ProMinent mikro g/5a User manual

Page 1
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
ProMinent®
Table of contents Page
EC Conformity Declaration 2
1. Operating the pump 4
1.1 Sectional drawing and legend 4
1.2 Explanation of symbols on pump front panel 5
2. Safety instructions 5
3. Mechanical construction and function 6
3.1 Description of function and operation 6
3.2 Connection and initial operation 7
3.3 Operating conditions and directions for use 8
3.4 Minor faults, causes and remedies 9
3.5 Installing the liquid end / feeding end plunger packing 12
3.6 Installing liquid end / feeding end Bal Seal 14
3.7 Installing axial plunger sealing Bal Seal and plunger 15
4. Technical data sheets 16
4.1 Determining the feed capacity 16
4.2 Nomograms 17
4.3 Performance data 19
4.4 Electrical data and Enclosure rating 19
4.5 Pump specific data 20
Appendix:
Instruction manual “ProMinent®gamma/ 5a”
Brochure with measuring sheet “ProMinent®mikro g/5a”
Instruction Manual
ProMinent®mikro g/5a Precision feeding pump
DIN EN ISO 9001
70 100 M 502
Part No. 987909 ProMinent Dosiertechnik GmbH ·Im Schuhmachergewann 5-11 ·D-69123 Heidelberg BA M5 003 10/97 GB

Page 2
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a

Page 3
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
MG5A
Series:
MG5a = mikro g/5
Version a
Pump size: Section 4
1st and 2nd figure =
Backpressure (bar)
3rd to 6th figure =
Capacity (ml/h)
400150
180600
061500
Material TT....
max. 10 bar backpressure
Material: Section 4
SS 1= Stainless steel mate-
rial No. 1.4571, with
PTFE packing, pure
white
SS 2= Stainless steel mate-
rial No. 1.4571 with
PTFE packing, gra-
phite
SS 3 = Stainless steel with
Bal-Seal seal
TT 1= PTFE + 25 % carbon
with PTFE packing,
pure white
TT 2= PTFE + 25 % carbon
with PTFE packing,
graphite
TT 3= PTFE + 25 % carbon
with Bal-Seal seal
Control type:
1 = Option type
2 = Option type with LCD
lighting
Control variant:
0 = Manual + external + pause
1 = As 0 + Analog
0...20 mA, 4...20 mA
2 = As 0 + Analog
0 - 60 mV, 0 - 1 V, 0 - 10 V
= Special version
---------------------
Electrical connection:
power cable 2 m long
A = 230 V ±10 % 50/60 Hz
Euro plug
B = 230 V ±10 % 50/60 Hz
Swiss plug
C = 230 V ±10 % 50/60 Hz
Australian plug
D = 115 V ±10 % 50/60 Hz
USA plug
= Special version
---------------------
Transparent cover
version:
0 = Standard
1 = With lock
Valve spring:
0 = No spring
1 = With 2 valve
springs
1.4571 0,1 bar
Pulse control:
0 = Without pulse control
1 = With pulse control
Timer:
Separate operating instructions
0 = Without timer
1 = With timer
Relay switching mode:
0 = No relay
1 = Fault indicating relay, releasing
2 = Pacing relay, operating
3 = Fault indicating relay, operating
4 = Timer relay, operating
Please observe the parts of the operating instructions concerning your particular device.
Fix type identification plate here
Note:
The type identification plate displayed here is identical to that of the supplied pump thus facilitating distinct allocation between the operating
instructions and pump. Please enter the type identification code specified under „Type“ on the type identification plate in the blank line below.
In order to find the description of the properties of the delivered pump quickly and reliably, mark the identification code features concerning
your pump in the following table.

