Pyronix Pcx 46 app User manual

RINS1772-1

PCX 46 Programming Reference

Page: 2

1. Contents Page

1. Contents Page ........................................................................................................................................ 2

2. Introduction ........................................................................................................................................... 3

2.1 Hybrid Integrated System with Automation Control ................................................................................. 3

2.2 Two-Way Wireless Technology .............................................................................................................. 3

2.3 User Automation Outputs..................................................................................................................... 3

2.4 SMS Text Alarm Notifications................................................................................................................ 3

2.5 System Remote Control with the HomeControl+...................................................................................... 3

3. Keypad Operation.................................................................................................................................... 4

4. The Engineer Menu .................................................................................................................................. 5

4.1 Navigating in the Engineers and User Menu ............................................................................................ 5

4.2 Entering The Engineer Menu (Default Engineer Code = 9999) ................................................................... 5

4.3 Exiting The Engineer Menu................................................................................................................... 5

4.4 Accessing the Engineers Menu on any external wired keypad .................................................................... 5

4.5 Saving Your Programming.................................................................................................................... 5

5. Engineer Menu ........................................................................................................................................ 6

5.1 Learn Wireless Devices? ...................................................................................................................... 6

5.1 Program Zones (Inputs)? ..................................................................................................................... 8

5.2 Zone Wiring? ....................................................................................................................................12

5.3 Add Zone Expander? ..........................................................................................................................12

5.4 Program Outputs?..............................................................................................................................12

5.5 Install Keypads and Readers? ..............................................................................................................15

5.6 Program Timers? ...............................................................................................................................17

5.1 Change Codes? .................................................................................................................................18

5.2 Volume Control?................................................................................................................................20

5.3 System Configuration - Options?..........................................................................................................20

5.1 System Configuration – System Displays...............................................................................................21

5.2 View Event Logs?...............................................................................................................................22

5.3 Engineer Tests?.................................................................................................................................22

5.4 Diagnostics? .....................................................................................................................................23

5.5 Communications? ..............................................................................................................................24

5.1 Options Up/Downloading? ...................................................................................................................26

5.2 Callback Menu? .................................................................................................................................27

5.3 Software Revision? ............................................................................................................................27

5.4 Factory Default? ................................................................................................................................27

5.5 Press A To Save & Exit Engineer Menu?.................................................................................................28

6. Adding External Wired Keypads ................................................................................................................28

7. Options Programmable Only From PC ........................................................................................................28

7.1 Auto Arm/Disarm Timers ....................................................................................................................29

7.2 Areas to Arm/Disarm .........................................................................................................................29

7.3 Programming Logic Gates ...................................................................................................................30

8. Faults and Troubleshooting ......................................................................................................................30

8.1 Device Fail / Active Faults ...................................................................................................................30

8.2 System Faults and Troubleshooting ......................................................................................................30

9. Event Types ..........................................................................................................................................34

10. Contact ID & SIA reported events ...........................................................................................................37

11. EN 50131 Terminology ..........................................................................................................................39

12. Access Levels.......................................................................................................................................39

13. Factory Defaults ...................................................................................................................................40

PCX 46 Programming Reference

Page: 3

2. Introduction

2.1 Hybrid Integrated System with Automation Control

The PCX 46 App is hybrid alarm system. It integrates the award winning Enforcer Two Way wireless

technology with 30 automation outputs and a host of high security features. The PCX 46 App is easy to

use and designed to communicate to you about any system activations via our HomeControl+

smartphone App notification messages. It can also send alarms to the Alarm Receiving Centre and

maintenance company.

2.2 Two-Way Wireless Technology

Using the wireless input expansion module RIX 32-WE, the PCX 46 App converts into a high security

wireless system taking full advantage of Pyronix’ innovative wireless technology using the Pyronix High

Security Wireless Encryption Protocol. This module also allows the access to all Enforcer system 2-way

wireless peripherals.

Always Alert: The two way wireless movement detectors are fully operational when the system is

armed, making your system more secure, compared to other wireless systems, where devices are

disabled for up to five minutes after every activation to save battery, therefore compromising your

security.

Battery Monitoring/Saving: The Enforcer wireless peripherals use advanced technology to preserve

the battery life of each wireless device. However, the system informs you when a battery needs

replacing a month in advance before the device stops working. This key feature gives you enough time

to change the battery in the specific device. Other wireless alarm systems may not give you a low

battery warning signal, meaning that devices could stop working, leaving your environment unprotected.

High Security Encryption: The wireless protocol is encrypted with 128 bit making it practically

impossible to replicate or copy its wireless peripherals. It also uses an intelligent wireless jamming

detection technology.

User Friendly Keyfobs: Up to 32 wireless keyfobs can be added to the PCX 46 App system. Each

wireless keyfob has its own user ID which can be reported to the ARC and user mobile phone. It is

possible to allocate different functions to each keyfob such as arming / disarming different areas,

activating the automation outputs to control external devices such as gates, requesting system status,

and activating panic alarms giving you total control of your system. It shows you the system status using

a 3 colour LED:

System armed: When the system is armed a RED LED will illuminate momentarily.

System disarmed: When the system is disarmed a GREEN LED will illuminate momentarily.

System fault: When the system is in fault condition an AMBER LED will illuminate.

2.3 User Automation Outputs

The PCX 46 App has ability to operate up to 30 user automation outputs that give you the option activate

gates, lights, sprinklers, etc. via your keypad, wireless keyfob or smart phone app.

2.4 SMS Text Alarm Notifications

When your system is activated it will notify you via SMS text messages in real time. For example,

notification that your child has returned home from school safely or notification of a leakage of water in

your property etc.

2.5 System Remote Control with the HomeControl+ App

The PCX 46 App system can be remotely controlled using the HomeControl+ smartphone App. It allows

you to arm and disarm the PCX 46 App, check the system status and bypass zones/inputs. It also allows

you to activate remotely up to 30 devices such as gates, lights, sprinklers and more.

PCX 46 Programming Reference

Page: 4

3. Keypad Operation

Button keys:

The following alpha-numerical buttons are used

a= Selects Area A, Upper case /lower case, Exit engineers menu.

b= Selects Area B

c= Selects Area C, Clears letters / adds a space

= Selects Area D

= Press to Enter Manager Mode

= Press for 2 sec to generate Fire alarm

p= Press for 2 sec to generate PA alarm

[= moves cursor left

]= moves cursor right

On the PCX 46 App it is possible to write personalized titles for the following:

- Zone/Inputs, Zone/Input Number, Location

- Area Names

- Site Name

- Keypad/Reader, Keypad Number, Location

- Zone/Input and Output expander location descriptions

- User Names

The PCX 46 App incorporates a predictive text feature (T9 type). For example, if you enter ‘B’ ‘Bedroom’

will be displayed. If the word that you require doesn’t appear on the LCD display, just type the word letter

by letter. To type a word, press the relevant button the appropriate number of times – e.g. for the letter

‘k’ press the 5key two times, or for the letter ‘s’ press the 7button four times. For punctuation marks,

press the 1button.

