Pyronix Castle EURO 46 Series Owner's manual

Page: 1
Programming Reference
For the EURO 46, EURO 162 and
EURO 280 control panels
RINS1528-4
EN50131-3:2009
EN50131-1:2006+A1:2009
PD6662:2010
EURO 46S:
Security Grade 2
Environmental Class II
EURO 46L, EURO 162 & EURO 280:
Security Grade 3
Environmental Class II
Software Version >9.1

EURO 46, 162 & 280 Programming Manual
Page: 2
CONTENTS PAGE
CONTENTS PAGE......................................................................................................................................... 2
1. The Engineer Menu .................................................................................................................................. 3
1.1 Entering The Engineer Menu................................................................................................................. 3
1.2 Exiting The Engineer Menu................................................................................................................... 3
1.3 Useful Engineer Menu's........................................................................................................................ 3
2. System Overview .................................................................................................................................... 4
2.1 System Overview................................................................................................................................ 4
2.2 Wired Input Mappings ......................................................................................................................... 5
2.3 Wireless Input Mappings...................................................................................................................... 6
3. General Information ................................................................................................................................ 7
3.1 Default Codes .................................................................................................................................... 7
3.2 Initial Power Up.................................................................................................................................. 7
3.3 Testing The Keypad ............................................................................................................................ 7
3.4 Keypads / Readers.............................................................................................................................. 7
3.5 Text Programming .............................................................................................................................. 8
3.6 Grade 2 and Grade 3 Defaults .............................................................................................................. 8
3.7 Set / Unset System............................................................................................................................. 9
3.8 Forced Arm On Inputs ......................................................................................................................... 9
4. The Engineer Menu .................................................................................................................................10
4.1 Inhibit Fire & HU................................................................................................................................10
4.2 Software Revision ..............................................................................................................................10
4.3 Choose Mode ....................................................................................................................................10
4.4 Install ZEMs......................................................................................................................................11
4.5 Wireless Device Control ......................................................................................................................11
4.6 Change Inputs ..................................................................................................................................14
4.7 Assign Keypads/Readers.....................................................................................................................17
4.8 System Displays ................................................................................................................................20
4.9 Change Timers ..................................................................................................................................21
4.10 Date and Time.................................................................................................................................21
4.11 Exit Modes ......................................................................................................................................21
4.12 Change Codes .................................................................................................................................22
4.13 Volume Control................................................................................................................................23
4.14 Alarm Response...............................................................................................................................23
4.15 Change Outputs...............................................................................................................................24
4.16 Intelligent Set .................................................................................................................................26
4.17 Site Options ....................................................................................................................................26
4.18 Engineer Reset Options.....................................................................................................................27
4.19 Review Logs....................................................................................................................................28
4.20 Engineer Tests.................................................................................................................................29
4.21 Diagnostics .....................................................................................................................................31
4.22 Set Up Downloading .........................................................................................................................33
4.23 Program ARC / SMS? ........................................................................................................................35
4.24 Dial Out Menu .................................................................................................................................37
4.25 Clean Start .....................................................................................................................................38
Appendix A. Defaults ................................................................................................................................39
Appendix B. Input Types ...........................................................................................................................43
Appendix C. Timers ..................................................................................................................................45
Appendix D. Output Types .........................................................................................................................47
Appendix E. Content Types........................................................................................................................50
Appendix F. Fault Codes............................................................................................................................51
Default Codes: User Code: 1234, Master Manager Code: 2222, Engineer: 1111.
Factory Default Codes:
Clean start with the code ‘2000’ (GRADE 3 DEFAULTS) - Refer to page: 38
Clean start with the code ‘2002’ (GRADE 2 DEFAULTS) - Refer to page: 38
Other Codes: Keypad Security Code: ‘2000’, Delete All Wireless Data: ‘2000’

EURO 46, 162 & 280 Programming Manual
Page: 3
1. The Engineer Menu
The Engineer menu must be accessed in order to program all system configurations.
NOTE 1: All tamper alarms (including case tamper), will be disabled once in the Engineer menu.
NOTE 2: All personal attack and fire alarms will cause an alarm in the Engineer menu.
1.1 Entering The Engineer Menu
Access to the Engineer menu will be allowed if the EURO control panel is unset. If set, the E must be
unset first via a valid user code/tag/keyfob in order to gain access. If the 'Allow Engineer menu'
function in the Master Manager Menu is set as 'No', the message ‘Authorisation Required’ will be
shown and access will be denied until this option is set as 'Yes'.
1. Enter the Engineer code (default 1111).
2. Press if any faults appear.
3. 'SET/UNSET SYSTEM' is displayed (page:9).
4. Press .
5. 'FORCE ARM ON 1st INPUT' is displayed (page:9).
6. Press .
7. 'SOFTWARE REVISION' is displayed.
8. Engineers Menu has been accessed.
Refer to page: 10 for all functions.
NOTE: When the Engineer menu is accessed, a high pitch
tone is generated intermittently.
NOTE 1: It is recommended that a factory default (Clean Start) is performed after initial power up to
ensure that the correct defaults have been chosen (page: 38).
NOTE 2: Refer to Appendix F, page: 51 for all fault code display descriptions.
1.2 Exiting The Engineer Menu
1. On a Main Menu Item (a menu that is in capital
letters), press or scroll to 'EXIT ENGINEERS
MENU' and press .
1.3 Useful Engineer Menu's
WIRELESS DEVICE CONTROL (Page: 11): Learns and deletes all wireless inputs and bells if a
wireless ZEM (EURO-ZEM32-WE) is installed (Refer to the installation manual (RINS1529)). To
learn keyfobs enter the Master Manager menu and scroll to CHANGE CODES. (Refer to the user
manual (RINS1527))
CHANGE INPUTS (Page: 14): Programs all input types, attributes, areas and names and on the
EURO control panel.
ASSIGN KEYPADS/READERS (Page: 16): Assigns keypads, readers, and enables readers for entry
control. NOTE: Keypads and Readers must be addressed at the device and at the keypad. (Refer to
the installation manual (RINS1529)).
CHANGE CODES (Page: 22): Changes the Engineer code and Master manager code. To change user
codes enter the Master Manager menu and scroll to CHANGE CODES. (Refer to the user manual
(RINS1527)).
CHANGE OUTPUTS (Page: 24): Programs any outputs and assigns output modules if installed to
the EURO control panel.
DIAGNOSTICS (Page: 30): Displays the power, input status, wireless signal strength and wireless
battery levels.
PROGRAM ARC/SMS (Page: 35): Enables the modem (if connected) and allows signalling of
communication formats and SMS.
Enter Your Code
[ ]
SET / UNSET
SYSTEM?
FORCE ARM ON 1st
INPUT? [01]
EXIT ENGINEER
MENU?

