Pulsar S108-B User manual

1
S108-B
v1.1
S108-B 10-ports switch with buffer power supply
for 8 IP cameras
PL
Edition: 3 from 14.02.2019
Supercedes the edition: 2 from 16.04.2018 EN**
Features:
Uninterruptible power supply of 8 IP cameras (52 V DC)
Switch 10 ports
8 PoE ports 10/100Mb/s, (data and power supply)
2 ports 10/100Mb/s (UpLink)
30 W for each PoE port, supports devices complaint with
the IEEE802.3af/at (PoE+) standard
Approximate backup time: 5h 30min
LED indication
Metal enclosure –color white RAL 9003
with space for two 17 Ah/12 V battery
Supports auto-learning and auto-aging of
MAC addresses (1K size)
warranty –2 year from the production date
Example of use.
CONTENTS
1. Technical description.
1.1 General description
1.2 Block diagram
1.3 Description of components and connectors
1.4 Technical parameters
2. Installation.
2.1 Requirements
2.2 Installation procedure
3. Indication of the device operation
3.1 LED indication of operating status
3.2 Optical indication of the switch operation
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on)
4.2 Disconnection of discharged battery
4.3 Maintenance

2
1. Technical description
1.1. General description.
The S108-B is dedicated for uninterruptible power supply of 8 IP cameras (52 V DC power supply).
The main elements of this system include:
- 10 ports PoE switch
- 27,6 V (PSB-1552455) buffer power supply with two 17 Ah / 12V batteries
- a converter (DC/DC52230) increasing the voltage to 52 V DC (supply of the PoE switch)
In case of power decay, a battery back-up is activated immediately.
The approximate backup time is given assuming that all output ports are used (using typical devices and 17 Ah
batteries). The electricity consumption for own needs and the energy efficiency of the power intake track were taken into
account. The exact description of how to perform the calculations can be found at: "Approximate backup time - assumptions for
calculations".
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 - 8 ports of the switch.
The Up Link ports is used for connection of another network device e.g. recorder. The LEDs at the front panel indicate the
operation status (description in the table. 8).
The switch is housed in a metal enclosure (color RAL 9003) which can accommodate a two 17 Ah/12 V batteries. The enclosure
features a micro switch tamper indicating door opening (front panel). The S108-B is fitted with two LEDs on the front panel
(Red LED - indicates the presence of 230 V supply voltage, green LED indicates the presence of DC voltage).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless
access point or router.
1.2 Block diagram.
Fig. 1. Block diagram.

3
1.3 Description of components and connectors.
Fig. 2. The enclosure view.
Table 1. (See Fig. 2)
Component No.
(Fig. 2)
Description
[1]
Switch PoE
[2]
Switch mode buffer power supply unit
[3]
DC/DC52230 converter
[4]
Output filter
[5]
Tamper –micro switch (terminals) of tamper protection (NC)
[6]
Battery space for two (2 x 17 Ah/12 V - connect the batteries in series)
[7]
Power supply connector of the PSU –L, N
PE protective connector (electric shock)
[8]
BAT +, BAT - battery output + BAT red, - BAT black

4
Fig. 3. The view of the switch.
Table 2. (See Fig.3)
Component No
(Fig. 3)
Description
[1]
8 x PoE ports (1÷8)
[2]
2 x UPLINK port
[3]
52 V DC power supply socket
1.4 Technical parameters
- parameters of the switch (tab.3)
- electrical parameters (tab.4)
- mechanical parameters (tab.5)
- operation safety (tab.6)
- operating parameters (tab.7)
Table 3. Parameters of the switch
Ports
10 ports 10/100Mb/s (8 x PoE + 2 x UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af/at (1÷8 ports), 52 V DC / 30 W at each port *
Used pairs 1/2 (+), 3/6 (-)
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
1,6Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
*The given value of 30 W per port is the maximum value. The total power consumption should not exceed 96 W.
Table 4. Electrical parameters
Mains supply
~200-240 V; 50 Hz
Current up to
1 A
Supply power
110 W
Output current at the PoE ports (RJ45)
8 x 0,6 A ΣI=2 A (max.)
Output voltage at the PoE ports (RJ45)
52 V DC
Short-circuit protection SCP and overload protection OLP
105% ÷ 150% PSU power, automatic recovery
(the fault requires disconnection of the DC output circuit)
PSU current consumption
250m A/27,6 V DC
Battery charge current
0,5 A max. /2x17 Ah (+/-5%)
Approximate backup time
5h 30min
Battery circuit protection SCP and reverse
polarity connection
melting fuse
Deep discharge battery protection UVP
U<19V (± 5%) – disconnection of the batteries
Sabotage protection:
- TAMPER output indicating enclosure opening
- microswitch, NC contacts (enclosure closed),
0,5 A@50 V DC (max.)

