PSA LIFESAVER LIF10YPEW User manual

1
0
3
1
9
-
7
2
0
2
-
0
0
Quick
Start Guide
LIF10YPEW Interlink Network Setup
Please Read All Instructions First!

2
Section 1
Quick Start RF Interlink Network Setup
Section 2
Adding a Device to an Existing
RF Interlink Network
Section 3
Resetting a Device
1
Power Up ONE Device
Rotate one unit completely onto the
mounting bracket to activate power.
One chirp when powered, and the Red
LED will glow on/o every second.
Install
Remove

3
Section 1
Quick Start RF Interlink Network Setup
Section 2
Adding a Device to an Existing
RF Interlink Network
Section 3
Resetting a Device
1
Power Up ONE Device
Rotate one unit completely onto the
mounting bracket to activate power.
One chirp when powered, and the Red
LED will glow on/o every second.
Install
Remove

4
Push the button two times on the rst
powered device.
2 soft beeps and 2 Red LED ashes
every 2 seconds with a "sonar" ping sound.
This is the network coordinator.
Join Mode is open.
Push button twice
2
On the First Powered Device

5
3
Power up Remaining Devices
Power up all of the remaining devices
by rotating them completely onto their
mounting brackets.
One chirp at power on. Each unit gives a
tweedle sound and Red LED ashes
3 times every 2 seconds after
joining the network.
Install
Remove

6
Push the button twice on any unit that
was powered and joined the network.
Red LED stops ashing on each unit
as network is closed.
Push button twice
4
Pick Any Device

7
5
If all devices are no longer ashing the
Red LED, and the "sonar" ping has stopped,
the devices are now connected.
Congratulations!
Setup Complete!
Please mount alarms in your home.
Refer to user guide for detailed
installation instructions.

8
Section 2
Adding a Device
to an Existing RF Interlink Network
To open the RF Interlink Network,
push the button twice on any previously
connected LIF10YPEW unit
Soft beeps and Red LED ashes every
2 seconds with a "sonar" ping sound.
Join Mode is open.
Push button twice
1
Push Button Twice on
any Installed unit.

9
To open the RF Interlink Network,
push the button twice on any previously
connected LIF10YPEW unit
Soft beeps and Red LED ashes every
2 seconds with a "sonar" ping sound.
Join Mode is open.
Push button twice
1
Push Button Twice on
any Installed unit.

10
2
Power On the New Device(s)
Rotate the new device(s) completely
onto the mounting bracket(s).
One chirp at power on.
Each new unit gives a tweedle sound and
Red LED ashes 3 times every 2 seconds
after joining the network.
Install
Remove
Push button twice on any connected
device to close the network.
Red LED stops ashing on
each unit as network is closed.
3
Choose ANY Connected Device

11
Push button twice on any connected
device to close the network.
Red LED stops ashing on
each unit as network is closed.
3
Choose ANY Connected Device

12
4
If all devices are no longer ashing the
Red LED, and the "sonar" ping has stopped,
the devices are now connected.
Congratulations!
Setup Complete!
Please mount alarms in your home.
Refer to user guide for detailed
installation instructions.

13
Section 3
If you encounter an issue at any point
during the RF Interlink network setup process,
or if you need to remove a device from a network,
you may reset the device by following
the subsequent directions.
Resetting Your Device

14
Push button twice to open Join Mode.
Unit will respond with 2 or 3 ashes,
indicating Coordinator or RFD respectively.
Sonar Ping will sound.
1
Resetting the Device

15
Press and Hold button for 4 to 5 seconds.
Unit will respond with 2 soft beeps and
4 quick ashes indicating that the wireless
settings have been reset and the unit is now
a standalone alarm.
Device has been put in General Reset Condition.
See User Guide for complete instructions
on how to return to a network
2
Push and
hold button
Resetting the Device

16
Need more help
getting started?
Consult the User Guide for more detailed
instructions on product installation and use.
Visit www.psaproducts.com.au
to view video tutorials.