Protekt ABM/LB101 User manual

REQUIRED FREE DISTANCE BELOW WORKING LEVEL FOR WORKER PROTECTED WITH ENERGY ABSORBER WITH LANYARD
!free distance below working surface must be 6,2 m (see drawing no.1)
!drawings no.2 and no. 3 show free distance below working surface depending on location of Structural Anchor Point.
The energy absorber with lanyard is a component of personal fall arrest equipment and complies with EN355.
Fall arrest system consisted of energy absorber with lanyard, attached to the full body harness (complied with EN 361) and connected to the structural
anchor point (complied with EN 795) can be used as a basic personal protective equipment against falls from a height.
Caution: The total length of the energy absorber with lanyard including terminations and connectors shall not exceed 2 m.
(e.g. connector plus lanyard plus energy absorber plus connector)
~1,5 m
~1,5 m
~1,5 m
~4,7 m
~3,2 m
~6,2 m
2
13
3,5 m - free fall
Structural Anchor Point
min. 12 kN
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
+1 m - security
1,8 m - man height
2 m - free fall
Structural Anchor Point
min. 12 kN
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
1,8 m - man height
+1 m - security
Structural Anchor Point
min. 12 kN
0,5 m - free fall
1,2 m - ultimate
elongation
of the energy
absorber
0,2 m - displacement
of the back attaching buckle
1,8 m - man height
+1 m - security
EN 355:2002
Instruction Manual
Read carefully
the manual
before use
the equipment
ENERGY ABSORBER
w i t h l a n y a r d
ATTENTION! The energy absorbers can be equipped only with certified (according to EN362) connectors.
Ref.: BW 200/LB101
EN 355:2002
ENERGY ABSORBER WITH LANYARD LB101
Serial
number: 0000001
Date
of manufacture: 03.2017
A B M / L B 101
CONTENT OF THE DEVICE IDENTITY LABEL
Energy absorber is made of 32 mm wide webbing. Absorber is equipped with attachment loops on the endings. One of the loops is connected
to the lanyard. The body of the absorber is protected by a special jacket made of a shrinkable, polyethylene tube. The lanyard can be made of:
- 10,5 mm polyester kernmantle rope eneded with sewn loops (ABM/LB101, ABM/LB102).
- ø12 mm polyester kernmantle rope eneded with sewn loops (ABM/LB121, ABM/LB122).
- ø14 mm polyester kernmantle rope eneded with sewn loops (ABM/LB141).
- ø12 mm polyester kernmantle rope eneded with sewn loops. One loop is adjustable by steel adjustment buckle (ABM/LB100, ABM/2LB100).
- tubular polyamide webbing with elastic core inside. The endings of the lanyard are sewn making the attachment loops (ABM/ LE101, ABM/2 LE101).
- 30 mm polyester webbing eneded with sewn loops equipped with thimbles (ABM-T, ABM-2T)
polyamide
ø
CONSTRUCTION
the maximum length of the energy absorber with lanyard can’t exceed 2 m
A
B
C
D
E
F
G
H
I
A. type of the device
B. marking of the model of energy absorber
C. reference number of the device
D. CE marking with identity number of the notified body
controlling manufacturing of the equipment
(the article 11)
E. European standards (number/year)
F. month/year of the device manufacture
G.
