
strands or connections.
Step 1. Insert the receiver into the mounting
bracket with the flat side of the receiver facing
the ceiling. (Fig. 11)
Step 2. Make wire connections from the fan to the
receiver. (Fig. 12)
From Fan To Receiver
White Wire ------------ White Wire "For Light"
Blue Wire -------------- Blue Wire "For Light"
Yellow Wire ----------- Yellow Wire
Red Wire --------------- Red Wire
Grey Wire -------------- Grey Wire
Step 3. Make wire connections from the receiver
to the outlet box. (Fig. 12)
From Receiver To Outlet Box
Black Wire "AC in L" ----- Black Wire (Hot)
White Wire "AC in N"----- White Wire (Neutral)
From Fan & To Outlet Box
Receiver
Green Wires* -------- Green or Bare Wire (Ground)
* There are three green grounding leads: from the
mounting bracket, hanger ball/downrod assembly,
receiver.
Step 4. Turn the wire nut connections upward,
spreading them apart so the green (ground) and
white wires will be on one side of the outlet box
and the black and blue wires will be on the other
side. Carefully tuck the connections up into the
outlet box.

7.
Figure 12
White ("AC IN N")
White (Neutral)
Black ("AC IN L")
Black (Hot)
Receiver
Outlet Box
White
White
Blue
Blue
Red
Red
Yellow
Yellow
Grey
Grey
Green
Green
Green
Ground conductor
Green
Canopy
Figure 13
Outlet box
Hanger
bracket
Canopy
Canopy cover
Screws
Finishing the Installation
Step 1. Tuck connections neatly into ceiling outlet
box.
Step 2. Slide the canopy up to mounting bracket
and place the key hole on the canopy over the
screw on the mounting bracket, turn canopy until it
locks in place at the narrow section of the key
holes. (Fig. 13)
Step 3. Align the circular hole on canopy with the
remaining hole on the mounting bracket, secure by
tightening the two set screws. NOTE: Adjust the
canopy screws as necessary until the canopy and
canopy cover are snug.
WARNING
MAKE SURE THE TAB ON THE HANGING
BRACKET PROPERLY SITS IN THE GROOVE
IN THE HANGER BALL BEFORE ATTACHING
THE CANOPY TO THE BRACKET BY
TURNING THE HOUSING UNTIL IT DROPS
INTO PLACE.