Pyle PLMRF65MW User manual

PLMRF65MB
PLMRF65MW
PLMRF65MW / PLMRF65MB
Dual 6.5’’ Waterproof-Rated Bluetooth Marine Speakers
2-Way Coaxial Full Range Amplied Speaker System with Wireless RF Streaming (600 Watt)
Features:
• Includes (2) 6.5'' Coaxial Speakers (Active + Passive)
• Bluetooth Wireless Music Streaming Ability
• Wireless Radio Frequency (RF) Streaming Ability
• RF Audio Module Supports Additional Speaker
Connectivity
• Extended Range Streaming Performance
• Marine Grade Waterproof-Rated Construction
• Water-Resistant & Weatherproof Design
• Amplied Master Speaker with Built-in 2-Ch.
Digital Amplier
• 2-Way Active Powered Speaker System
• Impressive Wide-Bass Response
• Full Range Stereo Sound Reproduction
• Universal Standard OEM Replacement Size
• RCA Audio Aux (L/R) Connectors
• Hassle-Free Easy Access Speaker Terminals
• Daisy-Chain Ability (Active to Passive Speaker)
as Stereo System
• *Each Speaker Has the Ability to Serve as a Passive
Type Speaker
• Reinforced Surround with Dense Speaker Cone
• Rugged Machined Basket & Grill
with UV Resistant Housing
• Used For Car, Boat, O-Road & Marine Vehicle Applications
Technical Specs:
• Power Output: 600 Watt MAX (300 Watt RMS)
• Marine Grade Rating: IP-X4
• Speaker Composition: Polypropylene Cone,
Butyl Rubber Surround
• Voice Coil: 1.0'', Aluminum (x2)
• Tweeters: 0.5'', Neodymium Dome (x2)
• Impedance: 4 Ohm
• Sensitivity: 90 dB
• Circuit Magnet: 20 oz.
• Frequency Response: 85Hz-20kHz
• Active Speaker Weight: 1.71 lbs.
• Passive Speaker Weight: 1.67 lbs.
• Power Supply: DC 12V
• Sold as: Kit
What’s in the Box:
• (1) 6.5’’ -inch Active Speaker
• (1) 6.5’’ -inch Passive Speaker
• Cut-Out Template
• Mounting Screws
Bluetooth Connectivity:
• Receiver Built-into Active / Master Speaker
• Allows Instant Wireless Music Streaming
• Simple Setup & Hassle-Free Pairing Ability
• Works with All of Today’s Latest Devices
(Smartphones, Tablets, Laptops, Computers)
• Bluetooth Version: 4.2
• Bluetooth Network Name: ‘PyleUSA’
• Wireless Range: 30’+ ft. BT
(100’+ ft. RF Streaming)
Sizes / Dimensions:
• Total Diameter: 6.9’’-inches
• Cut-Out Diameter: 6.75’’ -inches
• Total Depth: 3.97’’-inches
• Mounting Depth: 3.1’’ -inches
www.PyleUSA.com
Dual6.5’’Waterproof-RatedBluetooth
MarineSpeakers
2-Way Coaxial Full Range Amplified Speaker System
with Wireless RF Streaming (600 Watt)
PLMRF65MW-PLMRF65MB

www.PyleUSA.com www.PyleUSA.com
PLMRF65MW - PLMRF65MB
Installation Guide
PLMRF65MW/PLMRF6MB Installation
Ways to Connect
• RF Wireless Audio Connection:
Install both speakers, as active powered speakers. Connect L and R Channel speakers, each to a 12V
power source. Then use pins to press the "CH Set" buttons, simultaneously to pair the speakers.
Upon successful power connection, the R Channel speaker LED indicator light will shine red -- and the
L Channel speaker LED indicator light will shine blue.
*Note: Recommended power installation should include a 10 amp fuse between the power source
and speakers, ensure a proper and adequate power connection is established.
Bluetooth Audio Connection:
Once the speakers are installed and powered, the Bluetooth network name from your device list will
appear as 'PyleUSA'. Upon successful Bluetooth pairing connection you will hear a connection tone
and the speakers will shine with a blue LED indicator light.
Aux-in (External Audio Source) Connection:
The R Channel speaker features low-level audio input connectors to stream audio from external
devices. Upon successful aux audio input connection, the R Channel speaker LED indicator light will
shine green.
*Note: The speakers must not be paired via Bluetooth wireless connection to allow Aux-in audio
mode.
Passive Speaker Connection:
Each speaker also has the ability to be used as a Passive-Type (un-powered) speaker. Ensure a proper
audio source connection is made via each speaker's 'Input Radio Speakers' connectors.
LED INDICATOR
Status
POWER ON
RCA AUX-IN Connection
Bluetooth Connection
Main Speaker ( R Channel) 2nd Speaker (L Channel)
BLUE
RED
GREEN
RED
BLUE
BLUE
BLUE
RED
RF Wireless Connection
I
II
III
II
Signal connection
as passive speaker
Signal connection
Using pins to push “CH Set” simultaneously
to get RF Wireless connection
as passive speaker
Audio Signal
Aux-In
(Follow on
Ways to Connect )
III
(Follow on Ways to Connect )
III
“ Bluetooth
Pairing Tone”
1.“Turn on Bluetooth”
2.“Choose PyleUSA”
I
CH Set CH Set