Page 4
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
1 Operating the pump
1.1 Sectional drawing and legend
1 LCD read out
2 Stroke length adjusting knob
3 Program selector key
4 Up/Down keys
5 Stop/Start key
6 Pulse indicating & pilot light, yellow
7 Fault/lack of chemical indicating light, red
8 Power supply
9 Connector for "External/Analog" and remote "on/of" control
with dummy connector
10 Float switch connector, and dummy connector
11 Connector for flow monitor - not available
12 Connection thread (PG 9) for relay output and plug
13 Housing
14 Long stroke solenoid
15 Liquid end with suction and discharge connectors
17 Back-pressure valve with bleeding (17a)
18 Dampener
19 PTFE plunger packing or Bal Seal
20 Oxide ceramics metering plunger
21 Head disk
23 Electronic control with microprocessor
24 Fuse
25 Short description
6421 357 17a 17 15 19 20 18 21 14 13 24 23 25
8 9 10 11 12
2348-2.3

Page 5
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
1.2 Explanation of symbols on pump front panel
Stroke length adjustment
Enclosure rating IP 65
Pilot and pulse indicating light /Pacing relay - optional
Fault indication
Power supply
Connector for external/analog and remote On/Off control
Float switch connector
Connector for flow monitor (curr. not available)
Relay output for peripheral systems
2 Safety instructions
Warning:
Pumps must be accessible at all times for operation and service. Accesses
may not be closed off or blocked!
Warning:
If hazardous or unknown metering media are used, always first empty out the
liquid end and rinse it out for maintenance and repair work!
Observe the safety data sheets of the metering fluids!
Warning:
When metering dangerous or unknown fluids, protective clothing must be
worn when working on the liquid end (glasses, gloves)!
Attention:
Only set the stroke length when the pump is running when the setting bolt of
the metering stroke is briefly relieved!
Please note:
Only use the gripper rings and hose nozzles specified for the respective hose
diameter as well as original hoses with specified hose dimensions and wall
thickness as otherwise the stability of the connection ist not guaranteed!
Avoid reducing the hose sizes!
For long lines and highly viscous media a higher line diameter or a pulsation
dampener should be used!
Caution:
Max. operating pressure 6 bar for 1/8” and 1/6” PTFE lines, applicable to
plug-on system on pipe connection nipple as on mikro g/5a and gamma/ 4
SK pumps.

Page 6
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
3 General description
3.1 Description of function and operation
ProMinent®mikro g/5a solenoid-driven plunger-type metering pump for liquid media
consists of the following components:
Power end
- Housing (13)
- Long stroke solenoid (14)
- Electronic control with microprocessor (23)
- Dampener (18)
- Stroke adjustment (2)
Feeding end
- Liquid end with suction and discharge connectors (15)
- Metering plunger (20)
- Back pressure valve (17)
The pump output has a pulsating flow profile. For every pulse generated by the
electronic circuit a magnetic field is built up in the solenoid coil, and the moveable
supported thrust piece and armature are attracted. The pump plunger displaces the
media in the liquid end through the discharge valve and the balls of the suction valve
close. When the pulse ends the magnetic field becomes de-energised and the thrust
piece with armature and plunger is returned to its original position by means of a
spring. This causes the media to be sucked into the liquid end, the balls on the
discharge side are closed - suction stroke. The oil dampening guarantees an equal
stroke movement for the full stroke length and thus precise metering even with
varying working pressure. The flow output per stroke can be present in a range of
100-2% by means of the stroke length adjusting knob. The stroke length is maximum
10.00 mm.
Stroke length set 0%
0.00 mm
Stroke length set 33%
3.30 mm
Stroke length set 33.2%
3.32 mm
Stroke length set 100%
10.00 mm
release
fix
2350-4

