PureTools PT-SW-HD41E User manual

User Manual
PT-SW-HD41E
User Manual
4x1 HDMI Switcher HDMI2.0 with Auto Sense and ARC
Model PT-SW-HD41E
Designed in Germany
© 2018 PureLink GmbH All rights reserved. V1.0

User Manual
PT-SW-HD41E
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual are for reference only. Different model layouts and specifications are subject
to the physical product.
This manual is for operation instructions only, not for any maintenance usage.
In the constant effort to improve our product, we reserve the right to make changes in
functions or parameters without prior notice or obligation.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. It has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in
a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

User Manual
PT-SW-HD41E
REACH | 1907/2006/EU
ROHS | 2011/65/EU
PureLink hereby declares that this product PureTools PT-SW-HD41E complies with
Directives 1907/2006/EU und 2011/65/EU.
EMC / LVD (Electro Magnetic Compatibility / Low Voltage Directive)
PureLink GmbH hereby declares that this product PureTools PT-SW-HD41E
complies with Directives 2014/30/EU and 2014/35/EU. The full text of the EU
Declaration of Conformity is available at the following Internet address:
http://www.purelink.de/ce/4251364718414_CE.pdf

User Manual
PT-SW-HD41E
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before
using the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material
for possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module
immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

User Manual
PT-SW-HD41E
Table of Content
1. Product Introduction ..................................................................................................................1
1.1 Features ..............................................................................................................................1
1.2 Package List .......................................................................................................................2
2. Technical Specification..............................................................................................................3
3. Panel Description........................................................................................................................4
3.1 Front Panel.........................................................................................................................4
3.2 Rear Panel...........................................................................................................................5
4. System Connection.....................................................................................................................6
4.1 Usage Precaution..............................................................................................................6
4.2 System Diagram................................................................................................................6
5. Source Button Control................................................................................................................7
5.1 Manual Switching .............................................................................................................7
5.2 Automatic Switching........................................................................................................7
6. IR Remote Control.......................................................................................................................8
7. RS232 Control..............................................................................................................................9
7.1 RS232 Control Software .................................................................................................9
7.2 RS232 Command ........................................................................................................... 11
7.2.1 Signal Switching................................................................................................. 11
7.2.2 Source Device Control...................................................................................... 11
7.2.3 Audio Selection.................................................................................................. 12
7.2.4 Display Device Control..................................................................................... 13
7.2.5 System Control................................................................................................... 13
8. EDID Management.................................................................................................................... 14
8.1 Predefined EDID Setting.............................................................................................. 14
8.2 User Defined EDID Setting.......................................................................................... 15
9. ARC Mode ................................................................................................................................... 16
10. Firmware Upgrade................................................................................................................. 17
11. Panel Drawing......................................................................................................................... 18
12. Troubleshooting & Maintenance ....................................................................................... 19
13. After-Sales Service ................................................................................................................ 20

User Manual
PT-SW-HD41E
1
1. Product Introduction
The PT-SW-HD41E is an ultrathin auto switcher with four HDMI video inputs and one
HDMI output. This switcher supports HDMI video resolution up to 4Kx2K@60Hz
4:4:4 HDR and multichannel audio. Except passing EDID information from the
display, there are multiple built-in EDID settings to simplify an installation. The
switcher will de-embed digital stereo audio to provide an analog audio source for
an existing audio system. The switcher also supports audio return channel (ARC) for
transmitting audio back to HDMI input port from the connected display.
In auto-switch mode, it switches to an HDMI input as soon as a new source is
connected. When the active input is removed, the switcher will select the first
source on the lowest numbered input. The switcher may also be controlled via
RS232, IR with the included remote, or from the source button on the front of the
switcher.
1.1 Features
Switches any one of four HDMI inputs to one HDMI output.
Supports video resolution up to 4Kx2K@60Hz 4:4:4 HDR.
18Gbps high bandwidth.
Fully compliant with the HDMI 2.0 and HDCP2.2 specifications.
Supports audio return channel (ARC).
Advanced EDID management: multiple preset and user defined allowed.
Controllable via RS232 and IR.
Supports CEC.
Provides seven LEDs to indicate the current operating status and to assist
troubleshooting an installation.
Firmware upgrade by Micro-USB port.