PCX 46 Programming Reference

Page: 5

4. The Engineer Menu

The system is programmed from the Engineer Menu. To enter the Engineer Menu the panel must be fully

disarmed state. Whilst in Engineer Mode all tamper alarms (including case tamper), will be disabled.

4.1 Navigating in the Engineers and User Menu

x= “NO” - Press to move forward when in Engineer or Master Manger mode

b= “BACK” - Press to move backward when in Engineer or Master Manger mode

t= “YES” - Press to enter in a submenu or option when in Engineer or Master Manger mode

t= Press to move from one option into another option while in a submenu

a= Press to quick exit the Engineer Menu from any main menu (written in capital letters)

c= “CANCEL” - Press to move back from one programmable option to the previous option.

4.1.1 Main Menus and Sub Menus

You are in a main menu item if:

 The maintenance LED is flashing slowly

 The menu item will be in upper case letters

with a question mark (?).

You are in a sub menu item if:

 The maintenance LED is flashing rapidly

 The menu item will be in lower case letters with

a question mark (?).



In order to navigate in the menu system one has to answer the questions in the main and sub menus.

For example, if the question is “LEARN WIRELESS DEVICE”. Pressing twill bring you in the sub-

menu “Learn Zoness?” Pressing twill take you to the programmable options of this submenu.

Pressing xwill take you out of the individual option, will move you up from one sub-menu to the

next sub-menu or back to the main menu.

NOTE: For your security, the keypad becomes disabled for 90 seconds after 16 incorrect key-presses,

or after 6 attempts to present invalid tags. It will subsequently be disabled again after 7 further

incorrect key-presses or after another invalid tag is presented. Once a correct code or tag has been

registered, the keypad is returned to normal operation. PIN code entry must be completed within 60

seconds or it will count as an invalid code being used.

4.2 Entering The Engineer Menu (Default Engineer Code = 9999)

Access maybe denied if: 1) One or more areas are armed.2) The Master user has disabled the access of

the Engineer Menu from “Allow Engineer Menu” in the Master Manager Mode. If this is the case

‘Authorization required’ will be shown on the display. After entering the Engineer code 9999 (default

code) the first option that is shown will be: Arm System? This option will enable the Engineer to Arm

the panel once maintenance work is finished. The system can also be disarmed by the engineer if it was

armed with an engineer code. Press tto arm the system or press xto enter the Engineer Menu.

When in Engineer Menu, the fault () LED will flash and high pitch tone will be generated regularly.

4.3 Exiting The Engineer Menu

On completion of programming, the system can be returned back to disarmed mode by pressing the a

button from any main menu option (represented in capital letters) or pressing ton the menu option

‘PRESS A TO EXIT & SAVE ENG MENU?’.

4.4 Accessing the Engineers Menu on any external wired keypad

It is possible to access the Engineer Menu on any keypad that is part of the system. If you are in the

Engineer menu in keypad address 0, the other keypads will display ‘system busy’. To access the

Engineer menu on a different keypad, press the bbutton on the relevant keypad.

4.5 Saving Your Programming

Any programming done in the engineer or user mode will not be saved on the system until the Engineer

or User menu have been exited.

PCX 46 Programming Reference

Page: 6

5. Engineer Menu

Please refer to the Programming Manual for this chapter. The meaning of every option presented in the

Programming manual is explained here in detail.

5.1 Learn Wireless Devices?

This function should only be used if a PCX-RIX32-WE (Enforcer wireless expander) is connected to the

PCX 46 App. Please see the Installation Reference Manual for connecting this expander.

This menu learns or deletes wireless devices for the zones/inputs and bells/sirens.

NOTE: The keyfobs are learned and programmed from the Master Manager menu.

5.1.1 Learn Zones/Inputs?

Learn Devices?

This menu allows you to start the procedure of learning wireless zones/inputs onto the system.

Choose Zone/Input

Use this menu to choose which zone/input on the system you wish to learn. ‘Learnt’ will be displayed

if a device is already learnt, or ‘Available’ will be displayed if it is not.

Choose Zone/InputLearning…

1) Take the wireless device, and open the casing

2) Remove the plastic insulation between the battery and terminal.

3) If a Device is not learned = The Green and Red LEDs on the Device will flash alternately.

4) Press and hold the ‘learn’ button on the Device = The 3 LEDs will start cycling.

5) Release the ‘Learn’ button = ‘Zone Learnt’ will be displayed and confirmation tone on the panel will

be emitted.

6) If a zone/input has already been learnt, ‘Zone learnt already’ will be displayed.

Example: The image below shows how to learn an MC contact. The same procedure is followed for

other zones/inputs and sensors. Please note if smoke or carbon monoxide sensors are learnt, they will

just include one multicolour LED.

Delete Devices

Already learnt zones/inputs may be deleted from this menu.

Delete All Enter Code

To delete all wireless zone/input devices enter ‘2000’ (this is the PCX 46 App Security Code). “Please

wait” will be displayed while the PCX 46 App deletes ALL the wireless devices learnt on the

zone/inputs.

Choose Zone/Input to Delete

This option allows you to delete only a specific wireless device learnt to a zone/input. Any

zones/inputs that display ‘learnt’ can be deleted. “Please wait” will be displayed while the PCX 46 App

deletes the wireless device. Return to this process to delete more devices.

5.1.2 Learn Bells?

Learn Devices

Entering this menu allows you to start learning wireless bells onto the system

LEARN

>5s

PCX 46 Programming Reference

Page: 7

Select Bell

Use this menu to choose which bell on the system you wish to learn. ‘Learnt’ will be displayed if a bell

is already learnt, or ‘Available’ will be displayed if not.

Select BellLearning…

1) Open the bell

2) Plug the battery connector into the battery terminal.

3) If a Device is not learned = The Green and Red LEDs on the Device will flash alternately.

4) Press and hold the ‘learn’ button on the Device = The 3 LEDs start cycling around.

5) Release the ‘Learn’ button = ‘Bell Learnt’ will be displayed and confirmation tone on the panel will

be emitted.

If a Bell has already been learnt, ‘Bell learnt already’ will be displayed.

Delete Devices

Already learnt bells may be deleted by entering this menu.

