PureTools PT-SW-HDBT41 User manual

User Manual
PT-SW-HDBT41
User Manual
4x1 HDBaseT Switcher with 4K 40m Extension
Model PT-SW-HDBT41
Designed in Germany
© 2019 PureLink GmbH All rights reserved. V1.0

User Manual
PT-SW-HDBT41
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual are for reference only. Different model layouts and specifications are subject
to the physical product.
This manual is for operation instructions only, not for any maintenance usage.
In the constant effort to improve our product, we reserve the right to make changes in
functions or parameters without prior notice or obligation.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. It has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in
a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

User Manual
PT-SW-HDBT41
REACH | 1907/2006/EU
ROHS | 2011/65/EU
PureLink hereby declares that this product PureTools PT-SW-HDBT41 complies with
Directives 1907/2006/EU und 2011/65/EU.
EMC / LVD (Electro Magnetic Compatibility / Low Voltage Directive)
PureLink GmbH hereby declares that this product PureTools PT-SW-HDBT41
complies with Directives 2014/30/EU and 2014/35/EU. The full text of the EU
Declaration of Conformity is available at the following Internet address:
http://www.purelink.de/ce/4251364710630_CE.pdf

User Manual
PT-SW-HDBT41
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before
using the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material
for possible future shipment.
Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
Do not put any heavy items on the extension cable in case of protrusion.
Do not remove the housing of the device as opening or removing the housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with sufficient ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module
immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

User Manual
PT-SW-HDBT41
Table of Content
1. Product Introduction ..................................................................................................................1
1.1 Features ..............................................................................................................................1
1.2 Package List .......................................................................................................................2
2. Technical Specification..............................................................................................................3
3. Panel Description........................................................................................................................4
3.1 Front Panel.........................................................................................................................4
3.2 Rear Panel...........................................................................................................................5
4. System Connection.....................................................................................................................6
4.1 Usage Precaution..............................................................................................................6
4.2 System Diagram................................................................................................................6
5. Button Control..............................................................................................................................7
6. GUI Control ...................................................................................................................................9
6.1 Video Tab......................................................................................................................... 10
6.2 Tags Tab ........................................................................................................................... 11
6.3 RS232 Tab ....................................................................................................................... 12
6.4 Configuration ................................................................................................................. 13
6.5 Network Tab.................................................................................................................... 14
6.6 Password Tab.................................................................................................................. 15
6.7 GUI Upgrade.................................................................................................................... 16
7. RS232 Control........................................................................................................................... 17
7.1 RS232 Control Software .............................................................................................. 17
7.2 RS232 Command ........................................................................................................... 19
7.2.1 Device Control.................................................................................................... 19
7.2.2 Signal Switching................................................................................................. 20
7.2.3 Baud Rate Setting .............................................................................................. 21
8. IR Control.................................................................................................................................... 22
9. Firmware Upgrade.................................................................................................................... 26
10. Panel Drawing......................................................................................................................... 27
11. Troubleshooting & Maintenance ....................................................................................... 28
12. After-Sales Service ................................................................................................................ 29

User Manual
PT-SW-HDBT41
1
1. Product Introduction
Thanks for choosing the PT-SW-HDBT41 4x1 HDBaseT Switcher with automatic
signal switching. The switcher features four HDBaseT inputs, one HDBaseT output
and one HDMI output. It also supports HDMI 1.4 and video resolutions up to
4K@60Hz 4:2:0.
In auto-switch mode, it switches to an HDBaseT input as soon as a new source is
connected. When the active input is removed, the switcher will select the first
source on the lowest numbered input. The switcher can also be controlled via
RS232, IR with an appropriate control system or via front panel buttons.
1.1 Features
Switches any of the four HDBaseT inputs to either the HDBaseT output or HDMI
output.
Supports video resolutions up to 4K@60Hz, 4:2:0 as well as 1080p 3D.
Compliant with HDMI 1.4 and HDCP 2.2 specifications.
Extends 4K signals to distances up to 40 meters (131 ft.) and 1080p signals up to
70 meters (229 ft.) over a single CATx cable.
The HDBaseT output provides 48V PoC to power an HDBaseT receiver.
Controllable via RS232, IR or front panel buttons.
Bidirectional IR pass-through.
CEC pass-through.
Firmware upgrades using the type-A USB port.