EURO 46, 162 & 280 Programming Manual
Page: 4
2. System Overview
2.1 System Overview
EURO EURO 46
Double Pole
EURO 46
End of Line
EURO 162
iD
EURO 162
End of Line
EURO 280
iD
EURO 280
End of Line
Inputs (max) 46 162 280
Inputs (max iD) - 150 240
Inputs (max wireless inputs)
Using EURO-ZEM32-WE
32
(1 x ZEM32-WE)
96
(3 x ZEM32-WE)
96
(3 x ZEM32-WE)
Inputs (max wired ZEMs)
EURO-ZEM8+ 4 4 4 18 7 30
Set Points (Max) $ 6 16 30
Of which max keypads 6 16 30
Other Devices Max $ 5 15 29
Wireless Bells 2 2 2
Level Sets 6 12 14
Full Areas 6 12 14
Wards (Max) 5 15 29
Shunts 23 81 140
Wireless Keyfobs 32 32 32
User / Manager Codes £ 75 200 500
Duress / Guard Codes 10 20 20
Logs Mandatory 750 1000 1000
Logs Access 250 500 500
Logs Optional 250 500 600
Output Modules 2 8 16
EN Grade 3 (2 = Small casing) 3 3
Environment Class 2 2 2
Comms Modem, ATE Pins Modem, ATE Pins Modem, ATE Pins
Modem Type EURO DIGI-1200 (PSTN) EURO-073-ARM EURO-073-ARM
MSX card compatible 
Autoset & Gates 
Shunt, Day Alarm, Unset Input
Types 
Follow Input 
Special Log 
Intelligent Inputs Multiple Multiple Multiple
Display when Set 
Selectable Resistance Ranges 
Download When Set 
Remote Set and Soak 
Event Signalling to Insite 
Dial Out Menu Upload/
Commission
Upload/
Commission
Upload/
Commission
Power Supply
EURO 46S: 1.5A (small casing)
EURO 46L: 2A (large casing)
EURO 162/280: 2.5A
Rating Grade 1: 2.25A
Rating Grade 2: 1.4A
Rating Grade 3: 0.9A
£ Includes Engineer and Master Manager codes
$ Includes keypads, tag readers, and ZEM2Ps

EURO 46, 162 & 280 Programming Manual
Page: 5
2.2 Wired Input Mappings
EURO *46 EOL/DP 162iD 162EOL 280iD 280EOL
iD
End Station - 1-30 - 1-30 -
EOL
End Station 1-8 151-158 1-8 241-248 1-8
ZEM0 9-16 - 9-16 - 9-16
ZEM1 17-24 - 17-24 - 17-24
ZEM2 25-32 - 25-32 - 25-32
ZEM3 33-40 - 33-40 - 33-40
ZEM4 - - 41-48 - 41-48
ZEM5 - - 49-56 - 49-56
ZEM6 - - 57-64 - 57-64
ZEM7 - - 65-72 - 65-72
ZEM8 - - 73-80 - 73-80
ZEM9 - - 81-88 - 81-88
ZEM10 - - 89-96 - 89-96
ZEM11 - - 97-104 - 97-104
ZEM12 - - 105-112 - 105-112
ZEM13 - - 113-120 - 113-120
ZEM14 - - 121-128 - 121-128
ZEM15 - - 129-136 - 129-136
ZEM16 - - 137-144 - 137-144
ZEM17 - - 145-152 - 145-152
ZEM18 - - - - 153-160
ZEM19 - - - - 161-168
ZEM20 - - - - 169-176
ZEM21 - - - - 177-184
ZEM22 - - - - 185-192
ZEM23 - - - - 193-200
ZEM24 - - - - 201-208
ZEM25 - - - - 209-216
ZEM26 - - - - 217-224
ZEM27 - - - - 225-232
ZEM28 - - - - 233-240
ZEM29 - - - - 241-248
RKP0 41-42** 159-160 153-154 249-250 249-250
READ/RKP1 43-44** 161-162 155-156 251-252 251-252
READ/RKP2 45-46** - 157-158 253-254 253-254
READ/RKP3 - - 159-160 255-256 255-256
READ/RKP4 - - 161-162 257-258 257-258
READ/RKP5 - - - 259-260 259-260
READ/RKP6 - - - 261-262 261-262
READ/RKP7 - - - 263-264 263-264
READ/RKP8 - - - 265-266 265-266
READ/RKP9 - - - 267-268 267-268
READ/RKP10 - - - 269-270 269-270
READ/RKP11 - - - 271-272 271-272
READ/RKP12 - - - 273-274 273-274
READ/RKP13 - - - 275-276 275-276
READ/RKP14 - - - 277-278 277-278
READ/RKP15 - - - 279-280 279-280
READ = Reader
RKP = Remote Keypad
ZEM = Zone Expander Module

EURO 46, 162 & 280 Programming Manual
Page: 6
2.3 Wireless Input Mappings
EURO 46 Wireless 162 Wireless 280 Wireless
End Station - - -
ZEM0 9-16 9-16 9-16
ZEM1 17-24 17-24 17-24
ZEM2 25-32 25-32 25-32
ZEM3 33-40 33-40 33-40
ZEM4 - 41-48 41-48
ZEM5 - 49-56 49-56
ZEM6 - 57-64 57-64
ZEM7 - 65-72 65-72
ZEM8 - 73-80 73-80
ZEM9 - 81-88 81-88
ZEM10 - 89-96 89-96
ZEM11 - 97-104 97-104
2.3.1 Wireless ZEM (EURO-ZEM32-WE)
The wireless ZEM allows 32 inputs which are separated into 4 addresses (each address enables 8
wireless inputs). It is possible to mix the wired and wireless remote expanders. Please refer to
the installation manual (RINS1529) for more information.
2.3.2 Wireless ZEM (EUR-037R)
The Inovonics wireless ZEM is added to the system as if it was a wired ZEM and follows the same
zone mapping as the table on the previous page. Please refer to the installation manual
(RINS1529) for more information.

