PUK Hydrotech Medium Square LED 401006 User manual

ASSEMBLY AND OPERATING INSTRUCTIONS:
HYDROTECH MEDIUM O2 SQUARE LED
-Power consumption : 2X8W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K or 4000K
-Lens ype : 10° 30° 45°
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
Made in Italy
COD. 401006
COD. 401018
COD. 401014
COD.401019
COD. 401006
-replace the damaged protective glass
-glass features: plane float glass - safety tempered
-getting rid of as urban waste forbidden
-separate collection is mandatory when the product is at the
end of its life
- -Class I fitting electric gruonding is needed
-Complete protection from dust and water jets
IP65
NB: These assembly instructions must be given to end users for correct maintenance and so that they know how to change the bulb.
The a liance must not be tam ered with or transformed and it must be installed and used as su lied and in com liance with the
National Rules on Installations. Any non-com liant installations will invalidate all forms of guarantee. The com any cannot be held
res onsible for damage caused by incorrect assembly.
IK 07
HYDROTECH MEDIUM O2 SQUARE PRO LED
-Power consumption : 2X14W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K
-Lens ype : 10° 30° 45°
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
COD. 401018
HYDROTECH MEDIUM O1 SQUARE LED
-Power consumption : 8W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K or 4000K
-Lens ype : 10° 30° 45°
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
COD. 401014
HYDROTECH MEDIUM O1 SQUARE PRO LED
-Power consumption : 14W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K
-Lens ype : 10° 30° 45°
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
COD. 401019

Recommendations
1) verify that the equipment used to connect our devices to enjoy
all the guarantees required under uropean law;
2) use the cables, connectors and quality materials for electrical wiring;
3) Products with IP65/68 degree make the wiring / connections with accessories
provide the same degree IP of the selected product (available in the catalog);
4) In the case of installations outside is not recommended to install the power supplies in the
formwork and / or in the junction box without adequate protection
Choice of installation location
The unit should be positioned so that when in use is not subject to direct radiation from the sun or other heat sources . High tempera-
tures reduce the life and efficiency of the components or the L D module .
Relam ing and maintenance:
-The relamping must be done with maximum attention avoiding to dirty the sealing gasket and its contact surface. It is therefore
necessary before
opening the fixture to carefully wipe the floodlight then unscrew the round frame by the proper key
-If the gasket is damaged, deformed or not in erfect conditions it is necessary to change it
-it is essential to do a frequent cleaning of the glass and of the outer surface of the fixture to avoid build up of mud and dirtiness
resulting in dangerous
overheating due to uncorrect light and heat dissipation. Clean carefully the glass screen removing limestone deposits by means of a
scraper.
.The re lacement must be done by a qualified electrician.
INSTALLATION:
-SWITCH-OFF THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE OPERATION
-1 Prepare holes in the wall using plugs type ficher (not included in the package), insert the cable through the rubber cable gland
and then fix the plate
-2 Tighten the plugs screws
-3 Unscrew 2 screws of inner plate
-4 Make the electrical connection to the terminal
-5 refit the plate to the luminaire body (2 screws) and then place the luminaire to wall plate, fully tighten 4 grain screws
LAMP BAS FIXATION HOL S DIM NSIONS