Prolitec AirQ AQ570 User manual

Through Wall
installation instructions
PERFECTLY SCENTED ENVIRONMENTS
Original Instructions
Rev. 2019-01-04

Through Wall Kit 2
Contents
Chapter 1: Tools Required
Chapter 2: Unpacking
Chapter 3: Assembly
Chapter 4: Installation
Positioning the Appliance
Positioning the Plume Outlet
Preparing the Appliance
Connecting the Appliance

Through Wall Kit 3Tools Required
Tools Required
1. Stud nder
2. Drill
3. Phillips #2 bit
4. < 1/2” drill bit
5. Keyhole saw (not pictured)
6. 2 1/8” hole saw
7. Exacto knife (not pictured)
1

Through Wall Kit 4Unpacking
Unpacking
Remove all parts from the container. The following items should be included:
1. AQ570/580 Appliance (not pictured)
2. 110/220V to 15V Power Adapter (not
pictured)
3. Universal Plug Kit (not pictured)
4. Wall Mount Hardware Kit (not pictured)
5. Through Wall Fitting Parts (in bag)
a. Base Housing
b. Trim Ring
c. Drywall Clips (2)
d. 1 ¼” Screws (2)
e. 3” Screws (2) (not pictured)
f. Fan w/ 18” black and red wires
g. Tube Connector
h. Wire Connectors (2)
6. Tubing (18”)
7. Braided Cord Wrap (18”)
5a
5b
5c
5d
5f
5g
5h
7
6
2

Through Wall Kit 5Assembly
Assembly
1. Press t the fan into the base housing part by aligning the three corner holes to the three
hexagonal posts.
2. Insert the correct length screw (dependent on installation type) into the holes on the front of
the base housing part, thread the drywall clips onto each screw, and tighten screws three or four
turns.
a. 1 ¼” screws should be used on drywall/gypsum board
b. 3” screws should be used on doors
3

Through Wall Kit 6Assembly
3. Push one end of the tubing onto the tting on the back side of the base housing part, just below
the fan tray, and rotate the clips in toward the fan on both sides.
4. Wrap the wire around the tubing.
5. Slide the cord management sleeve over the tube and wire.
3

Through Wall Kit 7Installation
Installation
Positioning the appliance in the “appliance mounting room”
1. Identify the area on the opposite side of the wall from the approximate mounting location.
2. Verify that you have an area of empty wall cavity, using a stud nder.
3. Cut a 6” x 6” square hole with a keyhole saw, so that you can verify that there is not electrical or
plumbing in the way and so that you can get the drill inside the wall cavity.
4. Working from within the 6” square, drill a pilot hole through the front wall surface, with the ½”
drill bit.
5. Mount the appliance on the wall normally, with the top of the appliance six to eight inches below
the bottom of the 6” square hole.
4

Through Wall Kit 8Installation
Positioning the plume outlet in the room to be scented
1. Drill a 2 1/8” hole, centered on the pilot hole, with the hole saw.
2. Insert the base housing, with the fan, clips, and tube already attached, into the hole.
3. Screw in the two screws until you feel the plastic snug towards the drywall.
4

Through Wall Kit 9Installation
4. Snap the trim ring over the front to hide the screws.
Preparing the Appliance
1. Remove fan shroud 2. Remove fan
3. Cut fan wires at the fan
!
4

Through Wall Kit 10Installation
Connecting the appliance in the “appliance mounting room”
1. Connect the wires of the fan assembly to the wires from the appliance, red to red and black to bl
2. Bundle the wires and tube inside of the sleeve.
3. Install the cartridge with the top plume port open.
4. Insert the plume tube into the top plume port of the cartridge.
4