EURO 46, 162 & 280 Programming Manual
Page: 7
3. General Information
Please note that the number of areas, codes, inputs and outputs shown in this manual may differ to the
EURO control panel that is being used. Refer to 'System Overview' on page: 4 to see the maximum areas,
codes, inputs and outputs for each variant of the EURO control panel range.
3.1 Default Codes
User: 1234. Master Manager: 2222 Engineers: 1111
3.2 Initial Power Up
Power up the EURO control panel, an alarm will be generated.
1. Once power has been applied to the EURO control
panel, 'Please Wait' and then '485 Comms Lost' will
be displayed. After approximately one minute, the
LCD display will show th time on the display.
2. If only one LCD keypad is installed, this will be
addressed as 00 automatically.
NOTE: The wording 'EURO MERIDIAN' can be changed in the function ‘SYSTEM DISPLAYS'(page:20).
3.3 Testing The Keypad
With the system unset, press the key for 10 seconds at any keypad. This will cause all the LEDs
on that keypad to illuminate, and the LCD screen to scroll a display testing each pixel. The keypad
will revert to normal display approximately 10 seconds after the key is released.
3.4 Keypads / Readers
3.4.1 The Keypad
Additional keypads can be connected to the EURO control panel. Refer to the system overview
section (page: 4) for the maximum number of keypads that can be installed. Refer to the
installation manual (RINS1529) for connections details.
KEY FUNCTIONS:
a= Exit manager menu / Selects Area A.
b= Moves backwards to the previous
menu item / Selects Area B.
c= Enables chime and displays
additional information in the log / Scrolls
back ‘one’ in a sub menu / Selects Area C.
D= Moves forward in the log / scrolls
between options and enters the master
manager menu /Selects Area D.
I= Selects items and enters menus.
A= Cancels items, resets the panel and
moves to next item in a menu item.
NOTE: If any additional keypads are installed on the EURO control panel, it is possible to access
the Engineer menu on any keypad. For example, if the Engineer menu is accessed on keypad
address 0, the other keypads will display ‘system busy’, to access the Engineer menu on any
other keypad, press the key on the relevant keypad and the Engineer menu will be
displayed.
Addressing Keypads
To address further keypads on the EURO control panel, press and hold the Dkey until
'SECURITY CODE' is displayed. Enter '2000' and choose the relevant address and press the A
key. Please refer to the installation manual (RINS1529) for all connection details.
Please Wait...

EURO 46, 162 & 280 Programming Manual
Page: 8
3.4.2 The Internal Tag Reader (EUR-107)
The Internal tag reader can be used for setting/unsetting, entry control or access control. Refer
to the installation manual (RINS1529) for connection details.
Tag Area (Where a valid tag must
be presented to set/unset)
Alert LED
Alarm LED
Tamper LED
Fault LED
Unset LED
3.4.3 The External Tag Reader (EUR-108)
The Internal tag reader can be used for setting/unsetting, entry control or access control. Refer
to the installation manual (RINS1529) for connection details.
To set/unset the system using the External Tag Reader,
present a pre-programmed tag to the centre of the prox.
The prox will display the system status: Green = Unset.
Red = Set. Present the tag again within 10 seconds and
the system will set or unset.
The system will then set depending on the type of exit
mode programmed (Final door, Timed or Push to set)
3.5 Text Programming
Text may be programmed for input names, for the ‘sign-on’
message, and to identify the Set Level being set / unset. Each key is
allocated alpha-numeric and punctuation mark characters.
The EURO control panel incorporates predictive text, so the system
will predict the word that is being spelt. For example, if ‘B’ is
pressed, and then and ‘e’ is pressed, Bedroom will be displayed,
to accept this press . If the word that is required doesn’t appear
on the LCD display, type the word as normal.
To type a word, press the relevant key the appropriate number of
times – e.g. for the letter ‘k’ press twice, or for the letter ‘s’
press four times. For punctuation marks, press the key.
In addition, the keys are used as follows:
= make the character into a capital = move cursor left = clears cursor / adds a space
= moves cursor right
3.6 Grade 2 and Grade 3 Defaults
The security grade of the EURO control panel can either Grade 2 or Grade 3*.
In the 'CLEAN START' function (Page: 38), enter '2002' for Grade 2 defaults, or '2000' for Grade 3*
defaults.
*The EURO 46 Small control panel will only conform to Grade 2

EURO 46, 162 & 280 Programming Manual
Page: 9
3.7 Set / Unset System
Setting and unsetting the system can be done using the Engineer code (default 1111).
NOTE: The term 'areas' will refer to both areas and level sets in this manual, also note that the
number of areas and level sets will differ depending on the EURO control panel installed. To change
the EURO control panel into a level set system, please refer to 'SITE OPTIONS' (page: 26).
1. Enter the Engineer code (default 1111).
2. Press if any faults appear.
3. 'SET/UNSET SYSTEM' is displayed.
4. Press .
5. Select the areas to set. Press .
6. The setting period will begin.
7. Once the timer expires, and a beep is heard, control panel
is set.
8. To unset, enter the Engineer code again.
NOTE: If a wireless ZEM (EURO-ZEM32-WE) is installed, the
display will show 'Please Wait Setting Wireless' and then will
revert to the 'Setting' to display.
3.8 Forced Arm On Inputs
The 'Force Arm On Inputs' function enables two nominated inputs on the EURO control panel to be
set. Either input can be triggered to allow real life signalling or alarm testing. This function is useful
when a building is full of people and these tests are needed.
NOTE 1: The system will give the correct signalling response to the Setting, and any resulting alarm.
NOTE 2: If the system has been set by any other code, the Engineer code will unset the EURO
control panel.
9. Enter the Engineer code (default 1111).
10. Press if any faults appear.
11. 'SET/UNSET SYSTEM' is displayed.
12. Press .
13. 'FORCE ARM ON 1st INPUT' is displayed.
14. Enter the 1st input that is to be active. Press .
15. Enter the 2nd input that is to be active. Press .
16. Select the areas to set. Press .
17. The setting period will begin
18. Once the timer expires, and a beep is heard, the
EURO control panel is set and the 2 inputs chosen will
be active.
19. To unset, enter the Engineer code again.
SET / UNSET
SYSTEM?
Setting [007]
Full Set
FORCE ARM ON 1st
INPUT? [01]
FORCE ARM ON 2nd
INPUT? [01]

