PRYME PRYMEBLU BTH-600 User manual

Installing or Replacing the Battery Pack
The BTH-600 Bluetooth speaker microphone gets its power from a rechargeable Lithium-Ion type battery pack. The
battery pack must be installed inside the microphone prior to operation. Under normal usage, this battery should
have a lifespan of over 1,500 charge/discharge cycles before needing to be replaced.
To access the battery compartment:
1. Rotate the clothing clip on the back of the speaker microphone 90° to expose the thumbscrew at the top of
the battery compartment cover. Rotate the thumbscrew counter-clockwise until the cover opens. Remove the
battery door.
2. Insert the rechargeable battery pack into the battery compartment. Ensure that the battery terminals are
properly lined up with the contacts inside of the battery compartment.
3. Reinstall the battery compartment cover and rotate the thumbscrew clockwise to tighten. Do NOT over tighten.
Pairing with a PRYMEBLU Radio Adapter and 2-way Radio
When pairing the PRYMEBLU Speaker Microphone with a PRYMEBLU Radio
Adapter, make sure that the speaker microphone, adapter, and the
two-way radio the adapter is connected to are all powered o to start.
If your PRYMEBLU Radio Adapter gets power directly from the two-way radio it is attached to:
•Hold down the Talk button on the PRYMEBLU Radio Adapter while turning the two-way radio ON.
If your PRYMEBLU Radio Adapter has its own charger/internal battery pack:
•Turn the power switch on the PRYMEBLU Radio Adapter to the ON position while holding down the
multifunction Talk button on the PRYMEBLU Radio Adapter.
•Continue to hold the Talk button on the adapter down for approximately three seconds. Release the Talk
button when the status LED on the PRYMEBLU Radio Adapter begins to ash two times per second. The
PRYMEBLU Radio Adapter is now in audio accessory pairing mode.
•Hold down the Multifunction Button on the PRYMEBLU Speaker Microphone. Continue to hold the button
down for approximately 3 seconds, until you see the LED on the speaker microphone begin to quickly ash
RED-BLUE-RED-BLUE in sequence. The PRYMEBLU Speaker Microphone is now in pairing mode.
•After a few seconds, the two devices should synch to one another. Once the PRYMEBLU Speaker
Microphone and Adapter are paired with each other the status LED on the adapter will show a constant blue
light for three seconds. The LEDs on both the adapter and speaker microphone will then show one FLASH
every few seconds.
•If the PRYMEBLU Radio Adapter does not detect the speaker microphone within 60 seconds of being put into
pairing mode, the adapter will exit the pairing mode and resume normal operation.
•Once successfully paired, you will be able to operate your 2-way radio using the PRYMEBLU Speaker Mic.
Reconnecting a Previously Speaker Microphone and Radio Adapter
Once the PRYMEBLU Speaker Microphone and Radio Adapter have been successfully paired together, both
devices will remember that connection. The adapter and speaker mic will attempt to reestablish their link
whenever the radio/adapter and microphone are both powered on and in within range of each other.
Re-establishing this connection can take 10-60 seconds.
3 4
Charging the Speaker Microphone
2
Controls and Connection
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. RF Exposure Warning! This device contains transmitters and receivers which emit Radio Frequency (RF) energy. The device is designed to comply with the limits for exposure to RF energy set by the Federal Communications Commission (FCC) of the United States, Industry Canada (IC) of Canada, and the regulating entities of other countries. If you are still concerned about exposure to RF energy, you can further limit your exposure by limiting the amount of time you use the equipment or by placing more distance between your body and the device, since exposure level drops o dramatically with distance.
1.0 January 2015
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: [phone]
TOLL FREE: 800.666.2654
WWW.PRYME.COM
PRYMEBLU BTH-600
Wireless Bluetooth Speaker Microphone
For use with PRYMEBLU radio adapters and cellular phones PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products, Brea CA. All other product or service names are the property of their respective owners. © 2015 PRYME Radio Products, Brea CA. All Rights Reserved
Phone Button
This button is used to
answer or hang up
telephone calls when the
BTH-600 is connected to
a cellular phone.
To charge the speaker microphone
1. Ensure the device is turned o using the multifunction button.
2. Plug the charge cable into any powered USB outlet,
such as an AC wall charger, and then into the charge jack
on the bottom of the speaker microphone. You will need to
remove the protective rubber cover that is inserted into the
charge jack. (To prevent dust and moisture from damaging
your speaker microphone, always ensure this cover is in place
when you are not charging.)
3. Once the charging process has begun, the LED indicator
on the bottom of the speaker microphone will show a constant red light.
4. Typical charge time is approximately ve hours. Actual charge time will vary depending
on several factors including the battery’s charge state, condition, and age.
5. When the battery is fully charged the LED indicator on the side of the speaker microphone
will show a constant green indication.
6. Disconnect the charger from the adapter when charging is completed.
Charging Cautions:
- Do not use a wall charger or charge cable that appears to be damaged. (Example: frayed wires,
melted plastic, etc.) Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the speaker microphone or charger.