Delete All Enter Code

To delete all wireless Bells enter 2000 security code. “Please wait” will be displayed while the

PCX 46 App deletes them.

Choose Bell to Delete

This option allows you to delete only a specific wireless Bell learnt. Any Bells that display ‘learnt’ can

be deleted. “Please wait” will be displayed while the PCX 46 App deletes the wireless Bells. Return to

this process to delete more devices.

Learn Keyfobs Procedure

The keyfobs are learnt and deleted from the Master Manager menu.

Learn Keyfobs

1) Enter Master Manager Menu (Default Master Code = 1234).

2) Scroll to the “LEARN USER CODES KEYFOBS & TAGS” option.

3) Choose a code to allocate the keyfob to.

4) If a keyfob, code or tag are not learnt the space, between brackets will be empty.

5) If a keyfob, code or tag is learnt between the brackets will be shown [******].

6) Press and hold any of the keyfob buttons for 5sec.

7) A confirmation tone will be emitted and keyfob will be shown on the display.

Proceed with the programming of the keys shown next.

Delete Keyfobs

1) Enter Master Manager Menu (Default Master Code = 1234).

2) Scroll to “LEARN USER CODES KEYFOBS & TAGS” option.

3) Choose the keyfob to delete = between the brackets will be shown [******].

4) Press c. Between the brackets will be shown [ ] to confirm the deletion.

LEARN

>5s

PCX 46 Programming Reference

Page: 8

5.1 Program Zones (Inputs)?

By default, all zones/inputs are set to ‘unused’. Before programming, identify zone/input type required:

No Zone/Input

Type Operation

0 Unused Zone/Input is disabled.

1 Fire Active at all times. Audible Response: Differentiated Internal sound. Pulsed

external sound.

Communicator: ‘Fire’ signal

2 Gas Active at all times. Audible Response: Full external + Internal sound.

Communicator: ‘Gas’ signal

3 PA#Active at all times. Audible Response: Differentiated Internal sound. Full

external sound.

Communicator: ‘Personal Attack’ and ‘Zone/Input PA’ signals

4 Silent PA#Active at all times. Audible Response: None

Communicator: ‘Personal Attack’ and ‘Zone/Input PA’ signals

5 Tamper When disarmed: Audible Response: Internal only.

Communicator: ‘Tamper’ signal.

When armed: Audible Response: Full external + Internal sound.

Communicator: ‘Tamper’ signal.

6 Instant Active when armed: Audible Response: Full external + Internal sound.

Communicator: ‘Burglary’ signal

7 Entry Delay1#$ Active when armed: Initiates entry timer 1 when door open. If system not

disarmed before entry time expires then:

Audible Response: Full External + Internal sound.

Communicator: ‘Burglary’ signal

NOTE: See type 43 for Entry Delay2

8 Follow$Active when armed, except during entry time. (Acts as an instant zone/input

if an Entry Delay zone/input hasn’t been activated beforehand)

Audible Response: Full external + Internal sound.

Communicator: ‘Burglary’ signals.

11 Push To Arm Active during exit time, to complete arming procedure. No audible or

communicator response. Panel will communicate a final armed event once

the Push to Arm button has been pressed.

NOTE: May be used to act as ‘doorbell’ by use of ‘chime’ zone attribute.

Example: Wire the Door Bell button to the zone/input. Enable “Push to Arm”

option from “EXIT MODES”, add a “Push to Arm” zone/input type to the

zone/input and enable the “Chime” attribute for it.

Enter user code, the panel starts arming. Exit the building and close the

door. Press the Bell button. The system will arm. If pressing the Bell button

while the panel is in any other condition the Chime will sound.

12 Switcher Active at all times in armed and disarmed modes. No audible or

communication alarms will be created.

When activated it can trigger associated output for switching external

equipment. If the “Special Log” attribute is enabled for this zone/input an

SMS message will be sent each time the zone/input is activated.

Example:

This kind of zone/input type can be used to control CCTV. The concept is

that when a switcher zone/input type is activated, there is an output

associated with it following that zone/input (the most used solution is the

use of output type – 0035). The switcher zone/input is connected to a

detector located next to a CCTV camera and the output is connected to a

video recording / transmitting equipment.

If the detector is activated in armed or disarmed mode then the recording or

transmission will start.

13 24 Hour When armed: Audible Response: Full External + Internal sound;

Communicator: ‘24hr Alarm’ signal.

When disarmed: Audible Response: Full External + Internal sound;

Communicator: ‘24hr Alarm’ signal.

PCX 46 Programming Reference

Page: 9

15 Sub Area

Control

Active when armed or disarmed. Communicator: Sub-area Armed/Disarmed

event (CID 402/401). Sub Area may be armed or disarmed by proximity tag

or zone/input where a keyswitch can be wired. To each sub area can be

allocated a number of zones/inputs creating the sub-area configuration.

16 Fault Active when armed or disarmed: Audible Response: internal sounder.

Communicator: Fault event.

If armed only: Activates ‘Global Fault 1’ output type.

If disarmed or armed: Activates ‘Global Fault 2’ output type.

Note that the ‘Technical Fault’ output type is triggered every time a fault is

active including when the fault zone/input type is active.

17 Arming Control Active during arming procedure: No audible or communicator response.

Prevents system being armed whilst the zone/input is in an active state.

18 Shunt Active at all times: No audible or communicator response.

It is possible to associate zones/inputs to the shunt zone/input. It normally

is connected to a key-switch (or equivalent) and when On or Off it shunts or

un-shunts the zones/inputs assigned to it. Associated outputs are available

to follow this zone/input type.

Creating a Shunt Group: A shunt group may consist of any number of

zones/inputs programmed as Instant, Tamper, 24hr and Follow types. These

must all be allocated in the same area.

NOTE: These zones/inputs will need to be programmed before allocated to

the shunt zone/input.

The zones/inputs in the shunt group/list will only activate after 10 seconds

of the nominated shunt zone/input.

Example: If zone/input 1 is programmed as ‘Shunt zone’, and zones/inputs

2 and 3 are programmed as “24hr”, then once zone/input 1 has been

opened, after 10 seconds zones/inputs 2 and 3 become active.

Action 1: Shunt Zone/Input closed

Status: Zones/Inputs within the shunt list are Shunted ( Disarmed)

Outputs: ‘Follow Zone/Input’ PGM output On

Action 2: Shunt Zone/Input opened

Status: After 10 seconds zones/inputs in the shunt list are going to activate,

i.e. become Un-shunted (Armed)

Outputs: ‘Follow Zone/Input’ PGM output OFF. The ‘Shunt Fault’ PGM output

is on for 10 seconds.