EURO 46, 162 & 280 Programming Manual
Page: 10
4. The Engineer Menu
Any programming is only saved when exiting the Engineer menu. It is recommended that a Clean start is
performed after initial power up (page: 38). This section follows the order of the Engineer menu.
4.1 Inhibit Fire & HU
This function allows the EURO control panel to respond to or inhibit Fire and Hold Up alarms, if the
Engineer menu is being used.
Inhibit Fire/HU Programming
1. Press or to scroll to 'INHIBIT FIRE/HU'. Press
.
2. Press or to select 'No' or 'Yes' to inhibiting
Fire and Hold Up alarms. Press .
4.2 Software Revision
This option identifies the software version number, software serial number and product.
Software Revision Programming
3. Press or to scroll to 'SOFTWARE REVISION'.
Press .
4. The software revision will be displayed and the EURO
panel. (e.g. V9.10) Press orto return to the
Engineer menu.
4.3 Choose Mode
This functions selects any End of Line resistor values for the inputs on the EURO control panel and
any Zone Expander Modules.
NOTE: Alarm 4K7, Tamper 2K2 must be selected if wiring double pole to the EURO 46/Zone
Expander Module.
4.3.1 Detection Mode
The EURO 162 or 280 can operate as an End of Line or iD control panel. Refer to 'Input
Mappings' (page: 5) for more information.
[0] iD [1] EOL
NOTE: This function (and iD wiring) is not available on the EURO 46.
4.3.2 EOL Range (End of Line Range)
EOL Mode programs all inputs on the EURO control panel and Zone Expander Modules (ZEMs)s to
operate as:
[0] Alarm: 1K, Tamper: 1K. [1] Alarm: 4K7, Tamper: 2K2.
[2] Alarm: 4K7, Tamper: 4K7. [2] Wide range.
4.3.3 EOL mode (Double End of Line (DEOL) or Single End of Line (SEOL))
EOL Mode programs all inputs on the EURO control panel and Zone Expander Modules (ZEMs)s to
operate as:
[0] Single End of Line (SEOL). [1] Double End of Line (DEOL).
4.3.4 Input Response Time
Input Response time programs the time that an input trigger must be present before the EURO
control panel system generates an alarm.
[01]-[30] = 100ms to 3000ms
NOTE: Settings above 400ms do not comply with PD6662/EN50131.
4.3.5 Input XDF
Do not change this setting unless instructed by customer support.
INHIBIT FIRE/HU?
Inhibit Fire/HU
No [0]
SOFTWARE
REVISION?

EURO 46, 162 & 280 Programming Manual
Page: 11
Choose Mode Programming
1. Press or to scroll to 'CHOOSE MODE'. Press
.
2. Press or to select the 'EOL Range' for all
wired inputs. Press .
3. Press or to select the 'EOL Mode' for all wired
inputs*. Press .
4. Press or to select the 'Input Response Mode'
for all wired inputs. Press twice to return to the
Engineer menu.
4.4 Install ZEMs
If any wired or wireless Zone Expander Modules (ZEMs) are installed on the EURO control panel, they
must be addressed in this function.
4.4.1 ZEM Address
Refer to 'System Overview' (page: 4) for how many wired/wireless ZEMs can be installed.
4.4.2 ZEM Installed
[0] No [1] ZEM8 / EURO37R (Wired ZEMs) [2] ZEM32WE (Wireless ZEMs)
4.4.3 Enter Location
The text entered here will be displayed on the LCD display if a fault occurs on the ZEM, so the
ZEM can be easily located or referenced. For example, the location text maybe "ZEM Kitchen",
"ZEM Loft" etc.
Install ZEMS Programming
1. Press or to scroll to 'INSTALL ZEMS'. Press
.
2. Press or to select the 'ZEM Address' . Press
.
3. Press or to select the 'ZEM8 or EURO37R' ,
ZEM32WE or No' to 'ZEM Installed'. Press .
4. Enter the location of the ZEM. This is so it is
referenced and will appear on the display if a fault
occurs. Press to return to ZEM addressing.
5. Press to return to the Engineers menu.
4.5 Wireless Device Control
If a wireless ZEM (EURO-ZEM32-WE) is installed on the EURO control panel, the learning (and
deleting) procedure for the wireless inputs and bells are performed in this function. It is
recommended that all wireless devices are learnt at the wireless ZEM before any
installation/mounting are completed. The signal strength plays an important part in maintaining a
reliable wireless system, refer to page: 31 for more information.
4.5.1 Control Inputs
'Control Inputs' learns and deletes wireless inputs. Refer to 'System Overview' (page: 4) for the
maximum wireless inputs and wireless input mappings.
4.5.2 Control Bells
'Control Bells' learns and deletes wireless Deltabell external sounders. A maximum of 2 wireless
bells may be learnt.
CHOOSE MODE?
EOL Range
4K7/2K2 [1]
EOL Mode
DR [1]
Input Response
100ms [01]
INSTALL ZEMS?
ZEM Address
[0]
ZEM Installed
No [0]
Enter Location
_

