PSS LANEGARD3 User manual

CONTACT:
Call 800.662.6338 to talk to a Customer Service Representative.
HOURS:
8 AM to 5 PM (E.T.)
Monday through Friday
ASSEMBLY INSTRUCTIONS
FOLDING TYPE III BARRICADE
LANEGARD3™
FHWA LETTER:
Letter: WZ-336
Tested to Manual for Assessing Safety Hardware
(MASH) Test Level: 3

2LaneGard3 Assembly Instructions
LANEGARD3™COMPONENTS
TABLE OF CONTENTS
PAGE
03
PAGE
07
PAGE
05
UPRIGHT
ASSEMBLY
FOLDING OF
LANEGARD3
BOARD
ATTACHMENT
1.
2.
3.
1.Wave Centerboard* - Quantity 3
2. Cross-Bars - Quantity 2
3.Upright Assembly - Quantity 2
4. Anti-Skid Feet - Quantity 4 (Enlarged to show detail)
5. 1/4-20 x 1.5” Hex-Bolts - Quantity 4 (Enlarged to show detail)
6.Flat Washer - Quantity 16 (Enlarged to show detail)
7. Lock Nut - Quantity 4 (Enlarged to show detail)
8. 1/4-20 x 2” Hex-Bolts - Quantity 12 (Enlarged to show detail)
9. Pallet Nut - Quantity 12 (Enlarged to show detail)
*Visit PSS-Innovations.com to view retroreflective sheeting options
4.
5.7.6.
8.6.9.
Hardware for cross bar attachment
Hardware for board attachment

STEP 1
3LaneGard3 Assembly Instructions
Lay out Upright Assembly (3), Cross-Bars (2), and Rubber Feet (4), on a flat, clean surface. Attach optional Rubber Feet (2 per cross-bar)
prior to assembly. Slide the Rubber feet onto the Cross-Bars so that the bolt hole is accessible.
TOOLS REQUIRED - 1/4” HEX KEY, 7/16” WRENCH
2.
4.
3.
3.
LANEGARD3™ASSEMBLY INSTRUCTIONS
LANEGARD 3
ASSEMBLY

LaneGard3 Assembly Instructions 4
2.
Connect the two ends of the Cross-Bars (2) to the front and back legs using 1/4-20 x 1.5” bolts (5), washers (6) and lock nuts (7).
Make sure base hardware hex-bolt fits into hex pocket on the upright, depicted in the lower right image above. Move the Rubber feet
(4) outward onto the Upright Assembly (3). Be sure that the feet can still maintain full contact with the ground and are far enough
out to maximize stability.
Repeat steps 1-2 on the three other crossbar connection points on the Upright Assembly (3).
STEP 2
STEP 3
3.
7.
6.
5.
4.
LANEGARD3™ASSEMBLY INSTRUCTIONS

To unfold LaneGard 3: Stand assembled unit up. Push the upper cross bar (2) away from you with your foot. Open the legs completely until
the back leg lock in the open position. This step must be completed before attaching the Wave Centerboards as it will assist with proper
installation. NOTE: The leg that was pushed away is now the back leg and the leg that moved toward the operator is now the front leg.
Attach boards to front side of Upright Assembly (3). Be sure that the orientation of the centerboard matches the orientation of the sheeting
installed. Attach bottom board first; start with top hole on Upright for each board. Install boards using Pallet Nuts (9), washers (6), and 1/4-20
x 2” bolts (8). Insert hex head bolt and washer through Upright and centerboard into the Pallet Nut. Repeat for the remaining boards. Keep
Pallet Nut from turning by using the 1/4” hex key. Tighten bolts with rachet until snug.
STEP 4
STEP 5
LANEGARD3™ASSEMBLY INSTRUCTIONS
6.
8.
1.
1.
9.
2.
A.
B.
C.
3.
3.
5LaneGard3 Assembly Instructions
Front side
Front side
Back side

LaneGard3 Assembly Instructions 6
Repeat the previous step for the three other conncetion points on the Wave centerboard and the upright.
Repeat steps 5-6 on the two remaining boards. To fold for transport and storage: flex the back legs (3) inward,
pull the upper section of the back legs inward, and upward, as
shown below, then fold the device. This disengagues the legs’
mechanical locking mechanism and enables the leg to fold.
Failure to flex the legs inward may result in damage to LaneGard3.
STEP 6
STEP 7 STEP 8
LANEGARD3™ASSEMBLY INSTRUCTIONS
A.

We are a proud member of:
PSS |2444 Baldwin Road, Cleveland, OH 44104 |800.662.6338 |PSS-Innovations.com |Copyright © 2023 02/23
Follow us on:
CONTACT:
Call 800.662.6338 to talk to a Customer Service Representative.
HOURS:
8 AM to 5 PM (E.T.)
Monday through Friday