Action 3: Shunt Zone/Input opened with active detector from the shunt list

Status: After 10 seconds zones/inputs in the shunt list are going to activate,

i.e. become Un-shunted (Armed)

Outputs: ‘Follow Zone/Input’ PGM output OFF. The ‘Shunt Fault’ (type 36)

PGM output pulses until the detector closes.

19 Disarm Only* Active when armed: Accepts zone/input from keyswitch (or equivalent) to

disarm the area(s) assigned to it.

20 Keyswitch

Latched*

Accepts zone/input from keyswitch (or equivalent) to arm/disarm the area

assigned to it. Arming includes normal exit time, etc. Requires latching

switch action. Normal operation is open circuit to arm the system, and close

circuit to disarm the system.

21 Entry Shock Active when system armed: This zone/input type is advised to be used in

conjunction with an Entry Delay input. The Entry Delay input is a door

contact on the initial entry door, and the Entry Shock zone/input is a non-

latching shock sensor fitted to the door frame in the vicinity of the lock. If

the door is forced a Burglary alarm will be generated immediately.

22 Line Fault Active when fail. This zone/input type is used to detect external

transmission equipment line fail (output). If activated will give a line fault

alarm, and will signal telecom line fault on expiry of line fault timer. It can

be used in conjunction with CCTV input (type 39)

23 Keyswitch

Pulsed*

Accepts zone/input from keyswitch to arm/disarm the area(s) assigned to it.

Requires momentary action switch to toggle arm/disarm state.

Note that Grade 1 operation only allows arming from the push button, but

requires means to abort arming (not to disarm)

PCX 46 Programming Reference

Page: 10

29 Interior This will work the same as an instant type zone/input, the only difference is

that when CID reporting is programmed then any inputs that are

programmed as Interior will report CID event 132.

32 Flood This zone/input type will work as a 24hr input, any zones/inputs that are

programmed for Flood will activate the external siren and will report CID

event 113.

39 CCTV Active at all times: No audible alarm or communicator response.

The CCTV zone/input should be connected to an external detector located

next to a CCTV camera. An output can be programmed to follow this

zone/input and the output should be connected to a CCTV recording,

transmission or other device. A zone/input programmed as “Line Fault”

(type 22) should also be connected to an output of the CCTV transmission

Device. If the CCTV transmission line has been cut or missing the ‘Line

Fault’ zone/input will activate. Following to this at each activation of the

CCTV zone/input the panel will signal CID events for ‘Silent Burglary’ and

Line Fault. No audible alarm will be created. If the Line Fault is not active it

will just log the activations of the CCTV zone/input into the event log.

40 Perimeter This will work the same as an instant type zone/input, the only difference is

that when Contact ID reporting is programmed then any zones/inputs that

are programmed as Perimeter will report Contact ID event 131.

41 Patrol / Keybox This zone/input type will work similarly to a switcher zone/input, it does not

trigger an alarm but will report Contact ID event 250 and is also a useful

zone/input type when an output is required to follow the Keybox type zone.

42 Medical This is a 24 Hrs type zone/input it will activate the external sounder and

report a Contact ID event 100.

43 Entry Delay 2$Any zone/input programmed as Entry Delay 2 will act as zone type 07, but

the associated entry timer will use Entry Timer 2, rather than Entry Timer 1.

#These zone/inputs cannot be bypassed.

*Use of zones/inputs 19, 20 and 23 will make the system unable to comply with EN50131-1 Security

Grade 2 or 3.

$ Ensure that these zones/inputs are used on an entry/exit route

Choose Zone/Input

Choose an input to program.

Zone In Area

Enter the areas you would like the input to operate in.

Common Zone

In certain situations, a ‘common’ area may be needed. A common area is an area that only arms if

other specific areas are armed.

Example: A reception in a building will only need to be armed if the offices and warehouse are armed.

If the office is armed, but the warehouse isn’t, then the reception would still need to be inactive so

people would be able to leave the premises. One zone/input can be allocated to one or more areas.

In this example the zone/inputs located in the reception area will be in the offices and warehouse

areas and have the common attribute activated.

Area A: Office – Zones/Inputs 1, 2, 3, 4 and 8. Area B: Warehouse – Zones/Inputs 5, 6, 7 and 8.

Zone/Input 8: The detector connected to this zone/input is going to be the zone/input located in the

Reception and is common to Area A and Area B. Zone/Input 8 will only be active if the Area A and

Area B are both armed. If one of them is disarmed then zone/input 8 will not be active either.

5.1.1 Zone Attributes?

No Attribute Operation for both wired and wireless inputs

1 Chime When enabled the system loudspeaker(s) will ‘chime’ when an input is

triggered whilst the alarm panel is disarmed. Chime can be single –

sounding once of follow – sounding while the door is left open. NOTE: The

chime can be turned On or Off in disarmed mode by pressing [c] when all

Entry Delay inputs are closed.

2 Allow

Bypass

Enables the input to be manually bypassed during the arming procedure or

from the user menu whilst the panel is disarmed.

PCX 46 Programming Reference

Page: 11

3 Double

Knock

If enabled, an alarm will be generated if this input is triggered twice within

the pre-programmed time window or if the input remains active for that

period. The double knock option does not work on Follow input type.

4 Cross

Zoning

Alarm will only be generated if 2 inputs one next to the other with

Combined Input attribute have been activated at the same time. This option

is very useful for setting up out door perimeter protection.

5 Normally

Open

Both wired and wireless inputs are normally set to Normally Closed. This

attribute allows setting up the input as a Normally Open.

6 Mask Test The panel will not arm if the user does not activate each detector with this

attribute after starting the arming timer. This is a way to prevent arming

the system with masked or faulty detectors.

7 Activity

Zone

This attribute works in conjunction with the NAT (Non Activity) timer. If a

detector has not been activated in during the NAT time the NAT output if

programmed will be activated. An event will be registered in the log too.

8 Special Log

(SP)

Forces a log entry when the input is opened or closed, even when an alarm

does not result. May be selected to apply when a system is armed, when

disarmed, or always.

9 Swinger

Limit

This attribute limits the number of times that a zone/input can signal an

event. For example if a window is left open and keeps swinging in the wind

you could set it to only signal an event up to 10 times. This limit attribute

will be reset for the associated zone/input, if another zone/input on the

system activates after this limit has been reached.

10 Inertia

Zone

If this function is enabled, all inputs will operate as “inertia”. Please note

that only PCX-RIX8i input expanders can be used with this function. Inertia

operates by determining the gross attack and pulse count of the force. For

example:

Gross Attack = 4 m/s. Pulse Count = 3. The input will activate after sensing

3 “knocks” near the area where the shock is installed (each pulse is kept in

memory for 15 seconds).