Page 7
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Important: Changes to the stroke length should only be made while the pump is
operating, when the adjustment bolt is temporarily relieved during the metering
stroke.
In the internally controlled, or manual mode, the stroking rate can be varied with the
keys (4) from 0-50 strokes per minute. The settings can be repreated with quartz
accuracy. The output flow is proportional to the stroking rate. The operation and
programming takes place as described in the enclosed instruction manual “ProMinent®
gamma/ 5a”. For the mikro g/5a however the maximum number of strokes per
minute is 50 as opposed to 120 as maximum metering rate and the flow monitor is
omitted.
Operating instructions:
Instruction manual “ProMinent®gamma/ 5a” page 50-73,
Terminal plan page 35
Typical installations page 27-31
3.2 Connection and initial operation
Screw the back pressure valve onto the liquid end. Assemble the metering pump on
a chemical tank or a bracket using screws and washers with a 5 mm diameter. The
valves of the liquid end must always be in a vertical position in order for them to
operate smoothly.
Connect suction and discharge lines.
Installing PTFE tubing on PTFE liquid end
Push screw fitting and sliding ring onto PTFE tube. Heat up the flange pin which
comes with the delivery package to approx. 60-80 °C. Then press the tube with
screw fitting and sliding ring onto the warm flange pin. To press it on a non-slip sand
paper or similar can be used. Please note: The tube should not be bent in doing so.
Connecting thread for screw fitting UNF 1/4”-28.
Installation of VA piping
When laying piping the VA piping length must be adjusted and fitted on the space
available. To cut piping lines it is best to use a piping cutter. For connection to the
feeding end first remove the PTFE tube with nipple. Push terminal nut, thrust collar
and bracing ring onto the pipe. Push the end of the pipe right into the bore. Then
place the thrust collar and the bracing ring on the connection. Screw on terminal nut
and tighten.
2369-4
Flange pin
Detail „X”
M 5:1
max. 5.3 dia.
„X”
Sliding ring
Screw fitting
Connecting thread UNF 1/4”-28
PTFE tube
2-3 mm

Page 8
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
If present connect the float switch or contact/control cable to the pump after
removing the dummy connector or protective cap. The connectors for the contact/
control cable (9) and float switch (10) must be occupied at all times either by a
shunted dummy connector or by the connected control or signal cable and float
switch. For this reason dummy connectors should be kept once they have been
removed. Set the desired flow output using the respective nomogram (see technical
data). Select the desired electronic function in accordance with the following
description:
Sucking and bleeding:
Plug in power into mains socket and set stroke length to 10.00 mm. Then press the
“STOP” key (5) to avoid uncontrolled pumping. Loosen bleed screw (17a) on the
back pressure valve (half a turn). Start automatic quick-priming by simultaneously
pressing the Up and Down keys (4). Keep the keys depressed until the media comes
out of the liquid end. Close the bleed screw.
Important: Do not allow the pump to run dry for a long period as otherwise the
plunger is subjected to increased wear.
Important: Particular care must be taken during the initial operation procedure to
ensure that only Bal-Seal seals are used on pumps for metering demineralised water
(TT3, SS3).
Note: If the metering pump is equipped with valve springs, the intake line must be
filled during initial operation. Self-priming is not possible!
3.3 Operating conditions and directions for use
The admissible ambient temperature is -10 °C (only for media with a freezing point
< -10 °C) up to + 45 °C. If higher temperatures are to be used, the maximum stroke
rate must be lowered from the maximum frequency, for each degree C by approx.
2 strokes per minute.
Relative humidity: 10-92 %, not condensing.
If the pump has been disconnected from the power supply, even after years the
pump always returns to the last mode selected when it is switched on again.
On/off switching by means of connection function is possible with the universal
control cable and voltage-free contact. Switching elements with voltage-free
contact or transistor with open collector. The contact load is approx. 0.5 mA at 5V.
If the pump is to be connected parallel with an inductive power consumer, such as
a solenoid valve or an electric motor, the metering pump must be electrically isolated
when other loads are switched on. The power supply must therefore take place via
an auxiliary contactor or a relay. If this is not possible a varistor (part no. 71.09.12.7)
or a RC combination (0.22 µF/ 470 Ohm) must be connected parallel to render the
harmful induced voltage of the power consumer harmless.
VA-pipe 1/8” or 1/16”
Thrust collar 1/8” or 1/16”
Bracing ring 1/8” or 1/16”
Terminal nut 1/8” or 1/16”
2370-4