EURO 46, 162 & 280 Programming Manual
Page: 12
4.5.3 Programming Keyfob Buttons
'Program Keyfob Buttons' assigns actions to each buttons on the keyfob.
NOTE: Keyfobs are learnt in the Master Manager Menu in the function 'CHANGE CODES'. Refer to
the user manual (RIN1527).
[0] No action: Disables the button [1] Show Status: GREEN = Unset. RED = Set.
[2] Set Area: Sets the chosen area [3] Unset Any Area: Unsets any area on the system
[4] Latch Output: Latches an output (programmable) when the nominated button is pressed.
[5] Timed Output: Activates an output for a period of time (programmable in seconds)
[6] Personal attack: Activates a personal attack activation (programmed in Engineers only)
Wireless Device Control Programming: Learning Inputs
1. Press or to scroll to 'WIRELESS DEVICE CONTROL'. Press
.
2. 'Control Inputs' will be displayed. Press .
3. 'Learn Devices' will be displayed. Press .
4. Press or to select the input to learn and press .
5. Open the EURO control panel wireless device and press and hold
the 'LEARN' button until all LEDs flash
NOTE: The learn process is the same on all wireless contacts,
detectors, and sensors. Once the GREEN LED is flashing, the learn
process has been successful. Repeat the process above if the learn
procedure has not been successful.
Wireless Device Control Programming: Deleting Inputs
1. Press or to scroll to 'WIRELESS DEVICE CONTROL'. Press
.
2. 'Control Inputs' will be displayed. Press .
3. 'Learn Devices' will be displayed. Press .
4. 'Delete Devices' will be displayed. Press .
5. 'Delete All' will be displayed, press and enter '2000' to delete
all wireless peripherals, or press to delete individual inputs.
6. The inputs that are learnt will be displayed, press or to
select the inputs and press to delete it.
7. 'Input Deleted' will be displayed.
8. NOTE: Once a wireless input is deleted, the input type must be
set to 'unused' in the function 'CHANGE INPUTS' (page: 14).
LEARN
>5s
WIRELESS DEVICE
CONTROL?
Control Inputs?
Learn Devices?
Input 09
Available [09]
Learning...
Input Learnt!
WIRELESS DEVICE
CONTROL?
Control Inputs?
Learn Devices?
Delete Devices?
Input 01
Learnt [01]

EURO 46, 162 & 280 Programming Manual
Page: 13
Wireless Device Control Programming: Learning Bells
1. Press or to scroll to 'WIRELESS DEVICE CONTROL'. Press
.
2. 'Control Inputs' will be displayed. Press .
3. 'Control Bells' will be displayed. Press .
4. 'Learn Devices' will be displayed. Press .
5. Press or to select the bell (1 or 2) to learn and press .
6. Open the EURO control panel wireless Deltabell and press and hold
the 'LEARN' button until all LEDs flash
NOTE: Once the GREEN LED is flashing, the learn process has been
successful. Repeat the process above if the learn procedure has not
been successful.
Wireless Device Control Programming: Deleting Bells
1. Press or to scroll to 'WIRELESS DEVICE CONTROL'. Press
.
2. 'Control Inputs' will be displayed. Press .
3. 'Control Bells' will be displayed. Press .
4. 'Learn Devices' will be displayed. Press .
5. 'Delete Devices' will be displayed. Press .
6. 'Delete All' will be displayed, press and enter '2000' to delete
both wireless Deltabell external sounders, or press to delete
individual external sounders.
7. The external sounders that are learnt will be displayed, press 
or to select the bell and press to delete it.
8. 'Bell Deleted' will be displayed.
LEARN
>5s
WIRELESS DEVICE
CONTROL?
Control Inputs?
Control Bells?
Learn Devices?
Select Bell
Available [1]
Learning...
Bell Learnt!
WIRELESS DEVICE
CONTROL?
Control Inputs?
Control Bells?
Learn Devices?
Delete Devices?
Delete All?
Select Bell
Learnt [1]

EURO 46, 162 & 280 Programming Manual
Page: 14
Wireless Device Control Programming: Program Keyfob Buttons
1. Press or to scroll to 'WIRELESS DEVICE CONTROL'. Press
.
2. 'Control Inputs' will be displayed. Press .
3. 'Control Bells' will be displayed. Press .
4. 'Program Keyfob Buttons' will be displayed. Press .
5. Press or to select the user to learn and press .
6. Press or to select the button to be programmed and press
.
7. Press or to select the action of the button and press .
8. Select the area that the keyfob should be programmed in, press
.
NOTE: Keyfobs are learnt in the Master Manager Menu under
'CHANGE CODES'. Refer to the user manual (RINS1527).
4.6 Change Inputs
By default, all inputs are programmed as 'unused', therefore each input installed on the EURO control
panel must be programmed with the desired input type. To enable any programming the Engineer
menu must be exited.
4.6.1 Input Types
Refer to Appendix B (page 43), for all input type options.
Most commonly used input types:
[06] Intruder. [07] Final Exit. [08] Entry Route. [13] Day Alarm.
NOTE 1: If an alarm is triggered from an Entry Route input, it will store for 2 seconds before an
alarm is activated. If a Final Exit input is triggered within this time, the system will select entry
time, rather than an intruder alarm.
NOTE 2: Inputs may be automatically inhibited (omitted) at the time of reinstatement at the end
of confirmation time. Refer to 'Re-Arm Number' in 'CHANGE TIMERS' (page: 21).
4.6.2 Input Areas
The maximum number of areas differs on each EURO control panel, refer to 'System Overview'
(page: 4) for this information.
4.6.3 Input Attributes
The following attributes can be applied to any input:
Chime: When enabled the system loudspeaker(s) will ‘chime’ when an input is triggered whilst
the alarm panel is disarmed. Chime can be single – sounding once of follow – sounding while the
door is left open. NOTE: The chime can be turned On or Off in disarmed mode by pressing [c]
when all Final Exit inputs are closed.
Omittable: Enables the input to be manually omitted during the setting procedure or from the
user menu whilst the panel is disarmed.
Double Knock: If enabled, an alarm will be generated if this input is triggered twice within the
pre-programmed time window or if the input remains active for that period. The double knock
option does not work on Follow input type.
Dual Trip: An alarm will only be generated if 2 inputs one next to the other with a Dual Trip
attribute have been activated at the same time. This option is very useful for setting up outdoor
perimeter protection.
Normally Open: Both wired and wireless inputs are normally set to Normally Closed. This
attribute allows setting up the input as a Normally Open.
WIRELESS DEVICE
CONTROL?
Control Inputs?
Control Bells?
Program Keyfob
Buttons?
User [01]
Select Button
Lock [1]