5
Table 5. Mechanical parameters
Dimensions
W=397, H=350, D+D1=92+8 [+/- 2mm]
W1=402, H1=355 [+/- 2mm]
The dimensions of the
battery compartment
370 x 180 x 80mm (WxHxD) max
Gross/Net weight
4,8 / 5,1 kg
Enclosure
Steel plate, DC01 1,0mm color white RAL 9003
Closing
Cheese head screw x 2 (at the front), (lock assembly possible)
Connectors
Power supply of the cameras: RJ45 socket
230 V AC input: Φ0,63-2,50 (AWG 22-10),
Battery output BAT: 6,3F-2,5
TAMPER output: wires
Notes
The enclosure does not touch the assembly surface so that cables can be led.
Table 6. Operation safety
Protection class EN 609501:2007
I (first)
Protection grade EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU
- between input circuit and protection circuit
- between output circuit and protection circuit
3000 V AC min.
1500 V AC min.
500 V AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V DC
Declarations
CE
Table 7. Operating parameters
Operating temperature
-10ºC...+40ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
2. Installation
2.1. Requirements
The device should be mounted by a qualified installer, holding relevant permits and licenses (applicable and required for
a given country) for 230 V and low-voltage installations. It is required to install an installation switch with a nominal
current of min. 3 A in the power supply circuits outside the power supply unit.
The device shall be mounted in confined spaces, according to the environment class II, with normal air humidity
(RH=90% max. without condensation) and the temperature from -10°C to +40°C.
The switch shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of
the enclosure.
Before installation, prepare a Switch'a load balance.
The given value of 30 W per port is the maximum value referring to a single output. The total power
consumption should not exceed 96 W. The increased demand for power is particularly evident in the case of cameras
with heaters or infrared illuminators - when launching these features, the power consumption increases rapidly, which
may adversely affect the operation of the switch. As the device is designed for a continuous operation and is not
equipped with a power-switch, therefore an appropriate overload protection shall be guaranteed in the power supply
circuit. Moreover, the user shall be informed about the method of unplugging (usually through assigning an appropriate
fuse in the fuse-box). The electrical system shall follow valid standards and regulations.

6
2.2. Installation procedure
Before installation, cut off the voltage in the 230 V power-supply circuit.
To switch power off, use an external switch, in which the distance between the contacts of all
poles in the disconnection state is not less than 3mm.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (230 V) to L-N clips of the PSU.
The shock protection circuit shall be performed with a particular care, i.e. the yellow and green wire
coat of the power cable shall stick of the terminal - marked with ‘ ‘symbol on the PSU enclosure.
Operation of the PSU without the properly made and fully operational shock protection circuit is
UNACCEPTABLE! It can cause a device failure or an electric shock.
4. Connect the ground wire to the terminal marked with the symbol (power supply module connector). Use a
three-core cable (with a yellow and green protection wire) to make the connection. Lead the cables to the
appropriate clips through the insulating bushing of the connection board.
5. Connect the power (230 V).
6. Connect the battery (mind the colours):
- battery output (+V): BAT+ cable / red,
- battery output (0V): BAT –cable / GND / black.
7. Connect the camera cables to the RJ45 connectors (PoE connectors) and connect the recorder to the network
(the UPLINK connector).
8. Check the optical indication of the switch operation.
9. After installing and checking proper working, the enclosure can be closed.
Connection schemes

7
3. Indication of the device operation.
3.1 LED indication of operating status.
The PSU is equipped with two diodes on the front panel:
RED LED:
on –the PSU is supplied with 230 V
off –no 230 V supply
GREEN LED:
on –DC voltage in the AUX output of the PSU
off –no DC voltage in the AUX output of the PSU
3.2 Optical indication of the switch operation (see Table 8).
Table 8. Indication of the switch operation
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY (1÷8)
GREEN LED LIGHT (PoE)
Indication of the PoE power
supply at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant
with the IEEE802.3af/at standard)
ON –supply at the RJ45 port
Blinking –short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10/100 Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10/100 Mb/s
Blinking –data transmission
OPTICAL INDICATION AT THE UPLINK PORTS
GREEN LED LIGHT
Applies only to the right side port:
No light (OFF) - No supply voltage of the switch
ON - the switch is powered, correct operation
YELLOW LED LIGHT (LINK)
The connection status of
LAN devices, 10/100 Mb/s
and data transmission
OFF- no data transmission
ON - the device is connected 10/100Mb/s
Blinking –data transmission

8
Installation example of the S108-B battery
(Battery not included)
4. Operation and use.
4.1 Overload or short circuit of the PSU output (SCP on).
In case of overload, the output voltage is automatically shut off, and so is the LED indicator. The restoration of the voltage
takes place immediately after the failure (overload) is over.
4.2 Disconnection of discharged battery.
The PSU is equipped with the discharged battery disconnection system. During the battery-assisted operation, reducing
voltage below 9,5 V at the battery terminals will cause battery disconnection.
4.3 Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the power supply
network. The PSU does not require performing any specific maintenance measures, however, in case of significant dust rate,
its interior is recommended to be cleaned with compressed air. In case of fuse replacement, use a replacement of the same
parameters.
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment should be
disposed of separately from normal household waste .
The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but recycled according to the
applicable law.
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl