PSA LIFESAVER LIFWMB2 User manual

1
1
2
0
8
-
7
2
0
4
-
0
0
Quick Start Guide
LIFWMB2 Interlink Network Setup
Please Read All Instructions First!

2
Section 1
Quick Start RF Interlink Network Setup
Section 2
Adding a Device to an Existing
RF Interlink Network
Section 3
Resetting a Device
1
Power Up ONE Device
Connect one smoke alarm to
the LIFWMB2 RF baseplate.
Baseplate LINK button Red LED will
ash on/o every second.
LINK button

3
Section 1
Quick Start RF Interlink Network Setup
Section 2
Adding a Device to an Existing
RF Interlink Network
Section 3
Resetting a Device
1
Power Up ONE Device
Connect one smoke alarm to
the LIFWMB2 RF baseplate.
Baseplate LINK button Red LED will
ash on/o every second.
LINK button

4
Push the LINK button two times on
the rst powered device.
2 Red LED ashes every 2 seconds .
This is the network coordinator.
Join Mode is open.
Push button twice
2
On the First Powered Device

5
Push the LINK button two times on
the rst powered device.
2 Red LED ashes every 2 seconds .
This is the network coordinator.
Join Mode is open.
Push button twice
2
On the First Powered Device
3
Power up Remaining Devices
Power up all of the remaining RF baseplates
by connecting them completely
on the smoke alarm.
Red LED ashes 3 times
every 2 seconds after
joining the network.

6
Push the LINK button twice on any unit
after all the smoke alarms have joined
the network.
Red LED stops ashing on each unit
as network is closed.
4
Pick Any Device
Push button twice

7
5
If all devices are no longer ashing the
Red LED, the devices are now connected.
Congratulations!
Setup Complete!
Refer to user guide for detailed
installation instructions.

8
Section 2
Adding a Device
to an Existing RF Interlink Network
To open the RF Interlink Network,
push the LINK button twice on any
previously connected smoke alarm
Red LED ashes every 2 seconds.
Join Mode is open.
1
Push LINK Button Twice on
any installed unit.
Push button twice

9
To open the RF Interlink Network,
push the LINK button twice on any
previously connected smoke alarm
Red LED ashes every 2 seconds.
Join Mode is open.
1
Push LINK Button Twice on
any installed unit.
Push button twice

10
2
Power On the New Device(s)
Connect the smoke alarm to the
new RF baseplate.
Red LED ashes 3 times every 2 seconds
after joining the network.
Push LINK button twice on any connected
device to close the network.
Red LED stops ashing on
each unit as network is closed.
Push button twice
3
Choose ANY Connected Device

11
Push LINK button twice on any connected
device to close the network.
Red LED stops ashing on
each unit as network is closed.
Push button twice
3
Choose ANY Connected Device

12
4
If all devices are no longer ashing the
Red LED, the devices are now connected.
Congratulations!
Setup Complete!
Refer to user guide for detailed
installation instructions.

13
Section 3
If you encounter an issue at any point
during the RF Interlink network setup process,
or if you need to remove a device from a network,
you may reset the device by following
the subsequent directions.
Resetting Your Device

14
Push LINK button twice to open Join Mode.
Unit will respond with 2 or 3 ashes,
indicating Coordinator or RFD respectively.
1
Resetting the Device
Push button twice

15
Press and Hold button for 4 to 5 seconds.
Unit will respond with 4 quick ashes
indicating that the wireless settings
have been reset and the unit is now
a standalone alarm.
Device has been put in General Reset Condition.
See User Guide for complete instructions
on how to return to a network
Push and hold button
2
Resetting the Device

16
Need more help
getting started?
Consult the User Guide for more detailed
instructions on product installation and use.
Visit www.psaproducts.com.au
to view video tutorials.