EURO 46, 162 & 280 Programming Manual
Page: 15
Walk Test: The panel will not set if the user does not activate each detector with this attribute
after starting the setting timer. This is a way to prevent setting the system with masked or faulty
detectors.
Monitor Activity: This attribute works in conjunction with the NAT (Non Activity) timer. If a
detector has not been activated in during the NAT time the NAT output if programmed will be
activated. An event will be registered in the log too.
Special Log: Forces a log entry when the input is opened or closed, even when an alarm does
not result. May be selected to apply when a system is armed, when disarmed, or always.
Paired Input: For use in Grade 3 iD systems (or EoL inputs on peripheral devices fitted software
prior to version 5). Select to ‘YES’ for each of the two biscuits acting as the input. Fault Input:
Select to ‘YES’ for the biscuit acting as the ‘fault & anti-mask’ Paired With: For both biscuits
enter the input number with which each is paired.
Confirm Group: If one or more inputs are selected within the same confirm group, all confirmed
signals will be disabled. If confirm group is selected as ‘00’ the inputs are not part of any group.
If inputs are allocated to group 99 they will generate an alarm that results in an intruder
(unconfirmed) signal to an ARC. They will not under any circumstances generate a confirmed
signal, regardless of which group the input that selected the ‘unconfirmed’ alarm is allocated to.
4.6.4 Input Description
A name and location can be entered here. The name will appear on the display if an alarm has
occurred; the location is used for a more detailed reference if required.
Creating a Common Area
In some installations a ‘common’ area may be required. A common area is an area that only
arms, when other specific areas become armed.
Example: An entry and exit reception area in a building may only need to be armed if both the
offices and warehouse are armed.
If the office in Area A is armed, but the warehouse in Area B is still occupied, then the reception
would still need to be inactive so people would be able to leave the premises via the entry / exit
reception route.
One input can be allocated to one or more areas. In this example the inputs located in the
reception area will be programmed so that the reception inputs will be in Area A and Area B but
these inputs must have the Common input attribute programmed.
Area A: Office - Inputs = 3, 4, 5
Area B: Warehouse - Inputs = 6, 7, 8
Reception inputs – 1 and 2 are programmed into both Areas A and B, with the Common input
attribute programmed to both inputs.
The Reception Area inputs will now only become active if both Area A and Area B are both
armed.
Masking Response
When unset, a masking event will generate an audible “alert” that requires a response at the
keypad. There will be NO signal transmitted to the ARC. When set, a masking event will generate
an unconfirmed alarm but will NOT result in a confirmed alarm if paired with a normal activation
of the same detector. This harmonises with the requirement of EN50131-1 cause 8.4.5 and the
insurer’s preference expressed in BSIA Form 171.
Change Inputs Programming
1. Press or to scroll to 'CHANGE INPUTS'. Press .
2. Press or to select the input to program. Press .
3. 'Input Type' will be displayed. Press or to select the input
type or input the shortcut number (Refer to Appendix B (page 43))
for all input type options. Press 
4. 'Input Area' will be displayed. Select the Area's to be assigned to
the input and press .
5. 'Input Attributes' will be displayed. If any attributes are needed for
the input, press and press or to select between the
attribute enable/disable options and press to go to the next
attribute.
CHANGE INPUTS?
Input [01]
Input 01
Input Type [07]
Final Exit

EURO 46, 162 & 280 Programming Manual
Page: 16
6. 'Enter Name' will be displayed. Enter the name of the input and
press . This will be displayed if it is activated or when a fault
occurs.
7. 'Enter Location' will be displayed. Enter the location of the input
and press . This will be displayed if it is activated or when a
fault occurs after the name of the input has been shown.
8. Press or to select another input to program (01-66) or
press the key to return to the Engineer menu.
4.6.1 Shunt Inputs
A shunt group may consist of any number of inputs programmed as Intruder, Day Alarm and Entry Route
types. These must all be allocated in the same Area. NOTE: These will need to be programmed first.
The inputs in the shunt group/list will only activate after 10 seconds of the nominated shunt input. For
example, if input 1 is programmed as ‘Shunt Input’, and inputs 2 and 3 are programmed as “Day Alarm”,
then once input 1 has been opened, after 10 seconds inputs 2 and 3 become active. (Inputs 2 and 3 will
not become live after 10 seconds if either detector is in active).
Action Status Outputs
Shunt Input closed (shunted) Inputs within the shunt list are
inactive The ‘Follow Input’ output is live
Shunted Input triggered No response
Shunt Input opened (unshunted) -
The ‘Follow Input’ output clears. The
‘Shunt Fault’ output is live for 10
seconds.
After 10 seconds Inputs in the shunt list are active Indications off.
Shunt Input opened with an active
detector (attempting to unshunt) -
The ‘Follow Input’ output clears. The
‘Shunt Fault’ output pulses until the
shunt is reset or the input fault
clears.
Active input clears -
The ‘Shunt Fault’ output is live for 10
seconds. (Will not function correctly
on an ATE pin).
After 10 seconds Inputs in the shunt list are active Indications off.
Shunted input triggered (whilst not
triggered) Normal input response
(Note: depends upon the status of
the Area in which the shunt is
located).
Change Inputs Programming: Shunt Inputs
1. Press or to scroll to 'CHANGE INPUTS'. Press .
2. Press or to select the input to program. Press .
3. 'Input Type' will be displayed. Enter '18' for 'Shunt Input' Press

4. 'Shunt Inputs' will be displayed. Enter the inputs to include in the
Shunt List, after each input press . Each input will scroll on the
bottom line of the LCD display.
NOTE: Inputs programmed as 'Intruder, Tamper, Day Alarm or Entry
Route' cannot operate as a Shunt Input.
5. 'Input Area' will be displayed. Select the Area's to be assigned to
the input and press .
Input Areas
[ A ]
Input Attribtes?
Enter Name
_
Enter Location
_
CHANGE INPUTS?
Input [01]
Input 01
Input Type [18]
Shunt Input
Shunt Inputs?