Page 9
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Suction capacity
The maximum suction lift of the ProMinent®mikro g/ 5a metering pump with the
liquid end filled is 4-6 m depending on the type of pump (see technical data).
The suction capacity with the liquid end empty is lower (see technical data).
The pump cannot prime against a head.
If the pump feeds into a pressurised system and has accidentally sucked in some
air, this air will only be compressed in the liquid end and no feeding will take place.
In this case the bleed screw on the back-pressure valve is opened about half a turn
and is bled by quick priming (simultaneously pressing the Up and Down keys) until
the suction line and liquid end are filled, free of bubbles. Then retighten the bleed
screw.
If a float switch with early warning is used, the pump will switch into the early warning
status if the first switch point is reached. When the second switch point is reached
(after about 20 mm) the pump switches off so that no air can enter the line system
or the liquid end.
There is opening pressure at the suction and, if the fluid level in the chemical tank
in the operating mode is located above the metering pump and if there is a pressure-
loaded suction line. In this case the back-pressure should be so high that a minimum
differential pressure of 1.5 bar exists. Otherwise an additional back-pressure valve
or a spring-loaded injection valve with an appropriate opening pressure is to be
used.
Important: A back-pressure valve or a spring-loaded injection valve is not a device
which closes absolutely tightly. For this reason the suction side must be fitted with
an isolating valve which is closed when the pump is at a stillstand.
In order to change an output flow which has been set and possibly confirmed by
calibration and to return to the exact same original value, changing the stroking rate
is an option as this is digitally processed and reacts totally linear without mechanics.
3.4 Minor faults, causes and remedies
Pump does not prime in spite of full stroke
movement and proper air bleeding:
Crystalline deposits due to valves drying out. Take suction hose temporarily out of
the chemical tank and rinse out feeding and well. If there is no improvement
disassemble valves and clean them.
Pump does not move, yellow LED does not illuminate,
no indication in the LCD readout:
Check the mains voltage. Have the fuse checked by authorised customer service
personnel and if necessary have it exchanged.
Caution: Only use types which suit the voltage shown on the name plate. If the fault
cannot be remedied by replacing the fuse, have the electronic circuit or whole pump
checked in the factory.
No flow output although yellow indicating light
is flashing:
The stroke lenght is set to zero or too low a valve. Increase stroke length by means
of the stroke adjusting knob (2). Air could have been trapped in the liquid end. This
can be remedied by bleeding as described in section “Suction capacity” (2.3).

Page 10
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Red fault indicating light goes on:
Take note of the flashing fault annunciation on the display.
Further hints see instruction manual g/5a.
Float switch does not switch off the metering pump
when the minimum filling level is reached:
Float is blocked: Remove deposits and clean float.
Other information for operating and maintenance
Changing liquid end and plunger
1. While the pump is working set the stroke length to zero, this blocks the
plunger
2. Push the sliding lock to the front, over the plunger coupling.
3. Disconnect plunger bayonet coupling by pressing and turning to the left.
4. Loosen the knurled screws in front of the liquid end.
5. The liquid end together with the plunger can be pulled off.
6. Install the new or cleaned end in reverse sequence.
52
4
3
3
2378-4
3

Page 11
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Parts subject to wear
In spite of carefully choosing materials and the optimum design of the seals they can
possibly become defective. The plunger V packings are prestressed with disc
springs from the side turned away from the medium so that an automatic adjustment
of the V packing takes place until it is finally worn down. Under certain circumstances
the V packing can also become untight if this has not yet worn down. It can for
example take place due to deposits from carbon abrasion from the V packing onto
the plunger, e.g. during prolonged metering with water with high surface tension.
When the metering plunger sealing is not tight the leaking medium drops out of the
mounting flange between the liquid head and housing.
Remedy:
a) Let the metering pump feed dichloromethane or acetone, the impurity then sorts
itself out, the plunger sealing is once again intact.
b) If this is not successful the V packing is worn out and must be replaced by a new
one.
c) Trouble shooting
If there is no flow from the metering pump due to an unknown reason the nearest
disturbance source is first to be tracked down. Switch on the pump, set maximum
stroke length and stroke frequency, push the sliding lock of the liquid end to the front.
If a stroke movement takes place, the fault must be sought in the liquid end. Loosen
the bleed screw on the back-pressure valve. If this is unsuccessful the valve must
be rinsed with the appropriate media as described above. If there is no stroke
movement at the plunger the electronic circuit is probably faulty. In this case change
the fuse, if necessary the control must be changed at the factory or on location.

