PureMate PM 1550 User manual

CERAMIC TOWER HEATER
Model No: PM1550

SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock or injury to
persons or property:
Always operate the product from a power source of the
same voltage, frequency and rating as indicated on the
product identification plate.
-
Remove the unit from its packaging and check to make sure
it is in good condition before using.
-
Do not let children play with parts of the packing ( such as
plastic bags)
-
Close supervision is necessary when the product is used by
or near children or infirm persons. Do not allow children to
use it as a toy.
-
Do not operate any product with a damaged cord or plug,
or after the product malfunctions, or is dropped or appears
damaged in any way. Return the complete product to the
place of purchase for inspection, repair or replacement.
-
Thank you for purchasing the innovative product the PureMate
ceramic tower heater. We wish you many years of healthy
indoor air and warmth with this efficient and effective product.
1

Before unplugging the power cord, be sure to turn the
power off. When touching the unit, be sure your hands are
dry to prevent electrical shock.
-
Ensure the cord is fully extended before use and arrange it
so that it is not in contact with any part of the heater.
-
In use, some parts of the heater are hot. When moving, hold
the heater only by the handle provided.
-
Do not use the heater in areas such as garages where
petrol, paint or other flammable substances are used or
stored.
-
Do not use near or point the heater to furniture, animals,
curtains or other inflammable objects. Keep combustible
materials such as furniture, bedding and any other
combustible materials at least 1 metre from the front and
sides, and from the rear of the heater.
-
Do not place the cord under carpet or cover with throw rugs
or furniture. Arrange the cord so that it cannot be tripped
over.
-
Do not place the heater on bedding or on thick and long
pile carpet where the openings may be blocked.
-
To reduce the risk of electric shock, do not immerse or
expose the product or flexible cord to rain, moisture or any
liquid other than those necessary for correct operation of
the product.
-
2

This product should not be used in the immediate vicinity of
water, such as bathtub, washbowls, bathroom swimming
pool etc. where the likelihood of immersion or splashing
could occur.
-
Switch off and unplug from outlet when not in use, before
assembling or disassembling parts and before cleaning.
Remove by grasping the plug - do not pull on the cord.
-
A common cause of overheating is deposits of dust and fluff
entering the heater. Ensure these deposits are removed
regularly by unplugging the heater, allowing it to cool and
cleaning as described in the Care, Cleaning and Storage
section.
-
Be sure that no other high current appliances are plugged
into the same circuit with your heater as an overload can
occur.
-
Avoid the use of an extension cord as the extension cord
may overheat and cause a risk of fire.
-
Do not use the appliance for other than its intended use.
-
Do not use outdoors. FOR INDOOR USE ONLY.
-
Do not leave the appliance unattended when switched on.
-
Do not place objects on the product or allow objects to
obstruct the inlet or outlet openings, or operate in close
proximity to walls or curtains, etc. Do not cover the unit when
in operation.
-
3

Do not locate the heater immediately below a socket-outlet.
-
The use of attachments or accessories not recommended
or sold by the product distributor may cause personal or
property hazards or injuries.
-
This product is intended for normal domestic/household
use only.
-
Use this heater as described in this manual. Any other uses,
not recommended by the manufacturer, may cause fire,
electric shock, or injury to persons and may void the
warranty.
-
Use only an approved extension cord that is suitable for the
appliance rating!
-
Do not lay the cord under a carpet. Do not lay rugs, mats or
similar articles on it. Position the cord so that it does not pose
an obstruction or a tripping hazard.
-
Never pull the plug out of the socket at the cord!
-
Always disconnect the mains plug when the appliance is
not in use.
Attention! The appliance may only be used for normal
domestic use and not for industrial purpose.
-
4

5
COMPONENTS
Remote Control Storage
Handle
Air inlet
Master Switch
Power cord
Control Panel
Air Outlet
Base
Oscillation
Oscillation
Heat Mode
Timer
ON/OFF
ON/OFF
Temperature
increase
Temperature
increase
Temperature
Decrease
Temperature
Decrease
Timer
Heat Mode
CONTROL PANEL & REMOTE CONTROL