EURO 46, 162 & 280 Programming Manual
Page: 17
6. 'Input Attributes' will be displayed. If any attributes are needed for
the input, press and press or to select between the
attribute enable/disable options and press to go to the next
attribute.
7. 'Enter Name' will be displayed. Enter the name of the input and
press . This will be displayed if it is activated or when a fault
occurs.
8. 'Enter Location' will be displayed. Enter the location of the input
and press . This will be displayed if it is activated or when a
fault occurs after the name of the input has been shown.
9. Press or to select another input to program or press the
key to return to the Engineer menu.
4.7 Assign Keypads/Readers
Any additional keypads or readers must be addressed correctly before enabling them in this function.
The EURO control panel keypad is automatically addressed as '00' on initial power up. Refer to the
installation manual (RINS1529) for more information.
4.7.1 Address
Address '00' is used for the first keypad installed on the EURO control panel.
NOTE: Each keypad has its own individual menu that programs the key-click volume, tag volume
and master volume. It will address a keypad, show the status of the keypad inputs (if
programmed), force the backlight on or off and the identification number of a tag (once a tag is
presented). The PA/Fire timer can be programmed. This menu also addresses the keypad.
To enter the keypad menu, press and hold the key until ‘SECURITY CODE’ is displayed, and
then enter ‘2000’. This function is also used to address the keypad.
4.7.2 Type
[0] Keypad. [1] Reader. [2] Not Used.
4.7.3 Reader is
If a tag reader is installed, the following options can be assigned:
[0] Set Point: Reader used for setting and unsetting.
[1] Ward Control: A reader can be used to create wards. For example: A keypad may control a
full area, but in the area you may wish to control certain inputs only.
[2] Access Control: If an access control system is installed then the reader must be
programmed as this type. The lock open time and door open time can be programmed (in
seconds).
[3] Unset Only: If the Reader is to be used as an unset device only, select this type.
[4] Entry Control: Used to lock/unlock doors. The external or internal reader can have
magnetic locks connected to them. This option is used in conjunction with ‘tag opens doors’ in
'SITE OPTIONS' page: 26. The lock open time and door open time can be programmed (in
seconds).
4.7.4 Set Point Sets
A “Setting Point” means that you can program the keypad / reader to set certain Areas only. This
is used in conjunction with the Areas allocated to a user code.
For example, if a user code is programmed to operate Areas ‘A’ and ‘B’, but the keypad / reader
is only programmed to Set Area ‘A’, then the system will set only Area ‘A’.
4.7.5 Set Point Unsets
An “Unsetting Point” means that you can program the keypad / reader to unset certain Areas
only. This is used in conjunction with the Areas allocated to a user code.
For example, if a user code is programmed to operate Areas ‘A’ and ‘B’, but the keypad / reader
is only programmed to Unset Area ‘A’, then the system will Unset only Area ‘A’.
Shunt Inputs[02]
Input 02
Input Areas
[ A ]
Input Attribtes?

EURO 46, 162 & 280 Programming Manual
Page: 18
4.7.6 Set Point In
The keypad needs to also be told which Areas it is operating “in”. For example, a keypad may
only be needed to operate in Area A, but other code users may use the keypad to quick Set other
Areas (such as a cleaner, director, caretaker etc). Therefore if Areas A and B are selected in the
previous options (Set point arms and disarms), but Area A only is selected in ‘Set point in’, then
Area B will quick set once a valid tag/code has been entered. To program Areas operating with
their programmed timer, then the Areas need to be entered into the “Set Point In” function.
4.7.7 Set Point Description
A name and location can be entered here. The name will appear on the display if an alarm has
occurred, the location is used for a more detailed reference if required. E.g. Name = Entrance
Keypad. Location = Hall
Programming Keypads: Assign Keypads/Readers
1. Press or to scroll to 'ASSIGN KEYPADS/READERS'. Press
.
2. Press or to select the address. Press .
3. 'Type' will be displayed. Press 0to select keypad.Press 
4. 'Set Point Sets' will be displayed. Select the area and repeat for
'Set Point Unsets' and 'Set Point In'. Press .
5. 'Set Point Description' will be displayed. Press to enter the
name and location if required.
6. 'Enter Name' will be displayed. Enter the name of the keypad and
press .
7. 'Enter Location' will be displayed. Enter the location of the keypad
and press .
8. Press or to select another device address to program or
press the key to return to the Engineer menu
Programming Readers for Set Point or Unset Only: Assign
Keypads/Readers
1. Press or to scroll to 'ASSIGN KEYPADS/READERS'. Press
.
2. Press or to select the address. Press .
3. 'Type' will be displayed. Press 1to select reader.Press 
4. 'Reader is' will be displayed. Press 0for 'Set Point' or press 3
for 'Unset Only' Press .
5. 'Set Point Sets' will be displayed. Select the area and repeat for
'Set Point Unsets' and 'Set Point In'. Press .
6. 'Set Point Description' will be displayed. Press to enter the
name and location if required.
7. 'Enter Name' will be displayed. Enter the name of the keypad and
press .
8. 'Enter Location' will be displayed. Enter the location of the keypad
and press .
9. Press or to select another device address to program or
press the key to return to the Engineer menu.
ASSIGN KEYPADS/
READERS?
Address
[0]
Type
Keypad [0]
Set Point Sets
[ A ]
Set Point
Description?
Enter Location
_
ASSIGN KEYPADS/
READERS?
Address
[1]
Type
Reader [1]
Reader is [0]
Set Point
Set Point Sets
[ A ]
Set Point
Description?

