Prorack K131 User manual

K131
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 2 x 2
x 4 x 1 x 4
Revision No: 3C 1

Fitting Kit K131
MAX kgs (lbs)
W/P WHD
Toyota
Estima, 5dr MPV 00-Apr 06 NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Previa, 5dr MPV 00-06 EU 60 kgs (132 lbs) 60 kgs (132 lbs)
Previa, 5dr MPV 00-Apr 06 NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Tarago, 5dr MPV Jun 00-Mar 06 AU 60 kgs (132 lbs) 60 kgs (132 lbs)
2

Fitting Kit K131
X
A B C 1 2 3
Estima, 5dr MPV 00-Apr 06 (NZ) 200mm 810mm - 811mm 776mm -
7 7/8ths" 31 7/8ths" - 31 15/16ths" 30 9/16ths" -
Previa, 5dr MPV 00-06 (EU) 200mm 810mm - 811mm 776mm -
7 7/8ths" 31 7/8ths" - 31 15/16ths" 30 9/16ths" -
Previa, 5dr MPV 00-Apr 06 (NZ) 200mm 810mm - 811mm 776mm -
7 7/8ths" 31 7/8ths" - 31 15/16ths" 30 9/16ths" -
Tarago, 5dr MPV Jun 00-Mar 06 (AU) 200mm 810mm - 811mm 776mm -
7 7/8ths" 31 7/8ths" - 31 15/16ths" 30 9/16ths" -
3

Fitting Kit EN
K131
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K131
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K131
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 332A
B = 333A
6

Fitting Kit EN
K131
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
7

Fitting Kit EN
K131
●Make sure the pad fits into the holes
underneath the foot.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Attaches to factory-fitted mounting points
under sliding doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Press adjusting screw to adjust the leg
positions on the crossbar.
8

Fitting Kit EN
K131
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Place clamp over the mounting hole
●Fit a fibre washer on each capscrew and
attach clamps to the vehicle body using the
capscrews.
●Tighten locking screw on both legs evenly.
9

Fitting Kit EN
K131
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10