User Manual
PT-SW-HDBT41
2
1.2 Package List
1x 4x1 HDBaseT Switcher
2x Mounting Ears
4x Mounting Screws
4x Plastic Cushions
1x Power Adapter (24V DC 1.25A)
1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

User Manual
PT-SW-HDBT41
3
2. Technical Specification
Video Input
Input
(4) HDBT
Input Connector
(4) RJ45
HDBT Input Resolution
Up to 4Kx2K@60Hz 4:2:0
Video Output
Output
(1) HDBT, (1) HDMI
Output Connector
(1) RJ45, (1) Female type-A HDMI
HDBT Output Resolution
Up to 4Kx2K@60Hz 4:2:0
HDMI Output Resolution
Up to 4Kx2K@60Hz 4:2:0 8bit
Control
Control
(1) FW, (1) RS232, (1) IR EYE, (1) IR IN, (1) IR OUT
Control Connector
(1) Type-A USB, (1) 3-pin terminal block, (3) 3.5mm mini jack
General
HDMI Standard
1.4
HDCP Version
2.2
HDCP Pass-through
Supported
CEC Pass-through
Supported
Hot-plug
Supported
Bandwidth
10.2Gbps
Transmission Standard
HDBaseT
Transmission Distance
1080p@60Hz ≤ 229 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
Operation Temperature
-5℃~ +55℃
Storage Temperature
-25℃~ +70℃
Relative Humidity
10%-90%
Power Supply
Input:100V~240V AC; Output: 24V DC 1.25A
Power Consumption
12W(Max)
Dimension (W*H*D)
220mm x 26mm x 100mm
Net Weight
670g

User Manual
PT-SW-HDBT41
4
3. Panel Description
3.1 Front Panel
①Power LED: The LED illuminates green when power is applied.
②Source Buttons and LEDs: Press button (1~4) to select the input source. The left
LED illuminates blue when there is HDBT input on the corresponding channel. If
the LED blinks blue, the corresponding input channel is selected but no signal
input is detected.
③AUTO Button and LED: Press the button to enable or disable auto switch mode.
The left LED illuminates blue in auto switch mode.
④SELECT button and LEDs: Press the button to switch the output channel between
HDBT and HDMI output. The corresponding HDBT or HDMI LED will illuminate
blue.
⑤TCP/IP: RJ45 to connect control device (e.g. PC) to control the switcher via GUI.
⑥FIRMWARE: Type-A USB port for firmware updates.
FWTCP IP/
1
INPUTS
23 4 AUTO FWSELECTHDBT HDMI
OUTPUTS
123456

User Manual
PT-SW-HDBT41
5
3.2 Rear Panel
①INPUTS: Four RJ45 input ports to connect compatible HDBaseT transmitters
using CATx Ethernet cables. Note that the connected transmitters cannot be
powered using PoC and must be powered using their power adaptors.
②HDBT OUTPUT: RJ45 output port to connect a compatible HDBaseT receiver by
CATx Ethernet cable. The receiver can be powered from the switcher with 48V
PoC output function.
③HDMI OUTPUT: Type-A female HDMI output port to connect HDMI display.
④RS232: 3-pin terminal block to connect a control device (e.g. PC) to control the
switcher via RS232 commands.
⑤IR EYE: 3.5mm mini jack to connect IR center control device to receive IR signal.
⑥IR IN: 3.5mm mini jack to connect the IR receiver for IR pass-through. When the
HDMI output is selected, the IR IN port is used with the IR OUT port of
transmitter to control the source device by IR.
⑦IR OUT: 3.5mm mini jack to connect the IR emitter for IR pass-through. When the
HDMI output is selected, the IR OUT port is used with the IR IN port of
transmitter to control the local HDMI display by IR.
⑧DC 24V: DC connector for the power adapter connection.
OUTPUTS
HDMI
DC 24V
RS232
Tx Rx
HDBT 3HDBT 2HDBT 1
INPUTS
HDBT 4 IR EYE IR IN IR OUT
CONTROL
HDBT
12345678

