Prolitec Air-Q 1100 User manual

Page1of18
Air‐Q1100
UserGuide

Rev1.05/13/09

©2009,ProlitecInc.

Air-Q 1100 User Guide Page2of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
Air‐Q1100
UserGuide
(Rev1.05/13/09)

©2009ProlitecInc.

I.IntroductiontoAir‐Q1100............................................................................... 1
A.ApplicationsandUses
1.AmbientScenting
2.OdorControl

II.SafetyPrecautions........................................................................................... 3
A.AppliancePrecautions
B.FragrancePrecautions

III.ApplianceandControls ................................................................................... 4

IV.GeneralMaintenance....................................................................................... 5
A.ChangingtheCartridge
B.O‐ringreplacement
C.BatteryReplacement

V.CommissioningAir‐Q1100.............................................................................. 7
A.UnitProgramming
B.SettingScentIntensity


VI.Installation........................................................................................................ 9
A.Pre‐InstallationChecklist
B.InstallationKit
C.AppliancePositioning
D.ApplianceInstallation
E.InjectorTubeInstallation

VII.Troubleshooting ............................................................................................. 15

VIII.GeneralCareandCustomerSupportContacts............................................ 17

IX.Specifications.................................................................................................. 18

Page1of18
I.IntroductiontoAir‐Q1100

TheAir‐Q1100applianceisanairtreatmentsystemforinteriorspacesservedbyaductedHVACair
handlingsystem(“HVAC”).TheAir‐Q1100deliversafragranceorairtreatmentagent(“Agents”)
intotheairflowoftheHVACsystemeitherthroughthecentralfanunit(CFU)oratsuitable
locationsinthebranchedductwork.Itisdesignedforpermanentinstallationontheoutsideor
insideoftheCFU.

TheAir‐Q1100ismanagedbyanon‐boardcomputerthatisfullyprogrammableforspacesizes
from1,000to250,000cubicfeetperapplianceandoneormoreintensitylevelsinthesameday.
MultipleappliancescanworktogetheronthesameormultipleCFUstotreattheairinthesame
spacesservedbytheHVAC.Inthisway,thereisnolimitationonthesizeofthespacethatcanbe
servedbyAir‐Q1100.

Air‐Q1100requireslittletonomaintenanceexceptperiodiccleaningforappearance.Installations
ofAir‐Q1100aredesignedsothattheconsumptionoftheconsumableCartridgesofAgent
(“Cartridges”)requiresreplacementnomorefrequentlythanonceamonth.

TypicalAir‐Q1100applicationsincludeairtreatmentforodorremediation,scentbrandingand
ambientscentinginpublicspacessuchascasinos,malls,hotels,theaters,ballrooms,convention
centers,hospitals,andrestrooms.

TheAir‐Q1100generatesultrafine,ultra‐lightdropletsapproximately500nanometersin
diameter.Bycomparison,adropletfromapressurizedaerosolis50microns(50000nanometers)in
diameteror166timeslargerthananAir‐Q1100droplet.Intermsofweightandvolumeofliquid,
thecomparisonisevenmoredramatic.A50‐micronaerosoldropletis4.6milliontimesheavier
thana300‐nanometerAir‐Qdroplet.1ThistinyAir‐Qdropletoffersmanyperformancebenefits
overaconventionalaerosolincluding:completelyuniformdistributionofthetreatmentagent;100
timesmoreexposedsurfaceareaallowinguseofmuchlessairtreatmentagentpercubicfoot;and
theabsenceofanyliquiddepositsonsurfacessuchastheinteriorsurfacesinaHVACsystem.

TheAir‐Q1100Guideispackedwithimportantinformationthatwillhelptheusers,installersand
serviceengineersoptimizetheperformanceofthismodernairtreatmentsystem.Weencourage
youtoreaditcarefully.

1This is calculated using the formula for the volume of a sphere where Vis the volume or weight and r is
the radius of the droplet.