Page 12
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
3.5 Installing the liquid end/feeding end plunger
packing (Drawing 1349-3.1)
1. Set the stroke length to 100%.
2. Push on the liquid end, before doing this carefully pull out plunger (6) so far so
that the coupling disc (7) with its longitudinal holes extends over the heads of the
coupling screws (8).
3. Tighten the knurling screws (9). The liquid end ist fastened.
4. Latch the coupling discs (7) on the coupling screws by pressing close and
simultaneously turning to the right. Caution - do not twist the plunger - danger
of it breaking!
5. Check the function, push back the protective liner (10).
967
10 8
On Off
Push & turn
1349-3.1

Page 13
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Installation of packing and plunger (Drawing 2811-3)
1. Push V packing set (1 ) with the opening to the front into the liquid end.
2. Fit pressure disc (2).
3. Fit adjusting washer (3) if necessery.
4. Load the disc spring (4) in opposite surfaces.
5. Assemble clamping disc (5), loosely screw in screws (6) by hand.
Do not tighten!
6. Carefully insert plunger (7).
If the liquid head is to be stored then it should be in this condition.
Before installation on the pump and reuse
With the plunger (7) inserted, screw in screws (6) crosswise onto the clamping
disc (5) until they touch. The liquid end is now ready to operate.
Important!
The plunger may no longer be pulled out of the liquid end when the clamping disc
is tightened. If however this should happen the screws (5) must first be loosened
before the plunger can be pushed into the liquid end.
Please adjuste tolerance balance
measure "A" in case of assembling
with adjusting washer Pos. 3.
Attention!
Please note arrangement of spring-washer.
Only type 2.5/50 TT1, TT2
1 2 3 4 5 6 7
2811-3
Dimension „A”
Type TT1, TT2 SS1, SS2
Ø 2.5/ 50 2.9+0.1 3.9+0.1
Ø 5.0/200 3.2+0.1 3.7+0.1
Ø 8.0/500 3.2+0.1 3.2+0.1

Page 14
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
3.6 Installation of liquid end / feeding end Bal Seal
(Drawing 2053-3)
1. Set the stroke length to 100%.
2. Push the liquid end, before doing this carefully pull out plunger (6) so far that
the coupling disc (7) with its longitudinal holes extends over the heads of the
coupling screws (8).
3. Tighten the knurling screws (9). The liquid end is thus fastened.
4. Latch the coupling discs (7) on the coupling screws (8) by pressing close and
simultaneously turning to the right. Caution - do not twist the plunger -
danger of it breaking!
5. Check the function, push back the protective liner (10).
967
10 8
On Off
Push & turn
2053-3

Page 15
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
3.7 Installation of axial plunger sealing Bal Seal
and plunger
1. Insert guide liner (3) into sealing sleeve (4).
2. Insert axial plunger sealing (2) into sealing bushing (4).
Caution: Observe insertion position!
3. Insert seal (1) in the liquid end.
Push sealing sleeve with guide liner and axial plunger sealing Bal Seal into
liquid end.
4. Put on clamping disc (5). Screw in screws (5) crosswise until they touch.
5. Carefully insert plunger (7).
P
2078-4
2052-3.1
1 2 3 4 5 6 7

Page 16
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
4 Capacity, technical data and nomograms
4.1 Determining the capacity
Please note: In order to obtain a balanced setting, the connection line should be as
horizontal as possible, but however choose a somewhat longer stroke length with
a straight numerical value. For high viscosity media and media tending to emit
vapours and fumes select a large stroke length and a low rate. For precise metering
the stroke length should not be below 2%.
Take the value for the stroke length from the left scale "Setting stroke length" and for
the stroke rate from the "Setting stroke rate" on the right.
Set the metering pump accordingly, adjusting the stroke length only once the pump
is operating.
The measurements of the flow rate have been carried out with water.