User Manual
PT-SW-HDBT41
6
4. System Connection
4.1 Usage Precaution
Make sure all components and accessories are included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All of the power switches, plugs, sockets, and power cords should be insulated
and safe.
All devices should be connected before power on.
4.2 System Diagram
The following diagrams illustrate typical input and output connections that can be
utilized with this switcher:
OUTPUTS
HDMI
DC 24 V
RS232
Tx Rx
HDB T 3HDB T 2H DBT 1
INPUTS
HDB T 4 IR EY E IR IN IR OU T
CONTROL
HDBT
PT-HDBT-703-TXWP Transmitter
PT-HDBT-703-TXWP Transmitter
PT-HDBT-703-TXWP Transmitter
PT-HDBT-703-TXWP Transmitter
IR ReceiverRemote
HDMI:
IR:
RS232:
HDBaseT:
4K TV
Laptop
Central Control System

User Manual
PT-SW-HDBT41
7
5. Button Control
Manual Switch Mode
Step1: Press SELECT to choose the HDBT or HDMI output channel,
Step2: Press button 1~4to select the input source channel.
Auto Switch Mode
Step1: Press SELECT to choose the HDBT or HDMI output channel,
Step2: Press AUTO to enable auto switch mode. The LED will illuminate blue.
When in auto switch mode, the switcher follows this sequence:
The switcher will switch to the first available active input starting at input 1 to 4.
Pressing the source button (1, 2, 3 or 4) can manually change the input source.
New Input: Upon detecting a new input, the switcher will automatically select the
new source.
OUTPUTS
HDMI
DC 24 V
RS232
Tx Rx
HDB T 3HDB T 2HD BT 1
INPUTS
HDB T 4 IR EY E IR IN IR OUT
CONTROL
HDBT
HDBT OUT
HDMI IN DC 12VRS232
Tx Rx
USB OUT
HDBT OUT
HDMI IN DC 12VRS232
Tx Rx
USB OUT
HDBT OUTHDMI IN DC 12VRS232
Tx Rx
USB OUT
HDBT OUTHDMI IN DC 12VRS232
Tx Rx
USB OUT
PT-HDBT-1002-Tx Transmitter
PT-HDBT-1002-Tx Transmitter
PT-HDBT-1002-Tx Transmitter
PT-HDBT-1002-Tx Transmitter
HDBT IN
HDMI OUT RS232
Tx Rx
USB IN
PT-HDBT-1002-Rx Receiver
Laptop
HDMI:
USB:
RS232:
HDBaseT:
Central Control System
Interactive
Whiteboard
IR:
Laptop
Laptop
Laptop
Laptop

User Manual
PT-SW-HDBT41
8
Reboot: Once power is restored to the switcher, the last selected output will remain
active. The switcher will switch to the first available active input starting at HDBT
input 1.
Source Removed: When an active source is removed, the switcher will switch to the
first available active input starting at HDBT input 1.
Pressing AUTO again exits the auto switch mode while the active input channel
remains.
When change the input source of the wallplate transmitter, the input channel of the
switcher will automatically switch to this input source.
Note: Factory default is auto switch on and HDBT output channel activated.

User Manual
PT-SW-HDBT41
9
6. GUI Control
The switcher can also be controlled via TCP/IP. The default IP setting is:
IP Address:
192.168.0.178
Subnet Mask:
255.255.255.0
Please type 192.168.0.178 in the internet browser to enter the log-in webpage:
Username: admin
Password: admin
Please type in the user name and password, then click Login to enter the section for
video switching.

User Manual
PT-SW-HDBT41
10
6.1 Video Tab
1) Select the HDBT or HDMI output channel.
2) Click the HDBT 1-4 buttons to select the input source respectively.
3) Click the AUTO button to enable or disable auto switch mode.

User Manual
PT-SW-HDBT41
11
6.2 Tags Tab
Modify the input button labels.

User Manual
PT-SW-HDBT41
12
6.3 RS232 Tab
Baud Rate: Supports 2400, 4800, 9600, 19200, 38400, 57600 or 115200.
Command: Type the command in this box to control the switcher.

User Manual
PT-SW-HDBT41
13
6.4 Configuration
Turn on or off 48V PoC power output.

User Manual
PT-SW-HDBT41
14
6.5 Network Tab
Set Static IP or Dynamic Host Configuration Protocol (DHCP).
Modify the static IP Address, Subnet Mask, and Gateway.

User Manual
PT-SW-HDBT41
15
6.6 Password Tab
Modify the login password.
Lock or unlock the front panel buttons.