Air-Q 1100 User Guide Page2of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
A. ApplicationsandUses:

Air‐Q1100isusedwithproprietaryfragrancesandodorremediationagents(“Agents”)toenhance
indoorairqualitybyerasingodorsandintroducingscent.Thisisaccomplishedbyconvertingliquid‐
stateAgentsintoultra‐finedropletsandinjectingthemintothemintotheHVACsystemtoblend
withtheairflow.Usedasdirected,theconcentrationofAgentintheairwillusuallybelessthan1
partpermillion(<1ppm).Thismeansthatforevery1,000,000moleculesofair,lessthan1
moleculeisairtreatmentAgent.TheAir‐Q1100’sdropletsareabout500nanometersindiameter
(halfamicron).Adropletofthissizepresents10,000timesmoresurfaceareatotheairthanthe
sameamountofliquidina50‐micronaerosoldroplet.TheAir‐Qdropletis1/1,000,000ththeweight
ofanaerosoldroplet.Thismeansthedropletsbehaveasiftheyweredry,donotleaveanyresidue
onthebladesorinteriorductsurfacesandcreatescenteffectwithconcentrationssolowitus
unlikelytotriggerallergicresponse.

TherearetwobasicapplicationsforAir‐Q1100:ambientscentingandodorremediation.TheAir‐Q
1100deliverysystemandProlitec’sproprietaryairtreatmentchemistrycandobothatthesame
timeoreitheronealone.

1.AmbientScenting
AmbientScentingistheuseoftheAir‐Q1100todeliverascenttocreateamoodor
ambience,associateascentwithabrand,enhanceavisualthemeorsimplymakeaspace
morepleasantforitsoccupants.

2.OdorControl
OdorControlistheuseofAir‐Q1100andspecialairtreatmentchemistrytoneutralize
odorsbyblockingcertainmalodorsthusallowingtheintroductionofverysmallquantities
offragranceintotheair.Normalairfreshenerssimplyusefragrancetodouseamalodor.


Air-Q 1100 User Guide Page3of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
II.SafetyPrecautions

A.Air‐Q1100AppliancePrecautions:

• Theappliancemustbeoperatedinanuprightorverticalpositionandfirmlyattachedtoa
verticalsurfacesuchasawalloraduct.

• TheapplianceshouldNOTbeusedwiththedoorintheopenposition.Thedoorisopened
onlytoperformacartridgeorprogramchange.

• NEVERputyournosetotheoutputofAir‐Q.Within12inchesoftheoutput,thefragranceis
highlyconcentrated.Theimproperinhalationofhighconcentrationsoffragrancemaycause
irritationincludingwateryeyes,headache,coughandupperrespiratorydiscomfort.

• Theapplianceisbuilttobepluggedintoan110VACor220VACpoweroutlet.TheULandCE
compliantpowersupplyconvertspowerto12VDCtopowertheappliance.

• Unplugbeforecleaning.


B.Air‐QCartridgePrecautions 

• ReadtheProductSafetyInformationSheetandtheMaterialSafetyDataSheetenclosed
providedwitheachshipmentofCartridges.Insurethattheseinformationsheetsare
availableforreviewbyemployees

• UselatexglovestohandleaCartridgetoavoidtheliquidgettingonhands.TheAgentsare
formulatedsoastonotbeharmfulincontactwiththeskin,buttheconcentratednatureof
theagentsmakesthescentdifficulttoremovefromhandsandskin.

• WashyourhandsafterallcontactwithCartridgesorfragranceandairtreatmentagents.

• CartridgesmustbeprovidedbyandcontainAirTreatmentAgentformulationswhichhave
beencertifiedbyProlitec.

• WhileAir‐QAirTreatmentAgentsdonotcontainingredientsdeemedharmfultotheskin,if
thereisskincontact,washwithsoapandwater.Ifthereiscontactwiththeeyes,irrigate
theeyewithfreshwaterfor5minutes.Ifthereisanyeyeirritation,consultaphysician
immediately.

Air-Q 1100 User Guide Page4of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
III.ApplianceandControls


Air‐Q1100
























Cartridge
InjectorHose
ControlDisplay
ControlButtons
PowerCord
ProgramSelector
BatteryTab
AirNozzle
HoseConnector
HoseClamp
AirFilter

Air-Q 1100 User Guide Page5of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
IV.GeneralMaintenance

A.ChangingtheCartridge
• Unlatchandopenthedoortoaccessthecartridge:Thedoorshouldbeopenedonlyto
performacartridgeorprogrammingchange.Wheninuse,thedoormustbeclosed.
1.Removeairnozzle(locatedonthesideofthecartridgehead)byrotating90degreesand
pullingtowardsyou.(SeePicture#1)
2.DetachInjectorhoseandhoseconnectorfromthecartridgeoutputport(locatedonthe
topofthecartridgehead).Thisisdonebyunscrewingthehoseconnectorfromthe
cartridgeoutputportandpullingout.
3.Removecartridgefromapplianceenclosure.
4.Installnewcartridge,placeandtightenhoseconnectorfirmlyoncartridgeoutputport.
5.Insertairnozzleandrotatethehandle90degreesuntilsecured(bystemretainingtab
oncartridgehead).(SeePicture#2)
6.Turnapplianceon.Verifythattheplumeisnotescapinginsidetheapplianceandthatall
connectionsaretight.Closethedoorwhencomplete.