- Always turn the speaker microphone o when charging.
The BTH-600 speaker microphone has a replaceable
Lithium Ion rechargeable battery pack which must
be charged prior to operation, and must be
recharged regularly. A fully charged battery will
provide up to 40 hours of continuous operation
before needing to be recharged. However,
operating time can vary depending on usage and
the condition of the battery pack. Recharge the
battery regularly.
Model No.: BTH-600 Made in Taiwan
Front Firing Speaker
Received calls are heard over this speaker.
The volume level can be controlled using
either the Volume Up / Down buttons on
the speaker microphone, or by using the
volume controls on the
two-way radio or phone.
Status LEDs
The red and blue LEDs ash
messages that let the user
know the current status of
the speaker microphone.
Clothing Clip
The alligator-type clip secures the
speaker microphone to the user’s
clothing during use. The clip can be
rotated to allow the microphone to
be better positioned.
Multifunction Button
Holding down this button for one second
will turn the speaker microphone on and o.
This button can also be used to place the speaker
microphone into pairing mode so that it can be
connected wirelessly to a cellular phone.
Microphone:
This microphone picks up the user’s
voice audio when sending a call.
PTT Button
This button is used to
activate the push-to-talk
feature of the 2-way radio Volume Up and Down Buttons
These buttons can be used to turn
the receive audio volume of the
speaker microphone up or down
in ve preset steps.
Charge Jack
This mini-USB jack is used to recharge the
removable battery of the speaker microphone
by connecting the BTH-600 to a USB charger
or any powered USB source
Earphone Jack
This jack is used to connect an (optional)
wired listen-only earphone to the speaker
microphone for enhanced privacy.
Battery Cover
The rear cover of the speaker
microphone can be removed
by loosening the thumbscrew
on the rear of the microphone.
This allows the user to gain access
to the removable battery pack.
Removable Battery
The speaker microphone is
powered by a removable Lithium
battery pack
1 2

Pairing with a Cellular Telephone
The PRYMEBLU Bluetooth Speaker Microphone is capable of working with a Bluetooth-enabled cellular
telephone. The speaker microphone is even capable of simultaneously pairing with both a PRYMEBLU
Radio Adapter and a cell phone, enabling you to use the same speaker microphone for both radio and
telephone calls.
NOTE: If you wish to use the multi-pairing feature
to connect the BTH-S600 to both a PRYMEBLU Radio
Adapter and a cellular phone, you must rst pair the
PRYMEBLU Speaker Microphone and PRYMEBLU Radio
Adapter using the procedure shown on Page 4 of this
manual. Once the two devices have been paired to
each other, power the two-way radio/Bluetooth Radio
Adapter o, and follow the procedure shown below:
When pairing the PRYMEBLU Speaker Microphone with a cellular phone, make sure that the speaker
microphone and all other nearby Bluetooth devices are powered o¬ before beginning.
•Hold down the Multifunction Button on the PRYMEBLU Speaker Microphone. Continue to hold the button
down for approximately 3 seconds, until you see the LED on the speaker microphone begin to quickly ash
RED-BLUE-RED-BLUE in sequence. The PRYMEBLU Speaker Microphone is now in pairing mode.
•Activate the Bluetooth feature on your phone.
•Activate the “scan/discover new Bluetooth devices” feature on the phone. The exact steps needed to do
this will vary depending on the brand/model of phone you are using.
•Select the PRYMEBLU Speaker Microphone from the list of Bluetooth devices shown on your phone. If the
phone asks for a passcode, enter “0000”. The phone may also prompt you to conrm the connection.
•After a few seconds, the two devices should synch to one another. Once the PRYMEBLU Speaker
Microphone and phone are paired with each other, the status LED on the microphone will revert back to a
single blue ash every few seconds.
•Once successfully paired, you will be able to make and receive telephone calls using the PRYMEBLU
Speaker microphone.
Multi-Pairing Operation
Once you have successfully paired the PRYMEBLU Speaker Microphone and cellular phone, you can enable
multi-pairing operation simply by powering on the two-way radio/PRYMEBLU Radio Adapter that you
previously paired with the PRYMBLU Speaker Microphone. Within a few seconds, all three devices should
synch to each other.
8
65
7
STATUS LED MESSAGES
The meanings of the various status LED messages shown by the speaker microphone are
shown on the following table:
OPTIONAL EAPRHONES
Although the BTH-600-ZD has a built-in speaker for listening to received calls,
some users may prefer to use a listen only earphone for enhanced privacy.
The accessory jack on the speaker microphone will accept any mono
earphone with a 3.5 mm audio plug.
When an earphone is used, the
front-ring speaker is disabled.
PRYME EH-1389SC model shown.
Earphone sold separately.
PRYME makes a variety of listen-only earphones in
dierent styles that will work with the BTH-600.