User Manual
PT-SW-HD41E
2
1.2 Package List
1x HDMI2.0 4x1 Switcher
2x Mounting Ears
4x Mounting Screws
4x Plastic Cushions
1x RS232 Cable (3.5mm to DB9)
1x IR Remote
1x IR Receiver
1x Power Adapter (5V DC 1A)
1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

User Manual
PT-SW-HD41E
3
2. Technical Specification
Video Input
Input
(4) HDMI
Input Connector
(4) Female type-A HDMI
HDMI Input Resolution
Up to 4Kx2K@60Hz 4:4:4
HDMI Standard
2.0
HDCP Version
2.2
Video Output
Output
(1) HDMI
Output Connector
(1) Female type-A HDMI
HDMI Output Resolution
Up to 4Kx2K@60Hz 4:4:4
HDMI Standard
2.0
HDCP Version
2.2
Audio
Output
(1) AUDIO
Output Connector
(1) 3.5mm mini stereo audio jack
Audio Format
PCM
Audio Output Impedance
70 Ohms
Frequency Response
20Hz to 20kHz, ±3dB
Control
Control
(1) IR IN; (1) RS232
Control Connector
(2) 3.5mm mini jack
General
Bandwidth
18Gbps
Operation Temperature
-10℃~ +55℃
Storage Temperature
-25℃~ +70℃
Relative Humility
10%-90%
Power Supply
Input:100V~240V AC; Output: 5V DC 1A
Power Consumption
5W(Max)
Dimension (W*H*D)
194mm x 15mm x 81mm
Net Weight
324g

User Manual
PT-SW-HD41E
4
3. Panel Description
3.1 Front Panel
①Auto/Source Button:
Press to switch to next input source.
Press and hold at least three seconds to switch between manual mode and
auto mode.
②Power LED: The LED illuminates red when power is applied.
③Audio Mode LED:
Illuminates green when de-embedding audio.
Illuminates yellow when in ARC mode.
④Switching Mode LED:
Illuminates green in manual switch mode.
Illuminates yellow in auto-switch mode.
⑤Input 1~4 LED: The LED illuminates green when there is HDMI input on the
corresponding channel.
⑥FIRMWARE: Micro-USB port for firmware upgrade.
FIRMWARE
AUTO
SOURCE AUDIO MODE 1 2 3 4
12345 6

User Manual
PT-SW-HD41E
5
3.2 Rear Panel
①IN 1~4: Four type-A female HDMI input ports to connect HDMI sources. The
input 4 port supports ARC.
②OUT: Type-A female HDMI output port to connect HDMI display.
③AUDIO: 3.5mm mini jack for analog audio output.
④RS232: 3.5mm mini jack to connect control device (e.g. PC).
⑤IR IN: 3.5mm mini jack to connect the included IR receiver for remote control.
⑥EDID: 4-pin DIP switch for EDID setting.
⑦DC 5V: DC port to connect a 5V DC AC power adapter.
Note: Output HDCP compliant status depends on input signal. When the input signal is
with HDCP, then output signal is with HDCP and vice versa.
DC 5VEDIDIR INRS232AUDIOOUT
IN 1 IN 2 IN 3
1234567

User Manual
PT-SW-HD41E
6
4. System Connection
4.1 Usage Precaution
Make sure all components and accessories included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All of the power switches, plugs, sockets, and power cords should be insulated
and safe.
All devices should be connected before power on.
4.2 System Diagram
The following diagram illustrates typical input and output connections that can be
utilized with this switcher:
Game Console Laptop
STB
5 6 7
Receiver Remote
Central Control
System
Ray-Blu DVD
TV Speaker
HDMI:
Control:
Audio:
RS232:

User Manual
PT-SW-HD41E
7
5. Source Button Control
5.1 Manual Switching
When the switcher is in manual switching mode, the Switching Mode LED will be
green, and please press Auto/Source button to switch to the next input.
5.2 Automatic Switching
To enable automatic switching, press and hold the Auto/Source button for three
seconds. The Switching Mode LED will turn to yellow.
When in auto-switch mode, the switcher follows the rules in the certain
circumstances:
New Input: Upon detecting a new input, the switcher will automatically select the
new source.
Reboot: Once power is restored to the switcher, if the last selected source is still
available, the switcher will still output this signal, otherwise, the switcher will
switch to the first available active input starting at HDMI Input 1.
Source Removed: When an active source is removed, the switcher will switch to
the first available active input starting at HDMI Input 1.

User Manual
PT-SW-HD41E
8
6. IR Remote Control
Please connect an IR receiver to the IR input port; the IR remote is used for signal
switching and it can also be used to control source and display devices based on
CEC function.
Note:
Due to the HDMI input 4 port does not support CEC, the source device connected to
this port can not be controlled by IR remote.
The source and display devices are required to support CEC when the IR remote is
used to control them.
INPUTS:
1~4: Select the corresponding input source.
MANUAL/AUTO: Switch Auto or manual mode.
SOURCE: Control the input source (e.g. DVD).
DISPLAY: Control the display (e.g. HDTV).

User Manual
PT-SW-HD41E
9
7. RS232 Control
Connect the switcher to the control device (e.g. PC) with RS232 cable and set the
parameters in the right manner, the control device is capable to control this
switcher by RS232 commands.
7.1 RS232 Control Software
Installation: Copy the control software file to the computer connected with this
switcher.
Uninstallation: Delete all the control software files in corresponding file path.
Basic Settings
First of all, please connect all needed input devices and output devices, then to
connect it with a computer which is installed with RS232 control software.
Here take the software CommWatch.exe as example.
Double-click the following icon:

User Manual
PT-SW-HD41E
10
The interface of the control software is shown as below:
Please set the parameters of COM number, bound rate, data bit, stop bit and the
parity bit correctly, then the RS232 commands can be sent in Command Sending
Area.
Baud rate: 9600;
Data bit: 8;
Stop bit: 1;
Parity bit: none.
Parameter configuration area
Monitoring area, indicates if
the command sent works.
Command sending area

User Manual
PT-SW-HD41E
11
7.2 RS232 Command
Note: All commands must be ended with “<CR><LF>”.
7.2.1 Signal Switching
Function
Command
Feedback Example
Switch to HDMI input 1.
>>HDMI1
<<HDMI1
Switch to HDMI input 2.
>>HDMI2
<<HDMI2
Switch to HDMI input 3.
>>HDMI3
<<HDMI3
Switch to HDMI input 4.
>>HDMI4
<<HDMI4
Enable auto-switching mode.
>>AUTO
<<AUTO Switch
Enable manual switching mode.
>>MANUAL
<<MANUAL Switch
7.2.2 Source Device Control
Note:
The input source device is required to support CEC.
Due to the HDMI input 4 port does not support CEC, the source device connected to
this port can not be controlled by IR remote.
Function
Command
Feedback Example
Turn on the input source device,
e.g. Blue-ray DVD.
>>SRCOn
<<SRCOn
Turn off the input source device,
e.g. Blue-ray DVD.
>>SRCOff
<<SRCOff
Play
>>SRCPlay
<<SRCPlay

User Manual
PT-SW-HD41E
12
Function
Command
Feedback Example
Pause
>>SRCPause
<<SRCPause
Stop
>>SRCStop
<<SRCStop
Fast Forward x1
>>SRCForward
>>SRCForward
Fast Rewind x1
>>SRCBackward
<<SRCBackward
Next Section
>>SRCSkipForward
>>SRCSkipForward
Previous Section
>>SRCSkipBackward
<<SRCSkipBackward
Open the menu setting
>>SRCMenu
>>SRCMenu
Go back
>>SRCBack
>>SRCBack
Confirm (OK)
>>SRCOk
>>SRCOk
Exit
>>SRCExit
>>SRCExit
Up direction
>>SRCUp
>>SRCUp
Down direction
>>SRCDown
>>SRCDown
Left direction
>>SRCLeft
>>SRCLeft
Right direction
>>SRCRight
<<SRCRight
7.2.3 Audio Selection
Function
Command
Feedback Example
Select ARC audio channel.
>>AUDExternal
<<AUDExternal
Select the HDMI audio input
channel.
>>AUDInternal
>>AUDInternal