5.1.2 Input Description?

2 text labels can be associated to each input:

Zone Location: Here should be written the meaning of the zone/input. There are 14 characters

available for this label.

Example: Zone Number = Zone 01; Zone Name = Living Room. In case there has been a tamper

alarm on a zone/input the SMS alarms will show: ‘Zone 01, Living Room, Tamper Alarm’. On the

display will be shown: 01-Living Room, Tamper on Zone. Meaning: Tamper alarm on Zone 01 that is

the Living Room.

Enter Number: Best practice is to write the Zone/Input Number (Zone 01, Zone 02 and so on) on this

label. This label will be shown in the event log, following alarms, and reported in the SMS alarms as a

reference point. There are only 7 characters available for this label.

Manually Bypassing Zone/Inputs Procedure

Method 1: Whilst the system is arming, press the tkey to bypass zones/inputs.

Method 2: Enter user menu and from the “Bypass Zones” option bypass the zones/inputs as required.

Automatic Bypassing Zones/Inputs Procedure

Zones may be automatically bypassed when the panel auto re-arms if this option is enabled in the

system options.

PCX 46 Programming Reference

Page: 12

5.2 Zone Wiring?

The end of line programming for all zones/inputs on the PCX 46 App can be selected from the below

choices and are applied to all wired zones/inputs:

5.2.1 Choose EOL Range

[0] 1K/1K* (1K Alarm: 1K, Tamper: 1K)

[1] 4K7/2K2* (Alarm: 4K7, Tamper: 2K2)

An asterisk (*) indicates the single end of line value. For example, 4K7/2K2* means the 2K2 is the

single end of line value. Please note, when using a RIX8i only the 1K/1K can be used.

5.2.2 Choose EOL mode

This option is used to program single or double end of line mode of all wired inputs.

[0] Single End of Line (SEOL)*. [1] Double End of Line (DEOL)

5.2.3 Zone Response

This option selects the time that an zone/input must be open before the PCX 46 App responds to

activations. The response time can be programmed from 100ms (0.1 seconds) to 3000ms (3 secs).

NOTE: To comply with EN50131-1 ensure the response time is set to 400ms.

5.3 Add Zone Expander?

A maximum of 4 x wired zone expanders or 1 x wireless input expander can be installed on the

PCX 46 App.

NOTE: Wireless or wired must be chosen accordingly in the menu.

5.3.1 Exp Address

Select the address of the ZEM you wish to enable (Address 0-3). NOTE: If a PCX-RIX32-WE (Enforcer

wireless expander) is installed, each address will enable 8 wireless zones/inputs on the expander. See

the Installation Reference for more information.

5.3.2 Exp Installed

Enables the Wired Expander or Wireless RIX that has been installed. 2= Wireless / 1= Wired / 0= No

5.3.3 Zone Description

The description text is stored for reference on later maintenance visits i.e. “GROUND FLOOR”. For

information on how to use predictive text, please see page 4.

5.4 Program Outputs?

This option enables the programming of the outputs on the following Devices:

5.4.1 Panel Outputs?

These are the outputs on the control panel itself. There are 3 outputs: O/P (relay), Strobe and Bell.

This also includes the 9 ATE outputs that are enabled when a loom is connected to the board (please

see the Installation Reference manual).

5.4.2 Exp Outpus?

These are the outputs that are located on the zone/input expander module(s) if connected.

5.4.3 O/P Module O/Ps?

This option enables the addition of wired ROX modules to the PCX 46 App.

5.4.4 Keypad Outputs?

Allows the programming of the output options for the output located on the wired keypads.

5.4.5 Reader Outputs?

Allows the programming of the output options for the outputs located on the wired readers.

5.4.6 User Outputs?

These outputs are used for creating automation control for Devices. The user can control them

remotely from the user menu on the keypad. The automated user outputs can be programmed either

latched or pulsed.

NOTE: The O/P Outputs polarity cannot be inverted. Only the ATE outputs can.

PCX 46 Programming Reference

Page: 13

No. Output Type Active Restore

0000 Not Used

0001 Fire At fire alarm activation When a valid code is entered

0002 PA Any At personal attack activation When a valid code is entered

0003 Burglary Any At burglary alarm from any area At first valid code entry

0004 Final Arm All When ALL areas are armed At code entry to disarm

0005 Open After Alarm

(Abort)

When system is silenced after ‘burglary’

alarm has been activated

After 2 minutes

0007 Tamper Any Tamper alarm in any area At code entry to silence

0008 Duress Any At a Duress alarm in any area When a valid code is entered

0009 PA Device Any At alarm on a PA input only from any

area. (This does not include the keypad

PA)

When a valid code is entered

0010 Gas At gas alarm When a valid code is entered

0011 Arm Fail Pre-set time after start of exit time, if

exit procedure is not complete

At code entry to rearm

0012 Entry Deviation When deviation from entry route occurs,

during entry time

At code entry to disarm

0013 System Ready Any When any of the inputs but the Entry

Delay and Follow are closed

If fault exists, and after final arm

0014 Bell Any After alarm in any area When alarm silenced or when siren

timer expires

0016 Strobe Any After alarm in any area When disarmed or when strobe timer

expires

0017 Bypass Rearm Any When inputs are bypassed at rearm in

any area. Turned on after 1st alarm if

active when rearmed

When system disarmed

0018 Burglary Any At Burglary alarm in any area At code entry to silence

0019 Ready All When all inputs but the Entry Delay and

Follow are closed

If fault exists, and after final arm

0020 Exit Starts All At start of exit time to arm LAST area At disarm FIRST area (i.e. no longer

fully armed)

0021 Exit Starts Any When exit time starts to arm FIRST area At code entry to disarm LAST area

0022 Final Arm Any When ANY area has been armed At code entry to disarm LAST area

0023 Strobe if Arm Fail Works similar to output 016, but also fires if the arm fail timer expires.

0024 Unable to Arm This output turns on for 5 seconds when the system is disarmed via a keyswitch

input (either pulsed or latched keyswitch)*

0025 Keyswitch Disarm Output activates when an arming procedure is completed with inputs bypassed.

0026 Arm with Bypass Active when the system is armed with an input bypassed.

0027 Pulsed Burglary Any Active when burglary alarm is triggered, but deactivates once the Pulsed

Intruder timer has expired (see Program Timers).

0028 Power Fault Active during low volts and battery faults. Restores at code entry after fault

cleared.