B.O‐ringReplacement–every6monthsorasneeded:
• Replacetheairnozzle3o‐rings(Partnumber10208) ifworedownorswollen.Apartiallyfull
cartridgemayindicateanairleakbetweentheairnozzleandthecartridge,reducingplume
output.Replaceasneededand/oreverysixmonthsforpreventativemaintenance.
• IfthereisanyAgentthatleaksduringthecartridgeinstallation,cleanitcarefullywitha
papertowelwithsomeethanoloranotheralcohol.

C.AirFilter–every6monthsorasneeded.
• Replaceairfilter(partnumber10417) ifdirty.Ifanydusthasgatheredinsidetheunit,
removeitwithadamppapertowel.
Picture1Picture2
Cartridge
RetainingTab

Air-Q 1100 User Guide Page6of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc

D.BatteryReplacement–approx.every2years:
(requires3VoltCR2032LithiumBattery,partnumber8111):
1.Unlatchandopenthedoortoaccesstheenclosure.
2.Usingapairoftweezersorneedle‐nosepliers,remove
batteryfromthecenteropeningoftheovalgrommet.The
grommetislocatedonthefrontofthebluebracketbelowthe
operatingbuttons.
3.InsertthenewCR2032battery.Thepositivesideofthe
batteryshouldfaceyourrightwhilelookingatthefrontofthe
appliance.Thebatterywillhavea+or–markingonaside.

Air-Q 1100 User Guide Page7of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
V.CommissioningtheAir‐Q1100

A‐UnitProgramming

1.Openthedoorandunlockifneeded.

2.TurnonthepowerbypressingtheON/OFFbuttonintheupperleftcornerofthecontrolpanel.
(MakesuretheapplianceispluggedintotheACpoweroutlet.)Thepowerbuttonwilllightblue

3. SettingtheClock.

•TurnthedialtoSetClock.Thetimewillblink.

•Adjustthetimeforwardorbackwardusingthe+/–buttonsontherightsideofthecontrol
panel.AMorPMisindicatedonthelowerrightsideofthetimedigits.Hold+tofastforward.

4. Usingthe24/7Mode.

• IfyouwanttheAir/Q™1100toruncontinuously—7daysaweek,24hoursaday—turn
thedialto24/7.Ifnot,skiptoStep5.

5. SettingspecificStart/StopTimes.

• TurnthedialtoStart.

• Adjusttheclocktothetimeyouwanttheappliancetostarteachdayusingthe+/–keys.

• TurnthedialtoStop.

• Adjusttheclocktothetimeyouwanttheappliancetostopeachdayusingthe+/–keys.

6. UsingtheProgramMode

• TurnthedialtoProgramtooperatewiththespecifiedstart/stoptimes.

7. UsingtheProgramOverride

• Pressthebuttoninthebottomleftcornertooperatetheapplianceoutsidethespecified
start/stoptimes.

• Eachtimethebuttonispressed,anotherhourisaddedupto12hours.




Air-Q 1100 User Guide Page8of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
B‐SettingScentIntensity
1.ConsulttheSettingsTable,whichprovidesasettingforthesizeincubicfeet(lengthxwidthx
ceilingheight)ofthespaceyouaretreating.Usetheindicatedintensitysettingasastarting
pointfromwhichyoucanincreaseordecreasetotaste.Numberoffreshairchangesperhour
anduserpreferencewillaffectsettings.

SettingsTable:

Output Level Range
Settings Space to be treated in Cubic Feet Space to be treated in Cubic Meters
1 thru 5 3,000-15,000 85-425
6 thru 10 15,000-29,000 425-820
11 thru 15 29,000-48,000 820-1360
16 thru 20 48,000-68,000 1360-1,900
21 thru 25 68,000-91,000 1,900-2,600
26 thru 30 91,000-117,000 2,600-3,300
31 thru 35 117,000-146,000 3,300-4,100
36 thru 40 146,000-177,000 4,100-5,000
41thru 45 177,000-214,000 5,000-6,000
46 thru 50 214,000-250,000 6,000-7,100

2. Pressthepowerbuttonon.TurnthedialtoProgramandsettheintensitylevelwiththe+/–
keys.Youwillseethelevelnumbers(1to50)ontherightsideofthescreen.