Page 17
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
4.2 Nomogram for determining flow output
of the ProMinent®mikro g/5a, Type 400150
Revolution, digital display
Stroke length (%)
Flow rate (ml/h)
Stroke rate (strokes/min)
2748-4
Nomogram for the determining flow output
of the ProMinent®mikro g/5a, Type 180600
Revolution, digital display
Stroke length (%)
Flow rate (ml/h)
Stroke rate (strokes/min)
2749-4

Page 18
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
Nomogram for determining flow output
of the ProMinent®mikro g/5a, Type 061500
Diagram for determining the flow rate
relative to stroke length
Revolution, digital display
Stroke length (%)
Flow rate (ml/h)
Stroke rate (strokes/min)
2750-4
Stroke length (%)
2440-4.1
Discharge amount (µl/stroke)
Type 061500
Type 180600
Type 400150

Page 19
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
4.3 Performance data mikro g/5a
Pump type 400150 180600 061500
Plunger diameter/
Stroke volume mm/µl 2.5/50 5/200 8/500
at max. pressure bar 40 18 6
max. output flow
(at 50 strokes/min.,
100% stroke) ml/h 150 600 1500
µl/strokes 50 200 500
Suction lift mWC 6 6 4
Priming lift*** mWC 1 3 3
Permis. open. press.
suction end bar 25* 10* 3
Back-pressure valve
Head pressure bar 2.5 2.5 1.5
* = PTFE version max. 10 bar
** NPSH nec. = minimum nec. pressure on suction
end of the metering pump
(NPSH) = Net Positive Suction Head
*** = Priming lifts with clean and wetted valves with water and suction line
as specified.
Metering accuracy: The reproducibility of the metering is better than ±0,5% of
the value set in the stroke length range of 10% to 100% under defined and
constant conditions and correct installation.
4.4 Electrical data and enclosure rating mikro g/5a
Solenoid diameter: mm 90
Max. stroke rate: strokes/min. 50
Current consumption at dosing impulsion:
230 V version A 0.28
115 V version A 0.54
Mean power consumption:
230 V version watts 31
115 V version watts 23
Fuse:
230 V version 0.2 ATT Little fuse, Part no. 712034
115 V version 0.4 ATT Little fuse, Part no. 712036
Power supply: 230 V version ±10%, 50/60 Hz
115 V version ±10%, 50/60 Hz
Control voltage: 5 V
Minimum duration of pacing
pulse (external control): 20 ms
Contact load: 1 mA
Enclosure rating: IP 65
Further hints see instruction manual g/5a.

Page 20
ProMinent®mikro g/5a
Precision feeding pump Instruction manual
mikro g/5a
4.5 Pump specific data mikro g/5a
Pump type 400150 180600 061500
Connectors discharge Steel vers. dia.1.5 dia.1.5 dia. 3.175
and suction side Pipe o/d.
PTFE vers. 1.75 x 1.15 1.75x 1.15 3.2 x 2.4
Tube o/d x i/d
Shipping weight net PTFE 5.6 5.6 5.6
without packaging (kg) Stainl. Steel 5.9 5.9 5.9
(with packaging
+ 1.5 kg)
Dimensions: S... T... S... T... S... T...
Length (mm) 371 371 371 371 373 373
Width (mm) 124 124 124 124 124 124
Height (mm) 224 227 224 227 252 235
Materials in contact with the medium
Stainless Steel vers. PTFE version
Liquid end 1.4571 Carbon loaded PTFE
Valves & connectors 1.4571 Carbon loaded PTFE
Valve ball Ruby Ruby
Valve face Ceramic Ceramic
Metering plunger Ceramic Ceramic
Valve seal PTFE PTFE
Plunger sealing PTFE (SS1) PTFE (TT1)
PTFE+ graphite (SS2) PTFE+ graphite (TT2)
Bal Seal (SS3) Bal Seal (TT3)
Subject to technical alterations.
ProMinent Dosiertechnik GmbH
Im Schuhmachergewann 5-11
D-69123 Heidelberg
Postfach 10 17 60
D-69007 Heidelberg
Telephone: [phone]
Fax: [phone]
eMail: [email protected]