Pulsar S64-C User manual

1
S64-C
v1.2
S64-C 6-ports switch for 4 IP cameras
in the enclosure
PL
Edition: 3 from 14.02.2019
Supercedes the edition: 2 from 01.03.2018 EN
Features:
Switch 6 ports 10/100Mb/s
4 PoE ports 10/100Mb/s (data and power supply)
2 ports 10/100Mb/s (UP LINK)
30 W for each PoE port, supports devices complaint
with the IEEE802.3af/at (PoE+) standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
LED indication
Metal enclosure –color white RAL 9003
warranty –2 year from the production date
Example of use.
1. Technical description
1.1. General description.
The S64-C is a complete kit to build the CCTV system based on IP cameras. The switch and power supply unit are
housed in a metal enclosure.
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 –4 ports of the switch. The
UP LINK ports is used for connection of another network device via RJ45 connector. The LEDs at the front panel indicate the
operation status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access
point or router.

2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3 Description of components and connectors.
Table 1. (See Fig. 2)
Component No.
(Fig. 2)
Description
[1]
Switch
[2]
Switch mode buffer power supply unit (PS-604812), 52 V DC/60 W
[3]
Potentiometer adjusting the output voltage of the power supply (48÷53 V)
[4]
LED light –power supply operation indication
[5]
T 6,3 A / 250 V fuse socket
[6]
Holders for mounting cable
Fig. 2. The enclosure view.

3
Table 2. (See Fig. 3)
Component No
(Fig. 3)
Description
[1]
2 x UP LINK port
[2]
4 x PoE ports (1÷4)
[3]
52 V DC power supply socket
Fig. 3. The view of the switch.
1.4 Technical parameters (tab.3)
Table 3.
Ports
6 ports 10/100Mb/s (4 x PoE + 2 x UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross
PoE power supply
IEEE 802. 3af/at (1÷4 ports), 52 V DC / 30 W at each port *
Used pairs 1/2 (+), 3/6 (-)
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
1,6Gbps
Transmission method
Store-and-Forward
Optical indication of operation
Switch power supply;
Link/Act;
PoE Status
Mains supply
~200-240 V; 50Hz; 0,6 A
Operating conditions
temperature -10°C ÷ 40°C,
relative humidity 5% - 90%, no condensation
Dimensions
W=275, H=281, D+D1=102+14 [+/- 2mm]
W1=280, H1=285 [+/- 2mm]
Enclosure
Steel plate, DC01 1,0mm color white RAL 9003
Closing
Cheese head screw x 1 (at the front)
Notes
The enclosure does not touch the assembly surface so that cables can be led.
Gross/Net weight
2,6 / 2,8 kg
Protection class PN-EN 60950-1:2007
II (second)
Storage temperature
-20°C ÷ 60°C
Declarations
CE
*The given value of 30 W per port is the maximum value. The total power consumption should not exceed 48 W.

4
2. Installation
2.1. Requirements
1. The device should be mounted by a qualified installer, holding relevant permits and licenses (applicable and required
for a given country) for 230 V and low-voltage installations. It is required to install an installation switch with a nominal
current of min. 3 A in the power supply circuits outside the power supply unit.
2. The device shall be mounted in confined spaces, according to the environment class II, with normal air humidity
(RH=90% max. without condensation) and the temperature from -10°C to +40°C.
3. The switch shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of
the enclosure. Before installation, prepare a Switch'a load balance. The given value of 30 W per port is the maximum
value referring to a single output. The total power consumption should not exceed 48 W. The increased demand for
power is particularly evident in the case of cameras with heaters or infrared illuminators - when launching these
features, the power consumption increases rapidly, which may adversely affect the operation of the switch. As the
device is designed for a continuous operation and is not equipped with a power-switch, therefore an appropriate
overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed about the
method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical system shall follow
valid standards and regulations.
2.2. Installation procedure
Before installation, cut off the voltage in the 230 V power-supply circuit.
To switch power off, use an external switch, in which the distance between the contacts of all
poles in the disconnection state is not less than 3mm.
1. Mount the PSU in a selected location and connect the wires.
2. Connect the power cables (230 V) to L-N clips of the PSU.
The shock protection circuit shall be performed with a particular care, i.e. the yellow and green wire
coat of the power cable shall stick to one side of the terminal - marked with ‘ ‘symbol on the PSU
enclosure. Operation of the PSU without the properly made and fully operational shock protection
circuit is UNACCEPTABLE! It can cause a device failure or an electric shock.
3. Connect the ground wire to the terminal marked with the symbol (power supply module connector). Use a three-
core cable (with a yellow and green protection wire) to make the connection. Lead the cables to the appropriate clips
through the insulating bushing of the connection board.
4. Connect the power (230 V).
5. Connect the camera cables to the RJ45 connectors (PoE connectors).
6. Check the optical indication of the switch operation.
7. After installing and checking proper working, the enclosure can be closed.
Connection schemes

5
3. Optical indication.
Table 4. Indication of the switch operation
OPTICAL INDICATION OF THE SWITCH's POWER SUPPLY
GREEN LED LIGHT (Power)
Indication of the switch's
power supply
OFF –no power supply of the switch
ON –power supply on, normal operation
OPTICAL INDICATION AT THE PoE PORTS (1÷4)
GREEN LED LIGHT
Indication of the PoE power
supply at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant
with the IEEE802.3af/at standard)
ON –power supply at the RJ45 port
Blinking –short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10Mb/s or 100Mb/s
Blinking –data transmission
OPTICAL INDICATION AT THE UP LINK PORTS
GREEN LED LIGHT
OFF- no connection or device connected /the device is connected 10Mb/s
ON –the device is connected 100Mb/s
YELLOW LED LIGHT (LINK)
The connection status of
LAN devices,
10MB/s or 100Mb/s
and data transmission
OFF- no data transmission
ON - the device is connected 10Mb/s or 100Mb/s
Blinking –data transmission
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment
should be disposed of separately from normal household waste .
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], sal[email protected]
http:// www.pulsar.pl, www.zasilacze.pl