Pyle PSW503ST User manual

Warning: Some TV require two people to lift, as we are not responsible for any
personal injury or product damage due to mishandling.
Warning:
Fig 4b
Step 4: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.4a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.4b.
Step 4: Hanging display
Thank you for choosing our productsThank you for choosing our products
-8-
Multifunctional double deck wall mount
Tilt Flat Panel TV Bracket
Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Weight Capacity:10kg/22lbs~50kg/110lbs
TV size range: 26 ~42
Adjustable angle: 5 15
""
-～
Inside has balance adjust system
Bulit in leveler system
INSTALLATION GUIDE
IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.
IMPORTANT:
Item No.:PSW503STItem No.:PSW503ST
the facing of a quilt
Fig 4a
2,3
1
5
www pyleaudio com..
MADE IN CHINA
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
[phone]

Hardware List: Actual parts appearance and the quantity may different
with illustrated.
Hardware List:
4
4
H
I
J
K
4
4
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
ID Description
1
2
A
3
4
5
6
B
C
1
1
1
4
1
2
1
4
4
Wall mount
M4 mm×12 bolt
M4 mm×16 bolt
M5× mm16 bolt
M6×16mm bolt
M5×36mm bolt
M6×36mm bolt
Qty
D4
4
4
4
E
F
G
Cable Cover
Safe bolt
Box wrench
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall
Using a awl or nail to make where the nails are located, as shown as Fig.3b. Distance
between two nails for fixing wall mount must not less than 16 . Slide the plate into
position as required.(Fig.3c) Pre-drill these holes with a 5mm drill bit to at least
40mm in deep hole. Use wall mount as a template to mark the location of other three
holes and drill the same holes.
Fixthewallmounttothewallwith4longbolts(H)andwashers(J) .
-wooden, brick, concrete and stone.
Please make sure these holes are level and eudipleural.
by box wrench(6)
Wooden wall:
”
Wooden wall:
-2- -7-
A-F J
GI
HK
ID Description
Qty
Fig 3b Fig 3c
Brick, Concrete and Stone wall:
Using a awl or nail to make where the nails are located. Distance between two nails
for fixing wall mount must not less than 16 . Slide the plate into position as required.
(Fig.3c) Pre-drill these holes with a 10mm drill bit to at least 50mm in deep hole. Use
wall mount as a template to mark the location of other three holes and drill the same
holes. Please make sure these holes are level and eudipleural. Insert wall anchors(I)
into each of these holes. Attach the wall mount to the wall using 4 long bolts(H) and
washers(J)by box wrench(6).
”
Brick, Concrete and Stone wall:
1
2
5
3
4
Plate
Fig 3d
H
J
1
Balance-adjusting Using balance-adjusting system on the plate,
make sure whether wall plate is installed
balance. If not, then slide the wall plate let
pointer level in the center position.
Left bracket
Right bracket
6
6

-6- -3-
b
15 degree
viewing angle
eyelevel
a
Fig 3a
Step 3: mount to wall
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 3a).
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15 (Fig 3a).
For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
°
AttachStep 3: Attach mount to wall
WARNING
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
Note:
Caution:This Product LCD /Plasma Wall Mount Bracket is intended for use only
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Caution:
Step 1: Attach bracket to TV
CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-5 of these instructions for examples.
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts, spacers and washers for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly secure the
bolts.
Don't force the bolt into the hole, which will cause a damage of
equipments and injure of person. Don't use electric drill to fasten any bolts.
IMPORTANT:
Step 1: Attach bracket to TV
IMPORTANT
Step 2: Install the Cable Cover
Route the cables as required. Snap the cable cover into place onto
the rods (Fig. 2a), and then slide the cover into position as required.
(Fig. 2b)
Step 2: Install the Cable Cover
Fig 2a Fig 2a

2. Some displays have curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(K) between display and
thebracket.AsshowninFig1b.
Fig a
-4-
-5-
Following examples shows how to use bolts, spacers and square washers.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.
Fig 1a
M5 Fig bitM4 Fig bit
M6 Fig bit
A,B
3
G
2C
G
D
G
3
Fig 1b
M6 Fig bitM5 Fig bit
E
3G
KK
F
G
3