promesstec WTR 420 Series User manual

promesstec GmbH * Niedersachsenstraße 4 * 48465 Schüttorf * Tel.: [phone] * Fax [phone] * E-Mail: [email protected] * Internet: www.promesstec.com
page 1/4
user manual resistance thermometers
type WTR 420.., WTR 430...
temperature measurement
safety instructions !!!
intended use of the product
- The sensor has been designed exclusively for the intended use described here or in the
datasheet and may only be used in this way.
- The technical specifications contained in these operating instructions must be observed.
- Improper handling or operation of the device outside of its technical specifications
requires the device to be taken out of service immediately and an inspection by
promesstec.
- When the device is transported from a cold into a warm environment, the formation
of condensation may result in the device malfunctioning.
- Before putting it back into operation, wait for the device temperature and the room
temperature to equalise.
The manufacturer shall not be liable for claims of any type based on operation contrary
to the intended use!!
staff qualification
Improper handling can result in considerable personal injury and damage to equipment.
The activities described in these operating instructions may only be carried out by skilled
staff who have the appropriate qualifications. For installation and starting of the sensor,
the relevant regulations and directives of the country and the norms must be observed.
Especially during installation of the sensor, it is possible, depending on the use, to come
into contact with aggressive media. The safety instructions must be observed. There will
be danger to life if live parts are touched. Electrical installation and commissioning may
only be carried out by qualified and skilled personnel.
special hazards
Residual media in dismantled devices can result in a risk to personnel, the environment
and equipment. Sufficient precautionary measures must be taken here. Do not use the
instruments in safety or emergency stop devices. Incorrect application or operation of the
instrument can lead to injuries. Depending on the application, aggressive media with
extreme temperatures and high pressure or vacuum may be present at the instrument in
the event of a fault. We recommend installing and removing the device only at ambient
temperature and in a pressureless mode.
hazards when operating the device
Our devices have a very high protection class when properly mounted and installed. When
cleaning your system with high-pressure cleaners, steam cleaners etc., make sure that
both the cover and the cable screw or M12 connector are not directly exposed to the
pressure jet. If the temperature falls below the dew point, condensation may form in the
connection chamber of the device. In such extreme applications, contact our sales and
technical support before commissioning.

1 4
2 3
1 4
2 3
21
3
1
3
2
temperature measurement
connection WTR 420
mechanical structure WTR 420...
electrical connection WTR 420 without measuring transducer PMU
1 (brown)
2 (white)
3 (blue)
4 (black)
M12 plug
PT100 and PT1000
ISO 4400 plug
PT100 and PT1000
electrical connection WTR 420 with measuring transducer PMU
1 (brown)
voltage
10...35VDC
3 (blue)
output 4...20mA
M12 plug with PMU
The optional measuring transducer PMU can be set with the software PXU01 and the
corresponding programming adapter. The user manual for the software is included in the
programming kit.
page 2/4
promesstec GmbH * Niedersachsenstraße 4 * 48465 Schüttorf * Tel.: [phone] * Fax [phone] * E-Mail: [email protected] * Internet: www.promesstec.com
M12 plug
2x PT100 or 2x PT1000
1 4
2 3

1 4
2 3
1 4
2 3
The optional measuring transducer PMU can be set with the software PXU01 and the
corresponding programming adapter. The user manual for the software is included in the
programming kit.
M12 plug with PMU
3 (blue)
output 4...20mA
1 (brown)
voltage
10...35VDC
page 3/4
promesstec GmbH * Niedersachsenstraße 4 * 48465 Schüttorf * Tel.: [phone] * Fax [phone] * E-Mail: [email protected] * Internet: www.promesstec.com
electrical connection WTR 430 with measuring transducer PMU
M12 plug
PT100 and PT1000
1 (brown)
2 (white)
3 (blue)
4 (black)
electrical connection WTR 430 without measuring transducer PMU
mechanical structure WTR 430...
connection WTR 430
temperature measurement
1 4
2 3
M12 plug
2x PT100 or 2x PT1000

mechanical installation
return and repair
electrical mounting
- Only use promesstec welding sleeves and process connections for adaptation to your
process. This is the only way we can guarantee you clean and aseptic measuring point.
- After installing the sensor, check the tightness of the measuing point.
The promesstec sensor have a modular design. This allows us to repair and
overhaul defective devices. To do this, send the device to promesstec. You will find a
return form with the information to be provided on our homepage under
„technical information“.
disposal of the device
promesstec GmbH * Niedersachsenstraße 4 * 48465 Schüttorf * Tel.: [phone] * Fax [phone] * E-Mail: [email protected] * Internet: www.promesstec.com
Dispose of devices, components and packaging in an environmentally friendly manner
in accordance with the waste treatment and disposal regulations typical for the country.
Pay attention to waste separation and the recycling of high-quality materials such as
stainless steel, etc.
further documentation
These operating manual and the datasheets can be found as a file on our homepage
under the respective devices. The documetation is available in German as well as in
English. Other languages are available on request. Additional information such as
characteristic curves of temperature sensors etc. can be found on our homepage under
important information !!!
mounting instructions !!!
temperature measurement
version 2.1.3 page 4/4
- Install the sensor in your process before the electrical mounting. In this way, you prevent
coiling of the cable when mounting the meauring point.
- M12 plug: Turn the M12 socket by hand onto the plug on the promesstec sensor.
The mounting is done without tools.
- When mouting the connection cable, ensure that both components are firmly and positively
connected. For the permissible tightening torque, refer to the datasheet of the respective
connection cable.
- SO 4400 plug: Connect the ISO4400 plug electrically. Ensure a positive connection
between the screw connection and the cable. Plug the connector onto the sensor.
Secure the plug by the screw in the head. Check the fit of the sealing and the tightness
of the connection.