SINGLE PAGE INSERT
5 2
7. Only use this Hydraulic press on a surface that is stable, level, dry and not
slippery, and capable of sustaining the load. Keep the surface clean, tidy and
free from unrelated materials and ensure that there is adequate lighting.
8. Inspect the press before each use. DO NOT use if bent, broken, cracked,
leaking or otherwise damaged, any suspect parts are noted or it has been
subjected to a shock load.
9. Checktoensurethatallapplicableboltsandnutsarermlytightened.
10. Ensure that workpiece is center-loaded and secure.
11. Keep hands and feet away from bed area at all times.
12. DO NOT use the press to compress springs or any other items that could
disengage and cause a potential hazard. Never stand directly in front of
loaded press and never leave loaded press unattended.
13. DO NOT operate the hydraulic press when you are tired or under the
inuenceofalcohol,drugsoranyintoxicatingmedication.
14. When work is done, stop pumping the handle, slowly and carefully remove
load from work piece by turning the release valve counter clockwise in small
increments.
15. The hydraulic press will not operate safely without proper lubrication. Using
the press without proper lubrication will result in poor performance and
damage to the press.
16. DONOTmakeanymodicationstothepress.
17. DONOTusebrakeuidoranyotherimproperuidandavoidmixing
different types of oil when adding hydraulic oil. Only good quality hydraulic
jack oil should be used.
18. DONOTexposethehydraulicpresstorainoranyotheroutdoorweather
or elements. Lubricate all parts before and after use to ensure the hydraulic
press stays in good working condition from rust or corrosion.
19. If the press needs repairing and/or there is any part that needs to be
replaced, have it repaired by authorized technicians and only use the
replacement parts supplied by the manufacturer.
WARNING: THE WARNINGS, CAUTIONS AND INSTRUCTIONS
DISCUSSED IN THIS INSTRUCTION MANUAL CANNOT COVER ALL
POSSIBLE CONDITIONS AND SITUATIONS THAT MAY OCCUR. IT MUST
BE UNDERSTOOD BY THE OPERATOR THAT COMMON SENSE AND
CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS
PRODUCT, BUT MUST BE SUPPLIED BY THE OPERATOR.
OPERATING INSTRUCTIONS
1. Place the heel block on press bed frame, then insert workpiece onto the heel block.
2. Close the release valve by turning it clockwise until it is rmly closed.
3. Pump the handle until serrated saddle nears workpiece.
4. Align workpiece and ram to ensure center-loading.
5. Pump the handle to apply load onto workpiece.
6. When work is done, stop pumping the handle, slowly and carefully remove load
from workpiece by turning the release valve counterclockwise in small increments.
7. Once ram has fully retracted, remove workpiece from bed frame.
1. Clean the outside of the press with dry, clean and soft cloth and periodically
lubricate the joints and all moving parts with a light oil as needed.
2. When not in use, store the press in a dry location with ram and piston fully
retracted.
3. Whenpressefciencydrops,purgethehydraulicsystemtoeliminateanyair
in the system.
4. Checkthehydraulicoil:Removetheoilllernutonthepump,ifitisnot
adequate,llwithhighqualityhydraulicjackoilasnecessary,thenreplacethe
oilllernut,purgeawayairfromthehydraulicsystem.
CARE & MAINTENANCE
RAM EXPANDED PARTS LIST
1 Cover ..................................1
2 Circlip..................................1
3 Piston Rod ..........................1
4 Circlip..................................1
5 Bushing...............................1
6 Nylon Ring ..........................1
7 Sealing Ring........................1
8 Circlip..................................1
9 Nut ......................................1
10 Spring .................................1
11 Screw..................................1
12 Protection Cup....................1
13 Ring.....................................1
14 Cylinder...............................1
15 Screw..................................1
16 Coupling Ring .....................1
17 Coupling Ring .....................1
18 O-ring..................................1
19 Dust Cap.............................1
No. Description Qty.