Hint:Therearemanyvariablesinvolvedinfindingtherightsettingsforscent.Feelfreetoadjustto
taste.DonotsetscentleveltomaximumsettingorhigherthanrecommendedintheSettingTable,
butstartfromrecommendedlowestlevelandincreaseprogressivelyforoptimumresults.

TheLastStep

1.Setthedialtoeither24/7orProgramifyouhaveprogrammedastart/stoptime.

2. Makesurethepowerison.Thebluelightwillshowthroughthebutton.

3. Closeandlockthedoor,storingthekeyinaknownplace.

Air-Q 1100 User Guide Page9of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
VI.Installation

A.Pre‐installationChecklist
Thischecklistshouldbecompletedbeforetheinstalldate.
1.Confirmtheareatobetargetedforairtreatment
2.DeterminetheAirHandlingUnitorductthatservesthetargetarea.
3.MakesuretheAHUdoesnotuseanopengasflame.
4.FindandmarktheoptimalinsertionpointfortheInjectorTube.(SeesectionC:“Appliance
Positioning”)
5.Findandmarktheexactlocationforplacementoftheappliance(SeesectionC:“Appliance
Positioning”)
6.Notethedistancebetweentheinsertionpointandtheproposedappliancelocation.(NEVER
MORETHAN6FEET)andthereshouldNEVERbeaLOWPOINTinthehoserun.
7.Determineandmarkthelocationforthe110or220VACpoweroutlet.(NEVERDIRECTLY
BELOWTHEappliance)

B.InstallationKit(photos–Page10)
• One(1)Air‐Q1100appliance(notpictured)
• One(1)ProlitecInjectorTube(a)
• Three(3)Feet3/8thID,½ODInjectorhose(b)
• One(1)hoseconnectorassembly(c)
• One(1)hoseclamp(d)
• Seven(7)#10self‐tappingsheetmetalscrewsforsecuringtheapplianceandinjectortubeon
sheetmetal.(e)
• 1sparesetof3o‐ringsfortheairthenozzle(f)

Air-Q 1100 User Guide Page10of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
• Optional:Onehosequickdisconnectfittingwith3feethoseextensionwithhoseclamps,to
increasedistanceupto6feet(seenote#6above)

(a)
(b)
(c) (d)
(e)
(f)

Air-Q 1100 User Guide Page11of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
C.AppliancePositioning
Itisimportanttofindaninsertionpointwheretheplumeoutputwillbesmoothlydrawninto
andmixedwiththeairflow.ThisusuallymeansthosepartsoftheAHUwherethestatic
pressureisnegative.Ideallocationsinclude:
• BeforethesupplyfanwithinjectionthroughthewalloftheAHU.Positioningimmediately
beforethefanandafterthecoilsifpossibleorinthemixedairchamber.
• BehindtheblowerwiththewholeappliancemountedinsidetheAHUinthemixedair
chamber.
• OutsidetheAHUintheSupplyairduct.

BestpracticewheninstallinginanAHUistoplacetheinjectortubeaftertheheatingand
coolingcoils.Ifthisisnotpossible,thePlumeoutputcanpassoverhotwater,steam,chilled
water,andDXcoils.

Opengasflamesshouldabsolutelybeavoided.Ifinstallationmustbeovergasheatedcoilsor
opengasflames,contactProlitecTechnicalSupport.

ThebestlocationfortheApplianceisbelowtheinjectortube(SeeFigure1).Theinjectorhose
shouldberunupwardasshortadistanceaspossibleandNEVERMORETHAN6FEETOR180
CENTIMETERS.Ifanupwardinjectorhoserunisnotpossible,careshouldbetakensupportthe
hosetopreventsaggingoranylowspotintheruntoavoidanypossibilityofcondensationand
liquidcollectionwhichwillblocktheplumeoutput.Theinjectorhoseispronetostretching,so
supportpointsshouldbeplacedevery5to6inchesonhorizontalruns.Givethehoseaslight
upwardslantalongitsrun(SeeFigure2).Thehosemustnotberunhorizontally.Astrongtape
(suchasVenturetape)maybeusedtosupportshortruns.ThehosemayberunthroughPVC
pipeforlongerdistances.


