Pulsar PSC12010 User manual

1
PSC12010 12V/1A/55MM
switch mode power supply
PSC12010
EN
Edition: 1st from 17.12.2010
Supercedes edition: ___________
1. Tech ical descriptio .
1.1. Ge eral descriptio .
Stabilised DC power supply is intended for cameras installed in CCT industrial systems.
Power supply cam be assembled in intalations box or fitted with 3mm screws. The unit is protected against short-
circuit and overload.
1.2. Tech ical parameters.
Dime sio s (L x W x H) 50 x 48 x 25 mm
Net/Gross weight 0,095 kg/0,125kg
230V AC Cable le gth 120mm
DC Cable le gth 90mm
Assembly 2x screws 3mm
Supply voltage 100 ÷ 240 AC 50/60 Hz
Output power 12W
MAX
Output voltage 12 DC
Maximum output curre t
for ta<30°C
1000mA*
Maximum output curre t
for ta=40°C
700mA*
Short circuit protectio SCP / overload
protectio OLP
Yes
Operatio status i dicatio No
Operatio co ditio s
0
o
C ÷ 40
o
C , relative humidity 10 ÷ 90 %,
* - output current of the power supply unit depending on ambient temperature. For temperature above 30°C maximum
output current is limited according to graph 1. The power supply operation life time is limited by reliability of the
electrolyte capacitors which strongly depends of an operation temperature. Avoid excessive temperature rise of the
power supply!
Graph 1 Relatio betwee output curre t a d ambie t temperature.
2. I stallatio .
2.1. Requireme ts.
The adapter shall be mounted by the qualified installer having appropriate (required and necessary for a
given country) permissions and qualifications for connecting (operating) low-voltage installations. The unit shall be

2
mounted in closed rooms, according to the environment class II, of the normal air humidity (RH=90% max. without
condensation) and the temperature within the range from 0°C to +40°C.
The adapter shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill L D and
EMC requirements the rules for power-supply, encasing and shielding shall be observed according to application.
2.2. I stallatio procedure.
2.2.1. Fit power supply inside the box or other device
2.2.2. Connect the DC output to the load or to the terminal block
2.2.3. Connect the power supply unit to the AC line.
2.2.3. After tests and operation control are performed, close installation box, case etc.and switch on
the power (230 AC)
3. Mai te a ce.
The adapter does not require any specific maintenance procedures, however, in the case of significant
level of dust, it should be cleaned with the compressed air.
WEEE designation
The waste electric and electronic equipment worn out may not be disposed of
together with standard household waste. According to the WEEE directive,
applicable in the EU, the separate neutralization methods should be used for
electric and electronic equipment.
Pulsar K.Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: biur[email protected], sa[email protected]l
http:// www.pulsar.pl
THE GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz, Particular Partnership (the manufacturer) provides a one-year quality arranty for devices, as from the purchase date placed on a purchase proof.
2. The arranty includes free repair or replace for a functional equivalent (the selection is performed by the manufacturer) of a non-operational device due to reasons
dependent on the manufacturer, including production and material defects, as far as defects are notified ithin the arranty period (item 1 and 2).
3. The equipment subject to arranty shall be provided to the point, here it has been purchased or directly to the place of business.
4. The complete devices are subject to arranty, and the sort of defect shall be described in ritten in a correctly fulfilled claim notification.
5. If a claim is accepted, the manufacturer is obliged to perform arranty repairs as soon as possible, but no later than 14 orking days since the device is provided to the
service of the manufacturer.
6. The repair period specified in item 5 can be extended, if there are no technical opportunities to perform the repair or the equipment is conditionally accepted by the
service due to non-compliance of the arranty conditions by the person lodging a claim.
7. All service actions related to arranty are performed exclusively at the service of the manufacturer.
8. The arranty does not include the follo ing defects of the device due to:
- manufacturer-independent reasons,
- mechanical defects,
- improper storage and transport,
- operation contrary to the instruction manual or purpose of the device,
- emergencies, including atmospheric discharges, failures of the po er net ork, fire, flood, effect of high temperature and chemical agents,
- improper installation and configuration (contrary to the instruction manual)
9. The loss of rights resulting from the arranty al ays occurs, if it is confirmed that construction changes have been performed or repairs have not been performed at the
service of the manufacturer, or if serial numbers or arranty labels of the device are someho replaced or damaged.
10. The responsibility of the manufacturer to ards the purchaser is limited to the value of the device determined according to the holesale price from the purchase day
suggested by the manufacturer.
11. The manufacturer does not bear any responsibility for damages resulting from failure, faulty operation or inability to use the device, particularly if it results from non-
compliance ith advices and requirements included in the instruction manual or contrary to purpose of the device.