Prorack K751 User manual

K751
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
x 1 x 1 x 1 x 1
Revision No: 2B 1

Fitting Kit K751
MAX kgs (lbs)
W/P WHD
Opel
Astra, 4dr Sedan 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 4dr Sedan 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
New Astra, 4dr Sedan 13-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K751
X
A B C 1 2 3
Astra, 4dr Sedan 13-+ (EU) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
Astra, 4dr Sedan 13-+ (EU) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
New Astra, 4dr Sedan 13-+ (ZA) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
3

Fitting Kit EN
K751
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K751
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K751
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K751
Fitment
●Open or remove fixed-point covers.
●Locate fixed clamping block A
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 095
B = 096
●Hook small claw into rear of the clamping
block
●Hook large claw into front of the clamping
block
7

Fitting Kit EN
K751
●Refer to the underside of the pad for the
part number.
●Letters refer to the pad part numbers and
position.
●It is important to put the pads in the correct
position on the vehicle.
●Pad Part Number:
A = 233
B = 234
C = 267
D = 268
●Ensure internal clamp sits upright.
●Fit pad carefully over fixed point and clamp
screw.
8

Fitting Kit EN
K751
●Mount crossbars over clamps.
●Repeat for all legs.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
9

Fitting Kit EN
K751
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10