H. caution: read the manual
I. marking of the manufacturer or distributor
number of the manufacturing series
1. absorber's attachment loop ; 2. energy absorber ; 3. lanyard ; 4. lanya 5. thimble ; 6. lanyard's seam; 7. adjustment buckle ;
8. identity label. rd's attachment loop ;
Ref. BW 200/LB 141
ABM/LB141
Ref. BW 200/LB 121
ABM/LB121
Ref. BW 200/LB 101
ABM/LB101
1
2
3 4
66
8 1
2
3 4
66
8 7
Ref. BW 200/LB 100
ABM/LB100
Ref. BW 200/LE 101
ABM/LE101
1
2
8
55
3 4
6 6
1
26
8 3
5
4
6
1
26
8 3
5
4
66
1
2
8
4
6
3
6
Ref. BW 200/LB 102
ABM/LB102
Ref. BW 200/2 LB 100
ABM/2LB100
Ref. BW 200/2 LE 101
ABM/2LE101
1
1
2
8
2
ABM-T
8
ABM-2T
6
6
Ref. BW 700
3
Ref. BW 800
4
6 5
3
4
5
6
Ref. BW 200/LB 122
ABM/LB122
IDENTITY CARD
SERIAL NUMBER
USER NAME
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DATE OF PURCHASE
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED. THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A
COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT. ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF
EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON. THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT
UTILIZATION. DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD. ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
PERIODIC EXAMINATION AND REPAIR HISTORY
DATE
REASON FOR
ENTRY PERIODIC EXAMINATION
OR REPAIR
DEFECTS NOTED,
REPAIRS CARRIED OUT
AND OTHER REVELANT INFORMATIONS
NAME AND SIGNATURE
OF COMPETENT PERSON
PERIODIC
EXAMINATION
NEXT DUE DATE
1
2
3
4
6
Periodic inspections
The device must be inspected at least once every 12 months from the date of first use.
Periodic inspections must only be carried out by a competent person who has the knowledge and training required for personal protective equipment
periodic inspections. Depending upon the type and environment of work, inspections may be needed to be carried out more frequently than once every
12 months. Every periodic inspection must be recorded in the Identity Card of the equipment.
Maximum lifespan of the equipment
The maximum lifespan of the energy absorber with lanyard is 10 years from the date of manufacture.
The energy absorber with lanyard must be withdrawn from use immediately and destroyed when it has been used to arrest a fall or it fails to pass inspection or
there are any doubt as to its reliability.
ATTENTION: The lifetime of the device depends on the intensity of usage and the environment of use. Using the device in rough environment, marine
environment, contact with sharp edges, exposure to extreme temperatures or agressive substances, etc. can lead to the wthdrawal from use even after one
use.
PROTEKT
93-403 LODZ, ul. Starorudzka 9, POLAND,
TEL: [phone], FAX: [phone]
www.protekt.com.pl
Notified body, at which the European certification was Iissued and which supervises
the production of the equipment:
APAVE SUDEUROPE SAS - 8 rue Jean-Jacques Vernazza - Z.A.C. Saumaty-Séon
CS-60193 – 13322 MARSEILLE Cedex 16, France - No. 0082

!personal protective equipment shall only be used by a person trained and competent in its safe use.
!personal protective equipment must not be used by a person with medical condition that could affect the safety of the
equipment user in normal and emergency use.
!a rescue plan shall be in place to deal with any emergencies that could arise during the work.
!it is forbidden to make any alterations or additions to the equipment without the manufacturer's prior written consent.
!any repair shall only be carried out by equipment manufacturer or his certified representative.
!personal protective equipment shall not be used outside its limitations, or for any purpose other than that for which it is
intended.
!personal protective equipment should be a personal issue item.
!before use ensure about the compatibility of items of equipment assembled into a fall arrest system. Periodically check
connecting and adjusting of the equipment components to avoid accidental loosening or disconnecting of the components.
!it is forbidden to use combinations of items of equipment in which the safe function of any one item is affected by or interferes
with the safe function of another.
!before each use of personal protective equipment it is obligatory to carry out a pre-use check of the equipment, to ensure that
it is in a serviceable condition and operates correctly before it is used.
THE ESSENTIAL PRINCIPLES FOR USERS OF PERSONAL PROTECTIVE EQUIPMENT AGAINST FALLS FROM A HEIGHT
2
1. Attach the energy
absorber's connector to a
frontal or dorsal
attachment point of full
body harness (conformed
to EN 361) - [1]
2. Connect the lanyard's
connector to the
structural anchor point of
resistance min. 12 kN
(conformed to EN 795)
placed above the user:
- directly [2]
- with a additional
connector [3], [4]
The shape of the structural
anchor point shall not let self-
acting disconection of the
device.