6
OPERATING INSTRUCTIONS
BEFORE USE
Before use, remove all packaging and insect the appliance
for any damages. If there are appears to be any damages,
please contact place of purchase for a replacement.
-
Ensure that all the accessories are included as per diagram
above before you continue with installation.
-
Ensure that the location of the heater is not directly under a
power socket and that a power socket is available to power
the appliance for use.
-
Plug the unit in and turn on the main power switch at the
back of the unit.
Press the Standby button to turn on the unit, this will enter Fan
Mode. Press again to turn off.
Press once to activate Low Heat (1100W). Press again to
activate High Heat (2000W)
Press to increase the desired room temperature.
+
Press to decrease the desired room temperature.
-
Temperature can be set between 10 - 49°C
-
When the heater has reached the desired set temperature,
the fan mode will continue to blow until the temperature has
dropped to 2°C below the et temperature (the heater will
automatically turn on the low heat setting, if the temperature
drops 4°C below the set temperature the heater will
automatically choose the high heat setting.)
-
Press to activate oscillation. Press again to stop oscillation.
Press until you reach the desired number of hours (up to
8hrs) before you want the heater to turn OFF.
PLEASE NOTE: When the heater has been turned off, the fan will continue
to work for 30 - 60 seconds to cool the appliance.
Note: temperature set using the + / - buttons will not be reached if it is
less than the current room temperature.

7
DISPLAY LIGHT:
After no manual operation after 10 minutes under the working
condition of the product. All functions remain unchanged and
the display turns off.
Press any key, including remote control, to cancel.
REMOTE CONTROL BATTERY
The remote control requires 1 CR2025 3V lithium battery (not
included)
Important: Follow the instructions of use and the recycle rules
given on the battery packaging.
Open the battery compartment by sliding the cover down.
-
Insert the battery into the compartment,
observing the polarity in the diagram (see below drawing).
-
Close the battery compartment.
-

8
SAFETY FEATURES
OVERHEAT PROTECTION
-
In the event of abnormal overheating, a safety device shuts
down the appliance automatically. After a short cooling
down phase, the appliance is ready for use again.
-
This heater is protected with an overheat protection that
switches off the appliance automatically in case of
overheat, e.g. due to the total or partial obstruction of the
grids. In this case, unplug the appliance, wait about 30
minutes for it to cool and remove the object which is
obstructing the grids. Then switch it back on as described
above. The appliance should operate normally. Should the
pr
problem persist, please contact the nearest customer
service.
-
If you still notice the same defect as above mentioned,
remove the plug from the socket and consult your
authorized dealer to your after-sales service department.
-
During use, do not touch or cover the air outlet. This may
cause the unit to overheat, and the safety device to
operate.
-
The unit is also fitted with a tip over switch. Do not use on
thick and long pile carpets, as the heater may not work, due
the tip over switch not been activated.

9
DISPOSAL OF THIS DEVICE
At the end of the product life cycle, you should not
throw this machine into the normal household
garbage but ring the product to a collection point for
the recycling of electrical and electronic equipment.
SPECIFICATIONS
220-240V ~ 50Hz
Power Supply:
Power Consumption: 2000W (High Setting)
Certifications: UKCA, CE, Rohs
Net Weight: 2.5 kg
Gross Weight: 3.3 kg
Dimensions: 19 x 19 x 57.2 cm
-
If the appliance is not used for an extended period it must
be protected against excessive dust and dirt. Please
dismount the heater and store in a dry place away from
sunlight and dirt.
Clean the air inlet and outlet regularly with a vacuum
cleaner.
-
Never immerse the appliance in water!
-
Never use flammable or abrasive cleaning agents such as
benzene or spirit to clean the appliance.
-
-
Clean the housing with a lightly damp cloth, a vacuum
cleaner or a dusting brush.
-
Your appliance must be switch OFF via the main power
supply and unplugged before proceeding with any
cleaning work.
CLEANING & MAINTENANCE