Pulsar ISFG42 User manual

1
ISFG42
v1.0
Industrial switch ISFG42 (2xPoE, 2xSFP)
Edition: 2 from 26.08.2020
Supercedes the edition: 1 from 16.01.2020
EN
Features:
4 ports industrial switch
2 PoE ports 10/100/1000 Mb/s, (1÷2 ports) (data and power
supply)
2 ports 100/1000 Mb/s SFP
30 W for each PoE port, supports devices complaint with the
IEEE802.3af/at (PoE+) standard
Supports auto-learning and auto-aging of MAC
addresses (8K size)
Possibility of redundant power supply
Mounting on a DIN rail (TH35)
LED indication
warranty –2 year from the production date
Example of use
1. Technical description
1.1. General description.
ISFG42 is a 4-ports PoE switch designed to supply IP cameras operating in IEEE 802.3af/at standard.
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 –2 ports of the switch.
UP LINK ports (marked 3 and 4) are used to connect further network devices using fiber optics (using SFP modules - GBIC).
On front panel there is LEDs signaling of the device's status (description in table below). Device has solutions that allow it to be
powered from two sources (emergency power supply, redundant power supply) –in case of a failure of one source,
it immediately switches to backup one.
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access
point or router.

2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3 Description of components and connectors.
Table 1. (See Fig. 2)
Component No.
(Fig. 2)
Description
[1]
2 x PoE ports (1÷4)
[2]
2 x UP LINK ports (SFP)
[3]
Power Socket (V1/V2)
[4]
Holder for DIN rail
Fig. 2. The view of the switch.

3
1.4 Technical parameters
Table 2.
Ports
2 ports 10/100/1000 Mb/s (PoE)
2 ports 100/1000 Mb/s (UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802. 3af/at (1÷2 ports), 52 V DC / 30 W at each port *
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
12 Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
Power supply
Switch: 12-57 V DC; 1,2 A max.
PoE: 48-57 V DC; 1,2 A max.
Self-power consumption
5 W max.
Operating conditions
temperature -30°C ÷ 70°C,
relative humidity 5% - 90%, no condensation
Dimensions
W=30, H=128, H1=10, D=112, D1=8 [+/- 2 mm]
Gross/Net weight
0,3 / 0,4kg
Protection class
EN 60950-1:2007
I (first)
Storage temperature
-30°C ÷ 70°C
Declarations
CE
*The given value of 30 W per port is the maximum value. The total power consumption should not exceed 60 W.
2. Installation
2.1. Requirements
The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative
humidity (RH=90% maximum, without condensation) and temperature from -30°C to +70°C. Ensure the free flow of air around
the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the
enclosure.
The switch load balance should be done before installation. Depending on application, appropriate power supply should
be selected, PoE available only at 48-57 V (52 V recommended). The given value of 30 W per port is the maximum value
referring to a single output. The total power consumption should not exceed 60 W. The increased demand for power is
particularly evident in the case of cameras with heaters or infrared illuminators - when launching these features, the power
consumption increases rapidly, which may adversely affect the operation of the switch. As the device is designed for a
continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection in the power supply
circuit should be provided. The electrical system shall be made in accordance with applicable standards and regulations.
2.2. Installation procedure
1. Connect switch to power supply unit(s), paying attention to polarization and other parameters.
2. Connect the power supply(s) to the 230 V socket.
3. Connect the camera wires to the RJ45 connectors (sockets RJ45).
4. Check the optical indication of switch operation (see Table 3).

4
Connection schemes:

5
3. Operation indication.
Table 3. Operation indication
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
GREEN LED LIGHT (Power)
Indication of the switch's power
supply
OFF –no power supply of the switch
ON –power supply on, normal operation
OPTICAL INDICATION AT THE PoE PORTS (1÷2)
GREEN LED LIGHT (PoE)
Indication of the PoE power supply
at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant with
the IEEE802.3af/at standard)
ON –power supply at the RJ45 port
Blinking –short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices 10/100Mb/s
and data transmission
OFF- no connection
ON - the device is connected 10/100Mb/s
Blinking –data transmission
OPTICAL INDICATION AT THE UP LINK PORTS
GREEN LED LIGHT (3)
The connection status of LAN
devices and data transmission
OFF- the device no connection
ON - the device is connected
Blinking –data transmission
GREEN LED LIGHT (4)
The connection status of LAN
devices and data transmission
OFF- the device no connection
ON - the device is connected
Blinking –data transmission
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment should be
disposed of separately from normal household waste .
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl