PUK 803001 User manual

ASSEMBLY AND OPERATING INSTRUCTIONS:
ASSEMBLY AND OPERATING INSTRUCTIONS:ASSEMBLY AND OPERATING INSTRUCTIONS:
ASSEMBLY AND OPERATING INSTRUCTIONS:
HYDROBOOK POLE-TOP MAXI 12LED
-Power consumption : 18W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K WARM WHI E
or other available 4000K or Blue
-Beam angle : cycle route pedestrian
(narrow) or street (medium wide)
-Lumen output : 1728
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
Made in Italy
COD. 803001
COD. 803001COD. 803001
COD. 803001
COD. 803002
COD. 803002COD. 803002
COD. 803002
-replace the damaged protective glass
-sostituire i vetri di protezione se danneggiati
-glass features: plane float glass - safety tempered
-caratteristiche vetro: vetro piano float di sicurezza temperato
-getting rid of as urban waste forbidden
-separate collection is mandatory when the product is at the end of its life
-è vietato lo smaltimento come rifiuto urbano
-è obbligatoria la raccolta separata a fine vita del prodotto
-class I luminaire with built-in transformer 220-240V 50-60Hz
-apparecchio in classe 1 con trasformatore incorporato a 220-240V
50-60Hz
-totally dust-proof , protected against the water
- totalmente protetto contro la polvere , e ail’acqua
IP65
NB: These assembly instructions must be given to end users for correct maintenance and so that they know how to change the bulb.
The appliance must not be tampered with or transformed and it must be installed and used as supplied and in compliance with the
National Rules on Installations. Any non-compliant installations will invalidate all forms of guarantee. The company cannot be held
responsible for damage caused by incorrect assembly.
HYDROBOOK POLE-TOP MAXI 24 LED
-Power consumption : 36W
-Voltage :220-240V 50-60Hz
-Color emperature : 3000K WARM WHI E or
other available 4000K or Blue
-Beam angle : cycle route pedestrian (narrow)
or street (medium wide)
-Lumen output : 3456
-Insulation class: I
-IP protection: IP65
-Gross weight: 3kg
COD. 803001
COD. 803001COD. 803001
COD. 803001
COD. 803002
COD. 803002COD. 803002
COD. 803002
BURIED POLES
BURIED POLESBURIED POLES
BURIED POLES
POLES WITH BASE
POLES WITH BASEPOLES WITH BASE
POLES WITH BASE-PLATE
PLATEPLATE
PLATE












 

 


Installation:
CAUTION: Possibly hazardous optical radiation emitted from this product Do not stare at operating lamp May be harmful to the eye The
replacement must be done by a qualified electrician
Recommendations
1) verify that the equipment used to connect our devices to enjoy all the guarantees required under European law
2) use the cables, connectors and quality materials for electrical wiring
3) Products with IP65/68 degree make the wiring / connections with accessories provide the same degree IP of the selected product
(available in the catalog)
4)Disconnect main voltage during installation and maintenance
5)It is essential to do a frequent cleaning of the glass and of the outer surface of the fixture to avoid build up of mud and dirtiness resul-
ting in dangerous overheating due to uncorrect light and heat dissipation. Clean carefully the glass screen removing limestone deposits
by means of a scraper.
Disconnect main voltage during installation and maintenance
1)Drill hole on the edge of the pole suitable at the point of supply 25mm to the top (pic1)
2) Remove the bracket of the luminaire unscrewing the two lateral screw by using an hexagonal tool (pic 2)
3) Assembling the semicircular adapter to the bracket as shown in figure (pic 3)
4) Plug the adapter with the bracket to the pole (pic4)
5) Fix the adapter with the bracket to the pole in the hole previously drilled using the hex key (pic5)
6) Plug the power cable through the hole of the bracket and the pole (pic6)
7) Fix the luminaire to the bracket
8) Adjust the vertical and horizontal inclination using the hexagonal screw drive by acting on the screws of the brackets (pic8)
9) For poles with 60 mm in diameter using the plastic adapter as in picture 9
10) For electrical connection of the pole connectors follow the general safety rules. Is a Class 1 should be connected to the grounding
device