Figure1
InjectorTube
PowerJunctionbox
Injectorhose
Air‐Q1100

Air-Q 1100 User Guide Page12of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc















D.ApplianceInstallation

1.TheAPPLIANCEiswall‐mounted.PlacetheAPPLIANCEontothedesiredlocationonthewall
orAHUandensurethatitislevel.
2.FastentheAPPLIANCEtothewallorAHUusingthenecessaryscrews.
3.ConnectthepowercordtoajunctionboxorattachanACplugtothecordandconnecttoa
nearbyoutlet.
4.Opentheenclosuredoorandunscrewthealuminumcapofthewaterproofcollarlocated
ontopoftheapplianceenclosure.Removeandsetasidethegrommet(seephotoonPage
13).
5.Assemblehoseandhoseconnectortogether(seephotobelow).Besuretoleave
approximately1/8ofaninchclearancebetweenthetopofthecartridgehoseconnector
andtheendofthehose.Thensecurewithclamp,ensuringthatthehoseconnectorisstill
freetorotate.




AQ
1100
DUCT or
PLENUM
DIP
INCORRECT
AQ
1100
DUCT or
PLENUM
CORRECT
Figure 2
Clamp
Leave 1/8"
clearance
Hose
Connecto
r

Air-Q 1100 User Guide Page13of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
6.Fromtheinsideoftheenclosure,slidehoseassemblyupwardthroughtothewaterproof
collar.

7.LubetheinsideofthegrommetifneededtoallowtheInjectorhosetoeasilyslidethrough.
Leaveapproximately2inchesofhoselengthinsidetheappliancetoprovideenoughplay
whenreplacingthecartridge.Tightenaluminumcapofwaterproofcollartoensurea
watertightseal.
8.Usetheoptionalquickdisconnectfitting(SeephotoonPage10)toaddahoseextensionif
needed.

Waterproof
Colla
r

Air-Q 1100 User Guide Page14of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
E.InjectorTubeInstallation

TheinjectortubeisinstalleddirectlyintotheAHUortheductwork.Itsorientationcanbeadjusted
relativetotheairflow.
• Forinstallationsintothenegative/suctionsideoftheAHUfan,orientthetubewiththe
elbowpointedupwards(SeeFigure2),sothatanyplumecondensationwillsipbackin
thetube.
• Forinstallationsafterthesupplyfan,suchasinasupplyduct,itisnecessarytoconfigure
andorienttheInjectorTubetoobtainagoodaspirationoftheoutputintotheair
stream.Theinjectortubeshouldbepointedinthedirectionoftheairflowandinclined
45oupwardapproximately.Turbulenceintheairflowcanpreventevenaspirationofthe
plume.Itisbesttoplacethetubeinastraightsectionofduct,andfarawayfromany
turns,branches,orcross‐sectionchangesaspractical,andnotimmediatelyafterthe
supplyfan.
1.Attheinsertionpoint,drillaholeusinga½”drillbit.
2.InserttheInjectorTubethroughthehole.
3.FindanorientationoftheinjectorTubethatappearstoproduceagooddrawofairinto
theendofthebarb.
4.Fastentheflangeusingthethree#10sheetmetalscrews
5.TurntheAPPLIANCEonandverifythataplumeisproduced.
6.BeforeattachingtheInjectorhosetotheinjector,verifythattheplumecanfloweasily
throughtheinjector.Thiscanbedonebyplacingtheendofthehose½inchawayfrom
theinjectorandverifyingthattheplumeisbeingdrawnin(aflashlightwillmakethe
plumeeasiertosee).Iftheplumedoesnotriseintothehose,adjusttheorientationof
theInjectorTubeuntilaspirationisachieved.
7.AttachtheInjectorhoseontothehosebarboftheInjectorTube.


ForCartridgeInstallation–See"ChangingtheCartridge"onPage5.

Air-Q 1100 User Guide Page15of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
VII.Troubleshooting

ConditionCausesSolutions
Powerlightoff.TheApplianceisnot
pluggedinortheplug
hasnopower
Makesurethepowerconnectionisoperational.

Verifythatthepowerbuttonlightisbluewhen
pressed.
Unitdoesnotstart
automaticallyafterapower
interruption
Back‐upbatterynot
operational
Verifytheprotectiveyellowbatterytabhas
beenremoved.

Verifythebatteryispositionedwiththepositive
sidefacingtheright.