EURO 46, 162 & 280 Programming Manual
Page: 19
4.7.8 Ward Control
A reader can be used to create 'wards' which are sub-area's that work independently from the
assigned area.
Ward Inputs: Each ward may consist of any number of inputs, all of which must be allocated to
the same area. No input can be allocated to more than one ward. Final Exit input types cannot be
allocated to a ward and in the ward the setting/unsetting if the inputs is immediate without delay
timers. The ward can be either be operated by proximity tag, or by key (or other) switch wired
into the first input of the tag reader.
NOTE: The proximity tags for ward controls are programmed through the Master Manager menu
through the 'CHANGE CODES' options. The reader provides ‘Alarm’ and ‘Ready’ outputs dedicated
to that ward. It also provides relevant indications, including set/unset status, so these should
always be located adjacent to the controlling switch where used.
Auto Readmits: If this option is selected as ‘When Area Set’ then the ward control will always set
when the area in which is it located is set. If selected as ‘Never’ it will always require manual
setting from a programmed tag. The ward control must ALWAYS be unset manually. An
additional option is available in the ‘SYSTEM OPTIONS’ menu, to allow an Abort signal to be
generated by silencing an alarm at the Reader after alarm has been generated in the sub-area.
Ward Control By: A ward may be controlled by a tag or an input.
Action Status Notes
Normal (unset) status Detectors within Ward are inactive ‘Unset’ indication lit
Ward input triggered No response
Attempt to set Ward with input in
fault -
‘Fault’ LED flashes and
intermittent tone to indicate
‘cannot set’
Set Ward with no faults Ward sets (detectors live) ‘Unset’ indication goes out
Ward input triggered Alarm generated ‘Alarm’ LED lights, alarm tone
generated
Ward Controller unset Ward unsets ‘Unset’ indication lights
Valid code entered at a Keypad
whilst alarm running Alarm silenced Ward remains set.
Programming Readers for Ward Control: Assign
Keypads/Readers
1. Press or to scroll to 'ASSIGN KEYPADS/READERS'. Press
.
2. Press or to select the address. Press .
3. 'Type' will be displayed. Press 1to select reader.Press 
4. 'Reader is' will be displayed. Press 1for 'Ward Control'. Press
.
5. 'Ward Inputs' will be displayed. Enter a ward input and press .
Each ward input will be added to the list. Press once all inputs
have been entered.
6. 'Auto Readmits' will be displayed. Press or to select the
between 'When Area Set' or 'Never' . Press .
7. 'Ward Control By' will be displayed. Press or to select the
between 'Tag' or 'Input' . Press .
8. 'Ward Control Name' will be displayed. At default, the ward control
name is 'Device 01' which needs to be referenced when
programming codes/tags for the Ward Control in the Master
Manager Menu.
9. 'Enter Location' will be displayed. Enter the location of the keypad
and press .
10. Press or to select another device address to program or
press the key to return to the Engineer menu.
ASSIGN KEYPADS/
READERS?
Address
[1]
Type
Reader [1]
Reader is [1]
Ward Control
Ward Inputs [--]
Auto Readmits
When Area Set[0]
Ward Control By
Tag [0]

EURO 46, 162 & 280 Programming Manual
Page: 20
Programming Readers for Entry Control or Access Control:
Assign Keypads/Readers
1. Press or to scroll to 'ASSIGN KEYPADS/READERS'. Press
.
2. Press or to select the address. Press .
3. 'Type' will be displayed. Press 1to select the reader.Press 
4. 'Reader is' will be displayed. Press 2for 'Access Control' or press
4for 'Entry Control' Press .
5. 'Default Area' will be displayed if 'Entry Control' is selected. Select
the default area and press .
6. 'Lock Open Time' will be displayed. Enter the Lock Open Time in
seconds and press . (Max 255 seconds).
7. 'Door Open Time' will be displayed. Enter the Door Open Time in
seconds and press . (Max 255 seconds).
8. 'Access Control Description' will be displayed. Press .
9. 'Enter Name' will be displayed. Enter the name of the keypad and
press .
10. 'Enter Location' will be displayed. Enter the location of the keypad
and press .
11. Press or to select another device address to program or
press the key to return to the Engineer menu.
4.8 System Displays
This function programs the text display on the keypad for when the system is unset, or an area is set.
The Site Name reference is programmed here which must match the site name programmed on the
InSite software. There are options to enable or disable displaying when set, alarms, hold ups or
inputs.
4.8.1 Area Texts
This programs how each Area will be displayed. For example if 'Area A' is used to set the full
house this can be text as “Full House Set”. There is a maximum of 16 characters on the display.
4.8.2 Sign On Message
The Sign on Message is the main display on the top line in unset mode.
4.8.3 Site Name
The Site Name is used as a reference for the PC software if used - This is the EURO InSite PC
software, please refer to the installation manual (RINS1529) if used.
4.8.4 Display When Set / Display Alarms / Display HU’s / Display Inputs*
If ‘Display when set’ is enabled, then the Area Text will be displayed on the LCD keypad once the
system is fully set. If Display Alarms / HU’s are enabled, they will show any alarms that are
activated before a valid user code/tag is entered. If Display Inputs is enabled, any inputs
activated in day mode will be displayed.
NOTE: Must be set to NO to comply with EN50131-1
System Displays Programming
1. Press or to scroll to 'SYSTEM DISPLAYS'. Press .
2. 'Area A Text' will be displayed. Enter the text and press .
Repeat for all areas.
3. 'Sign on Message' will be displayed. Enter the text and press .
4. 'Site Name' will be displayed. Enter the text and press .
5. 'Display When Set' will be displayed. Press or to enable or
disable the function. Press . Repeat for 'Display Alarms',
'Display Hus', and 'Display Inputs'. Press to return to the
Engineer menu.
ASSIGN KEYPADS/
READERS?
Address
[1]
Type
Reader [1]
Reader is [4]
Entry Control
Default Level
[A ]
Lock Open Time
[005]
Door Open Time
[005]
SYSTEM DISPLAYS?
Area A Text
Full Set
Sign On Message
Enforcer