WARNING:
During use the energy
absorber with double lanyard
(ABM/LB102, ABM/LB122,
ABM/2LB100, ABM/2LE101,
ABM-2T) it is strictly forbidden
to attach the one lanyard's
connector to harness
attachment element and the
second lanyard's connector to
structural anchor point [5].
!
!1
WARNING !
NECESSARILY PROTECT
THE SNAP HOOK GATE
WITH THE LOCKING GEAR
3 4
ASSEMBLING A FALL ARREST SYSTEM
- The user should minimise the amount of slack in the lanyard near a fall hazard.
- The user must rule out any risk of the situation (e.g. wrapping the lanyard around neck) that during use ar arresting a fall the lanyard may
be used choke hitched.
- The user should avoid interleaving the lanyard between construction elements or the situation when there is a risk of falling over the
sharp edge (e.g. roof edge).
0 0
- The energy absorber with lanyard can be used in temperatures from -30 C to 50 C.
- Two separate lanyards each with an energy absorber should not be used side by side (i.e. parallel).
- The free lanyard of a double (twin tail) lanyard combined with energy absorber should not be clipped back on the harness.
!during pre-use check it is necessary to inspect all elements of the equipment in respect of any damages, excessive wear,
corrosion, abrasion, cutting or incorrect acting, especially take into consideration:
- in full body harnesses and belts - buckles, adjusting elements, attaching points, webbings, seams, loops;
- in energy absorbers - attaching loops, webbing, seams, casing, connectors;
- in textile lanyards or lifelines or guidelines - rope, loops, thimbles, connectors, adjusting element, splices;
- in steel lanyards or lifelines or guidelines - cable, wires, clips, ferrules, loops, thimbles, connectors, adjusting elements;
- in retractable fall arresters - cable or webbing, retractor and brake proper acting, casing, energy absorber, connector;
- in guided type fall arresters - body of the fall arrester, sliding function, locking gear acting, rivets and screws, connector,
energy absorber;
- in connectors - main body, rivets, gate, locking gear acting.
!after every12 months of utilization, personal protective equipment must be withdrawn from use to carry out periodical detailed
inspection. The periodic inspection must be carried out by a competent person for periodic inspection. The periodic inspection
can be carried out also by the manufacturer or his authorized representative.
In case of some types of the complex equipment e.g. some types of retractable fall arresters the annual inspection can be
carried out only by the manufacturer or his authorized representative.
!regular periodic inspections are the essential for equipment maintenance and the safety of the users which depends upon the
continued efficiency and durability of the equipment.
!during periodic inspection it is necessary to check the legibility of the equipment marking.
!it is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall
provide instructions for use, for maintenance, for periodic examination and for repair in language of the country in which the
product is to be used.
!personal protective equipment must be withdrawn from use immediately when any doubt arise about its condition for safe use
and not used again until confirmed in writing by equipment manufacturer or his representative after carried out the detailed
inspection.
!personal protective equipment must be withdrawn from use immediately and destroyed when it have been used to arrest a fall.
,
!a full body harness is the only acceptable body holding device that can be used in a fall arrest system.
!in full body harness use only attaching points marked with big letter "A" to attach a fall arrest system.
!the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a
way, as to minimise both the potential for falls and potential fall distance. The anchor device/point should be placed above
the position of the user . The shape and construction of the anchor device/point shall not allowed to self-acting disconnection
of the equipment. Minimal static strength of the anchor device/point is 12 kN. It is recommended to use certified and marked
structural anchor point complied with EN795.
!it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest
system, so that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path. The required
value of the free space should be taken from instruction manual of used equipment.
!there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to
be observed during equipment utilization, especially:
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
!personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or
cases made of steel or plastic) to protect it against damage or moisture.
!the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile
products use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be
cleaned only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed
to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.)
can be regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
!personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light,
ultraviolet degradation, damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.
!using the energy absorber in connection with fall arrest system must be compatible with use instructions of the fall arrest
systems and obligatory standards:
- EN 361 - for safety harnesses
- EN 362 - for connectors
- EN 795 - for anchorages
- EN 354 - for lanyards
CAUTION
FORBIDDEN!
5