Replacetheback‐upbattery.
Thefragrancecannotbe
detectedwhencominginto
thetreatedareafroman
untreatedarea.
Theoutputrateistoo
loworthereisan
insufficientnumberof
appliancesservingthe
space

TheO‐Ringsonthestem
thatfitsintothehead
maybewornoutand
causinganairleak.
Increasetheoutputratebyoneortwosettings
andevaluatedetectionin30minutes.Repeatas
needed.IfconsumptionrequiresCartridge
changemorefrequentlythaneachmonth,
installanadditionalappliance.

ReplacetheO‐Ringsbyremovingthewornone
withapointytoolandrollingonthenewones

Fragranceintensityis
strongerthanjust
detectable.
Theoutputrateistoo
high.
Lowertheoutputrateinincrementsofoneor
twosettingsordowntothestartingrates
suggestedintheroomsizechart.
Thepowerlightisonbut
thethereisnooutputor
youcannothearthe
compressorinthe
appliance.
Youareinan“OFF”
periodintheTimercycle.
Simplywaitafewminutesfortheapplianceto
cycleon.Iftherealproblemisthatthescent
cannotbedetected,increasetheoutputrateas
instructedabove.
Thepowerlightisonand
thecompressorcanbe
heardbutnofragrance
detected.
Theoutputtubemaybe
blocked.








Theairintakemaybe
blocked.







Removethehosefromtheoutputtubeleaving
theCartridgeinplaceintheappliance.Turnthe
applianceonsoyoucanhearthecompressor.
Useaflashlighttoobservethetopoftheoutput
headforaplumeofdroplets.Ifyoucanseethe
plumethentheblockagemaybeinthehoseor
theinjectortubeintotheHVAC.Checkthese.If
thereisnoplumesomethingisblockingthe
outputtube.Checkandremoveit.

Anothermethodforclearingobstructionsis,
whiletheappliancecompressorisrunning,
blocktheoutputtubewithafingerfor2or3
secondsandthenopenit.Byremovingyour
finger.





Air-Q 1100 User Guide Page16of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
TheO‐Ringsonthestem
thatfitsintothehead
maybewornoutand
causinganairleak
ReplacetheO‐Ringsbyremovingthewornone
withapointytoolandrollingonthenewones

Youdetectthefragrance
whenenteringtheroombut
afterawhileyounolonger
noticeit.
Thisiscalledolfactory
adaptationandis
normal.
Leavetheareafor5to10minutes.Comeback
inside,youwillsmellthefragranceonceagain.
Donothesitatetorepeatthisprocessevery
timethatyoudoubtthepresenceofthe
fragranceinthearea.

Air-Q 1100 User Guide Page17of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
VIII.GeneralCareandCustomerSupportContacts

• DonotinstallorstoreAir‐Q1100inplaceswheretheambienttemperaturemayfallbelow
0degreesCelsius(32degreesFahrenheit)orriseabove54degreesCelsius(130degrees
Fahrenheit).(Ifoperatingconditionsmustbeoutsidetheseranges,contactProlitecSafety
andSupportHotlineat888.615.9282).
• DonotdropAir‐Q1100onthefloor.Donotdropitinorpositionitnearanopenbasinof
water.
• Donotpaintorotherwisetrytoalterthecoloroftheoutercover.
• AlwayskeepthelidsonCartridgeswhenstoredoutsideoftheAir‐Q1100.
• DonotoperateAir‐Q1100inverydustyareasthatmaycausetheairintaketoclog.
• PleasecallProlitecCustomerServiceat866.387.4333forinstructionsonreturnshipping
instructionsorquestions.







Air-Q 1100 User Guide Page18of18
(rev 1.0 5/13/09)
© Copyright 2009 Prolitec Inc
IX.Specifications

TechnicalCharacteristics  
ReferenceAir‐Q1100:ModelAQ1100
Type1headnebulizerintegratedwithcartridge
Diameterofparticles300nmto1µmicron

PowerInput  
Input100–240VACat0.6A
Frequency50/60Hz
ProtectionSwitchingpowersupply
InternalPower12VDCat1.5A
Back‐upbattery
Lithium3V,#CR2032

Performance  
Upto250,000cu.feet(7,080cumeters)subjecttoairflowconditions

Control
Programmablestart&stoptimes
Programmableoutput0to50


Dimensions  
HeightXWidthXDepth151/2”X133/8”X66/8”(39.4cmX34.0cmX17.2cm)
Weightwithfullcontainer13.7lb(6.2kg)

Cartridge  
Reservoir‐1250ml
Disposable/Recyclable

PatentedProlitecInc.......... Multiplepatentspending