0031 Entry Active during any Entry time

0032 Exit Active during any Exit time

0033 Entry / Exit Active during any entry or exit time

0034 Lights When exit or entry timer starts 20 seconds after arm/disarm

procedure completed

0035 Follow Zone/Input Active when a specific input number has been activated. It allows the following

options to be programmed:

Follow Type (Follow, Timed, Latched, Code Reset);

Follow What (Input, Shunt List, Sub-Area, Area);

Follow When (Always, When Armed, When Disarmed);

Input to Follow (between 1 to 64)

0036 Shunt Fault This input activates if someone tries to shunt an input group where some of the

inputs allocated to this group are open.

0037 Restore 1 At code entry to arm. The normal state

of this input is 0v and it changes to 12v

when activated.

After 3 seconds

0038 Restore 2 Activates whenever an additional area is

armed. The normal state of this input is

0v and it changes to 12v when activated.

When disarmed

0039 PIR Latch 1 When armed (and in Walk Test) At alarm, or when disarmed

0040 PIR Latch 2 This is the inverse polarity to

PIR Latch 1

At alarm, or when disarmed

PCX 46 Programming Reference

Page: 14

0041 AC Mains Good Output showing the 230v mains supply is present

0042 PIR LED Enable This output activates during walk test

0043 Follow Test Output will activate only when tested from the Engineer menu ‘Test Outputs’ in

the ‘Engineer Tests’. This output can be used as additional facility for testing the

operation of a Bell. An output programmed to one of these configurations (43 &

44) may be used to trigger a relay to break the hold-off connection to the Bell –

or even to provide the hold-off directly.

0044 Off During Test Output is normally active and will deactivate only when tested from the Engineer

menu ‘Test Outputs’ in the ‘Engineer Tests’.

Same as 43 but opposite activation.

0048 Walk Test This output is active during walk test, and will only deactivate when all detectors

have been tested

0049 Detector Masked If any detector goes into ‘mask’

condition the output will activate

When masking fault clears

0050 Follow 24 Hour If any input programmed as ’24 Hour’

activates

When input is restored

0051 Line/GSM Fault When Telephone or GSM Line Fault is

presented

When fault clears

0052 AC Mains Fail After pre-set time without mains power On restoration of mains

0053 Battery Fault When battery disconnected or load fail

detected

At next valid code entry

0054 Low Volts When less than 11.2v is presented. When fault clears

0055 Global Fault 1

(Grade 2)

Activates if any fault occurs only when

system is armed

When all faults cleared

0056 Global Fault 2

(Grade 3)

Activates if any fault occurs at any time When all faults cleared

0057 German Relay For future development. Do Not Use.

0058 Guard Code Used When ‘guard’ code used on the system After 60 seconds

0059 Engineer Access When entering Engineer Mode When leaving Engineer Mode

0060 Follow Power Up At power up Live for 45 seconds

0063 Test UK STU Activates when a test call is sent When test completed

0064 Pre RM Service Activates 1h before the RM Service call When test completed

0065 Zone/Input Fault

Activity

Activates when there is no activity on a

zone/input in the end of the “Activity

Timers” in Change Timers.

When there is activity.

0066 Digi Pin Not Used Makes the Digi/ATE pin 5V or 0V depending on whether ATE outputs are inverted

0067 Follow Chime Active while a Chime signal is created on the panel

0170--

0199

User Defined 01-30 The user outputs are used for user automation to control external Devices. They

can be controlled via the keypad from the used menu and can be programmed

as latched or timed (1 to 99 sec).

0202 PA A (As 0002 for Area A ) 0213 System Ready A (As 0013 for Area A )

0203 Burglary A (As 0003 for Area A ) 0214 Bell A (As 0014 for Area A)

0204 Final Arm A (As 0004 for Area A ) 0216 Strobe A (As 0016 for Area A )

0207 Tamper A (As 0007 for Area A ) 0217 Bypass on Rearm A (As 0017 for Area A )

0208 Duress A (As 0008 for Area A ) 0218 Burglary (Unconfirmed) A (As 0018 for Area A )

0209 PA Device A (As 0009 for Area A ) 0219 Ready A (As 0019 for Area A )

0210 Fire Reset A (As 0010 for Area A ) 0220 Exit Starts A (As 0020 for Area A )

Then this pattern repeats for all other areas other areas so that:

0222-0240 Area B, 0242-0260 Area C, 0262-0280 Area D, 0282-0300 Area 0,

0302-0320 Area 1, 0322-0340 Area 2, 0342-0360 Area 3

0500 Lighthouse Any: if any allocated area is armed –the output will activate, if any armed area then

goes into alarm – the output will pulse (like a flashing light for example)

0501 Lighthouse All: If all allocated areas is arm –the output will activate, if any armed area goes into

alarm (while all allocated areas are armed)– the output will pulse (like a flashing light for example)

0502-0505 Lighthouse Area A – D: If the specified areas are armed the output will activate, if any specified

armed area then goes into alarm – the output will pulse (like a flashing light for example)

0506-0509 Lighthouse Area 0 – 3: If the specified areas are armed the output will activate, if any specified

armed area then goes into alarm – the output will pulse (like a flashing light for example)

0620-0639 Logic Gates 0-20: For use with Insite UDL software.

1001-1046 Active when zones/inputs opened and close when zone/input is closed

*The use of pulsed or latched keyswitch will make the system unable to comply with EN50131-1

PCX 46 Programming Reference

Page: 15

5.5 Install Keypads and Readers?

Ensure that all keypads and readers are addressed correctly before enabling them in this function.

NOTE: Care should be taken to ensure that every area that can be armed, or to which an zone/input is

allocated, can be disarmed by at least one keypad/tag reader.

5.5.1 Device Address

Address [0] is reserved for the first LCD keypad on the bus. In the addresses from 1 to 5 it is possible

to allocate external wired readers or LCD keypads.

5.5.2 Device Type

The device types that are possible to program are LCD keypads [0] or Readers [1].

5.5.3 Reader Device Type

This option will only appear when you program a Reader into the system. You can then select how you

would like the Reader to operate.

Arm/Disarm

This will make the Reader act like a normal keypad (arming/disarming the areas etc.)

Device Arms Areas: This feature programs which area(s) the reader can arm.

Device Disarms: This feature programs which area(s) the reader can disarm.

Device in Area: This feature programs in which area(s) the reader is active.

Device Name: Enter the name of the device for example: ‘Front Door’.

Enter Number: Enter a number of the device, such as: ‘Reader 01’

Zone Description: Enter a description /any additional information that is helpful.

Arm/Disarm Sub-Area

A reader can be used to create sub-areas controlled independently from the area.