User Manual
PT-SW-HD41E
13
7.2.4 Display Device Control
Note: The display device is required to support CEC.
Function
Command
Feedback Example
Turn on the display device, e.g.
HDTV.
>>TVOn
>>TVOn
Turn off the display device, e.g.
HDTV.
>>TVOff
>>TVOff
Volume up.
>>TVVOL+
>>TVVOL+
Volume down.
>>TVVOL-
>>TVVOL-
Mute.
>>TVMUTE
>>TVMUTE
Unmute
<<TVUNMUTE
<<TVUNMUTE
7.2.5 System Control
Function
Command
Feedback Example
System reset.
>>RESET
>>RESET
Get system information.
>>SYSInfo
<<AUDExternal
<< PT-SW-HD41E
<< V1.0.0
<< --------
<<HDMI1
<<Auto Switch
<<AUDExternal
<<EDID0

User Manual
PT-SW-HD41E
14
8. EDID Management
8.1 Predefined EDID Setting
The rear panel boasts a 4-pin DIP switch to set the predefined EDID. The ten types
of embedded EDID and their corresponding switch status are shown in the below
list.
When in the lower
position, the switch
represents “ON”,
while putting the
switch in the up
position, it
represents “OFF”.
ID
Switch
Status
Video
Audio
0
0000
Pass though
Pass though
1
0001
1920x1080p@60Hz 4:4:4
RGB 8bit
Stereo
2
0010
1920x1080p@60Hz 4:4:4
RGB 8bit
High
Definition
3
0011
1920x1080p@60Hz 4:4:4
RGB 12bit
Stereo
4
0100
1920x1080p@60Hz 4:4:4
RGB 12bit
High
Definition
5
0101
3840x2160p@60Hz 4:2:0
RGB 8bit
Stereo
6
0110
3840x2160p@60Hz 4:2:0
RGB 8bit
High
Definition
7
0111
3840x2160p@60Hz 4:4:4
RGB 10bit HDR
Stereo
8
1000
3840x2160p@60Hz 4:4:4
RGB 10bit HDR
High
Definition
9
1001
1280x800@60Hz
Stereo
10
1010
1920x1200@60Hz
Stereo

User Manual
PT-SW-HD41E
15
8.2 User Defined EDID Setting
Except directly invoking the embedded EDID, the specific EDID can be customized.
There are five EDID can be customized following the below operations.
1) Rename the user defined EDID according the following format.
EC_xx_xxxx_xxx.bin
EC: Represents EDID.
xx: Represents EDID ID. It is 11~15.
xxxx: Represents the video parameter.
xxx: Represents the audio format.
Example: EC_11_720P_LPCM.bin
2) Power on the switcher, and then connect the switcher to the PC with USB cable.
The PC will automatically detect a U-disk named of “BOOTDISK”.
3) Double-click the U-disk, a file named of “READY.TXT” would be showed.
4) Copy the user defined EDID (such as EC_11_720P_LPCM.bin) to the “BOOTDISK”
U-disk.
5) Reopen the U-disk to check the filename “READY.TXT” whether automatically
becomes “SUCCESS.TXT”, if yes, the user defined EDID was imported into the
switcher and saved as its corresponding EDID ID successfully.
6) Repeat the above third to fifth step to copy other user defined EDIDs to the
“BOOTDISK” U-disk.
7) Remove the USB cable, connect the adaptor to power on the switcher.
8) The new EDID also can be invoked via the 4-pin DIP switch directly. The EDID ID
and its corresponding switch status are shown in the below list.
ID
Switch Status
11
1011
12
1100
13
1101
14
1110
15
1111