SPECIFICATIONS
Using the PRYMEBLU Speaker Microphone
Once your PRYMEBLU Speaker Microphone and PRYMEBLU Adapter and/or cellular phone have been
paired together:
Received signals will be heard over your PRYMEBLU Speaker Microphone’s front- ring speaker or
through the optional earphone. The volume of received calls can be adjusted using the volume
up/down button on the speaker microphone or the volume control on the two-way radio or cellular
phone.
When transmitting or on a phone call, the operator’s voice is picked-up by the microphone in the
PRYMEBLU Speaker Microphone.
Push-to-Talk can be activated one of several di¬erent ways:
• By pressing and holding the PTT button on the PRYMEBLU Speaker Microphone.
• By pressing and holding the Talk button on the PRYMEBLU Adapter.
• Using an optional wired PTT that is plugged into the PRYMEBLU Adapter.
• Using an optional PRYMEBLU Wireless Bluetooth PTT (model BT-PTT2, sold separately). Note that if
you are using a PRYMEBLU BT-PTT2, you will rst need to pair the adapter with the PTT using the
instructions located in the PRYMEBLU PTT User’s Guide.
To answer or hang up a cellular telephone call, press the orange Phone Button on the side of the
speaker microphone or use the user interface on the phone itself.
You can also activate your phone’s voice dialing feature by pressing and holding the Phone Button
on the side of the microphone for three seconds. (This function works only when the microphone is
NOT connected to a two-way radio.)
NOTE: When you are on a phone call, signals received by the two-way radio will not be heard.
Additionally, if you press the PTT button on the PRYMBLU Speaker Microphone while you are on a
phone call, the two-way radio will transmit, however no transmit audio will be sent over the air, since
microphone audio is being routed to the cellular phone.
LED INDICATION
Constant Red (while plugged into charger)
Constant Green (while plugged into charger)
Flashes red-blue-red-blue repeatedly
Two blue ashes every two seconds
One blue ash every two seconds
Constant red with one blue ash every two seconds
No indication
MEANING
Charge mode
Charging is nished
Pairing mode
Speaker microphone is powered on but not paired
Speaker Microphone is powered and paired
PTT is pressed
Speaker microphone is powered o
SUPPORT AND WARRANTY
PRYME Radio Products warrants this product against defects in materials or workmanship for a
period of one year from the date of retail purchase. PRYME will repair or replace a defective unit,
at our option, without charge for parts or labor. The limited warranty is extended only to the
original purchaser and is valid only to consumers in the United States and Canada. It does not
cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper or
abnormal usage, faulty installation, improper maintenance, lightning, or other incidences of
excessive voltage, or any tampering or repairs by other than a PRYME authorized repair facility. It
does not cover replacement of consumable parts, transportation costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms of this
warranty. This warranty can only be modied by an ocer of PRYME Radio Products, and then
only in writing. Should this product prove defective in workmanship or material, the consumer’s
sole remedies shall be such repair or replacement as provided by the terms of this warranty.
Under no circumstances shall PRYME Radio Products be liable for any loss or damage, direct,
consequential, or incidental, arising out of the use of or inability to use this product. Some states
do not allow limitations on how long an implied warranty lasts or the exclusions or limitations of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specic legal rights. You may also have other rights, which may vary,
from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-2654 or visit us
on the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2015 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products, Brea CA.
Android is a trademark of Google Inc.
All other product or service names are the property of their respective owners.
DISCLAIMER: The Bluetooth wireless link used by PRYMEBLU products is an open
standard, unsecured technology. As such, it is not recommended for rst-responder or
other mission critical users.
Bluetooth Version:
Speaker Output:
Receiver Sensitivity:
Power Class:
Range:
Display:
Bluetooth Prole:
Operating Voltage:
Battery Capacity:
Operating Time (Standby)
Operating Time (Typical)
Operating Time (Continuous Talk)
Push-to-Talk Function:
Operating Temperature:
v2.1+EDR
1 watt
-82 dBm (typ.)
Bluetooth class 2
10 meters
Blue, Red, and Green
HFP,HSP,SPP Prole
5 VDC
1,020 mAH
> 30 days
> 80 hours
> 40 hours
Built-in
-70°F to +120°F (approx.)
Model
EH-389SC
EH-389XC
EH-1289SC
EH-1289XC
EH-1389SC
EH-1389XC
EH-1399X
EH-GH89-SC
Model
Rubber Ear Hook
Rubber Ear Hook
Plastic D-Ring
Plastic D-Ring
Acoustic Tube
Acoustic Tube
Acoustic Tube
G-Hook (swivel)
Cable Length/Type
15” Coiled
25” Coiled
15” Coiled
25” Coiled
15” Coiled
30” Straight
30” Straight
10” Coiled
Connector
3.5mm right angle
3.5mm right angle
3.5mm right angle
3.5mm right angle
3.5mm right angle
3.5mm right angle
3.5mm right straight
3.5mm right angle