Add Zones: Each sub-area may consist of any number of zones/inputs, all of which must be allocated

to the same area. No zone/input may be allocated to more than one sub-area. Entry Delay zone/input

types cannot be allocated to a sub-area and in the sub-area the arming/disarming of the zones/inputs

is immediate without delay timers. The sub-areas can be operated by proximity tag, or by key (or

other) switch wired into the first zone/input on the tag reader. Notice the proximity Tags for sub-area

control are programmed through the Manager menu in ‘LEARN USER CODES KEYFOBS & TAGS’. The

reader provides ‘Alarm’ and ‘Ready’ outputs dedicated to that sub-area. It also provides relevant

indications, including Arm/Disarm status, so should always be located adjacent to the controlling Key

switch where this is used. Sub-Area Arms: If this option is selected as ‘If Area Armed’ then the sub-

area will always arm when the area in which is it located is armed. If selected as ‘Never’ it will always

require manual arming from the tag. The sub-area must ALWAYS be disarmed manually. An additional

option is available in the ‘COMMUNICATIONS’ -> ‘Digi Modem Signalling’ -> custom ‘Event Type’

options, called ‘S-Area Alarm-Rst’ to permit an abort signal to be generated by silencing an alarm at

the Reader after an alarm has been generated in the sub-area.

Action Status Notes

Disarmed Detectors within sub-areas

are inactive

‘Disarmed’ indication lit

Sub-areas zone/input

triggered

No response

Attempt to arm sub-areas

with an open input

- ‘Fault’ LED flashes and

intermittent tone to indicate

‘cannot arm’

Arming with no open inputs Sub-area arms ‘Disarmed’ LED distinguishes

Sub-area zone/input

triggered

Alarm generated ‘Alarm’ LED lights, alarm tone

generated

Valid code entered at a

Keypad whilst alarm in sub-

area is active

Alarm silenced by user code Sub-area remains armed

PCX 46 Programming Reference

Page: 16

Sub-Area Control: The sub area can be controlled by Tag or Zone/Input. When an zone/input is used

to control the sub-area a keyswitch zone/input type should be used and connected to an external key

or switch.

Sub-Area Name: Enter the name of the sub-area such as Private Office.

Enter Number: Enter an appropriate number for the Sub-Area

Zone Description: Enter an appropriate description e.g. the location of the room /area

Assigning Tags to Sub Area Reader: To assign tags to the sub-areas, enter the master manager menu

and select ‘LEARN USER CODES KEYFOBS & TAGS’, add a new user code (tag) and when the prompt

shows “Access Reader”, enter the address of the reader you would like the tag to operate for the sub-

areas.

Access Control

Allows the reader to control doors fitted with electrical locks. On the readers there are 2 zones/inputs

that can also be outputs. They can be connected to the lock for opening and controlling the door.

Lock Open Time: This is the time the door release is going to be active when a valid tag is presented.

Door Open Time: This is the time the door is allowed to be open before triggering an alarm.

Door Contact No: Give the door contact an appropriate number if required (i.e. if monitoring door)

Door Name: Give the door an appropriate name.

Enter Number: Enter an appropriate number e.g. a door, reader, keypad or zone number.

Zone Description: Enter an appropriate description e.g. the location of the door.

NOTE: Access control falls outside the scope of EN50131-1

Disarm Only

Allows the reader to be used to disarm the system only.

Device Disarms: This feature programs which area(s) the reader can disarm.

Device in Area: This feature programs in which area(s) the reader is active.

Device Name: Enter the name of the door such as Front Door.

Enter Number: Enter an appropriate number e.g. a door, reader, keypad or zone number.

Zone Description: Enter an appropriate description e.g. the location of the door/reader.

Entry Control

Allows the reader to be used as arm/disarm Device and access control.

Device Arms Areas: This feature programs which area(s) the reader can arm.

Device Disarms: This feature programs which area(s) the reader can disarm.

Device in Area: This feature programs in which area(s) the reader is active.

Lock Open Time: This is the time the door release is going to be active when a valid tag is presented.

Door Open Time: This is the time the door is allowed to be open before triggering an alarm.

Door Contact No: Give the door contact an appropriate number if required (i.e. if monitoring door)

Door Name: Give the door an appropriate name.

Enter Number: Enter an appropriate number e.g. a door, reader, keypad or zone number.

Zone Description: Enter an appropriate description e.g. the location of the door.

Keypad Device Type

Device Arms Areas: This feature programs which area(s) the keypad can arm.

Device Disarms: This feature programs which area(s) the keypad can disarm.

Device in Area: This feature programs in which area(s) the keypad is active.

Device Name: Enter an appropriate name for the device.

Enter Number: Enter an appropriate number e.g. keypad 1.

Zone Description: Enter an appropriate description e.g. the location of the keypad.

PCX 46 Programming Reference

Page: 17

5.6 Program Timers?

Timers Description Options

Entry Time 1

Entry Time 2

Programmes the entry time for each area. If entry time is started at a

door programmed in multiple areas, the longest time will apply. Entry

time 1 will apply to any zones/inputs programmed as “Entry Delay 1”

type, and Entry Time 2 will apply to any zones/inputs programmed as

“Entry Delay 2” type. Ensure that timer is no longer than 45 seconds in

order to comply with EN50131-1.

0-255

seconds

Exit Time Programs the exit time for each area. 0 – 255

seconds

Bell Time Cut off time for external sounder. Separate for each area. Repeat above

steps for each of the PCX 46 App areas programmed on your system.

02 – 15

minutes

Bell Delay Delay after burglary alarm before bell activation.

NOT valid within 3 minutes of final arm, or after entry time started. If

‘Silent 1st Alarm’ selected in alarm responses, delay commences at

confirmed alarm.

0-20

minutes

Strobe Time The duration of time the strobe output remains live after the bell time

ends, ‘99’ means endless.

0-99

minutes

Number

Re-arms

Number of times system re-arms after bell time ends. Re-arm number

applies to each area, and does not affect emergency alarms. ‘9’ = ‘always

re-arm’.

0 – 9

AC Fail

Delay

Time delay before mains failure or technical alarm signalled. ‘250’ = never

alarms. System change-over to battery supply and associated ‘alert’

indication is always immediate. Mains Fail message on keypad not

permitted until valid code entry.

0-250

minutes

Double

Knock

Length of filter period applied to inputs with ‘Double Knock’ input

attribute.

0 – 75

seconds

Entry Alarm

Signal Delay

Delays ‘Burglary’ alarm signalling if an alarm is generated by deviation

from the entry route. Delay Send Entry must be programmed for a

minimum of 30 seconds to comply with EN50131-1.

0-255

seconds

Line Fault

Delay

Duration of Telecom (GSM) Line Fault before ‘Line Fault’ alarm triggered,

‘250’ endless.

0-250

seconds

Arm Fail

Time

If a system has not been armed within the entry delay time, for example

door left open the Arm Fail Time will take over and at the expiry of this

time an alarm will be created. This time should be longer than the Entry

Delay time.

0-255

seconds

Guard Code

Delay

Minimum time an alarm must have been present before a ‘Guard’ code

will be accepted to disarm.

0-10

minutes

Fire Bell

Time

Cut off time for fire alarm. ‘99’ = endless. 1 – 99

minutes

Activity

Timer

This is used in conjunction with the input attribute ‘Activity Zone’, and will

monitor the chosen zone/input for the selected number of days. At

expiration of timer, and if the zone/input has not opened within that time,

then this will be stored in the panel log. Non Activity fault and there will

be an output activated if programmed to it. Send SMS message if “Special

Log” is on.

0-14

days

Activity

Hours

This is used in conjunction with the input attribute ‘Activity Zone’, and will

monitor the chosen zone/input for the selected number of hours. At

expiration of timer, and if the zone/input has not opened within that time,

then this will be stored in the panel log. Non Activity fault and there will

be an output activated if programmed to it. Send SMS message if “Special

Log” is on.

00-23

hours

Pulsed

Burglar Any

This option sets up the duration of the pulse of an output programmed as

“Pulsed Burglary Any” activates after a burglary alarm.

0-255

seconds

PCX 46 Programming Reference

Page: 18

WLs

Supervision

Time

This is the time window before a supervision fault will be signalled. For

example: if the time is set for 2 hours, then any device that doesn’t

communicate with the PCX 46 App within that period will cause a

supervision fault. Must be programmed to 2 hours or less for compliance

to EN 50131.

0-99

hours

WLs

Jamming

Time

This is the time window that if a wireless device had its signal ‘blocked’ a

fault would display. For example, if the time is set for 30 seconds, then if

a wireless device is ‘jammed’ longer than 30 seconds a fault will be

displayed.

Must be set to 30 seconds or less (but not zero) for compliance to EN

50131.

0-100

seconds

Service

Timer

This is a timer that can be programmed in days, and will display a

message to the user warning that a service is due. An engineer code will

clear the message.

0-734

5.1 Change Codes?

All codes may be 4, 5, or 6 digits long and also can be assigned as proximity tags and keyfobs. 100 user

codes are available.

NOTES: Only Duress/Guard, Master Manager and Engineer codes can be changed by the engineer. User

codes can only be changed by the Master Manager from the Master Manager menu. The Master User and

Engineer Codes cannot be deleted.

User Arm and Disarm System. Also for Access Control and Sub

Area Control functions

Programmed by

Manager only.

Manager

Default: 1234

Arm and Disarm System. Also access to Manager menu

functions

Programmed by

Manager or Engineer.

Engineer

Default: 9999

Access to all engineering functions; also arm/disarm

system for test purposes.

Programmed by

Engineer.

Duress Disarm system, generating silent ‘Duress’ signal. Programmed by

Engineer.

Guard Disarm system, but only after an alarm has been active

for a minimum time (programmable). Also arm system.

An output type is available to activate whenever this code

is used.

Programmed by

Engineer.

5.1.1 Change Duress/Guard Codes?

Choose Code Number

If a code or tag is already allocated, the display will show [******]. Press the key to clear the

code.

Choose Code Number User Type

The user type can be Duress [2] or Guard [3].

5.1.2 Duress Code

The Duress code can arm or disarm the system and if used a Duress communication event will be

sent. An output type is available to activate whenever this code is used (Duress type 008 - see page

12 - 13 Program Outputs).

User In Area

Choose the area(s) the code is active in

User In AreaUser Arm Options

[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.

[1] Disarm Only: The code will only disarm the areas selected in the previous option.

[2] Arm Only: The code will only arm the areas selected in the previous option.

[3] None: No option programmed.

PCX 46 Programming Reference

Page: 19

User In AreaUser Arm OptionsArm Area Choice

If a user code is allocated to more than one area and the ‘Arm Area Choice’ option is set to NO, the

code will automatically arm all areas it has been allocated to in the same time. If the Arm Area Choice

has been set to YES then the user will be given the ability to choose which area to arm when the

arming procedure has been activated.

User In AreaUser Arm OptionsArm Area ChoiceUser Name

Write the name of the user of this code.

5.1.3 Guard Code

This code can disarm the system, but only after an alarm has been active for a minimum time

programmable in the timers. Use of this code will generate a normal user arm/disarm event. An

output type is available to signal whenever this code is used.

User In Area

Choose the area the code is active in

User In AreaUser Arm Options

[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.

[1] Disarm Only: The code will only disarm the areas selected in the previous option.

[2] Arm Only: The code will only arm the areas selected in the previous option.

[3] None: No option programmed.

User In AreaUser Arm OptionsArm Area Choice

If user code is allocated to more than one area and the ‘Arm Area Choice’ option is set to NO, the

code will automatically arm all areas it has been allocated to in the same time. If the Arm Area Choice

has been set to YES then the user will be given the ability to choose which area to arm when the

arming procedure has been activated.

User In AreaUser Arm OptionsArm Area ChoiceUser Name

Write the name of the user of this code.

NOTE: For both duress and guard codes is possible to program a tag too. If a tag is programmed it

has to be associated to a reader.

5.1.4 Change Master Manager Code

If a code or tag is already allocated, the display will show [******]. Press the key to clear the

code and use the numeric keys to input the new code. This option allows the engineer to change the

Master Manager code should this have been lost or forgotten.

User In Area

Choose the area the code is active in

User In AreaUser Arm Options

[0] Disarm/Arm: The code will arm and disarm the areas selected in the previous option.

[1] Disarm Only: The code will only disarm the areas selected in the previous option.

[2] Arm Only: The code will only arm the areas selected in the previous option.

[3] None: No option programmed.

User In AreaUser Arm OptionsArm Area Choice

If user code is allocated to more than one area and the ‘Arm Area Choice’ option is set to NO, the

code will automatically arm all areas it has been allocated to in the same time. If the Arm Area Choice

has been set to YES then the user will be given the ability to choose which area to arm when the

arming procedure has been activated.

User In AreaUser Arm OptionsArm Area ChoiceUser Name

Write the name of the user of this code.

5.1.5 Change Engineer Code

If a code or tag is already allocated, the display will show [******]. Press the key to clear the

code and use the numeric keys to input the new code.

PCX 46 Programming Reference

Page: 20

5.2 Volume Control?

The Volume Control function applies to both the buzzer and the internal sounder.

5.2.1 Area Entry Tone Volume