Pyronix Enforcer X Series User manual

ENFORCER X
USER GUIDE
Document SAP:102032020-01

2ENFORCER X USER GUIDE
CONTENTS
HomeControl2.0 4
Arming Devices 5
Wired Keypads 5
Keypad keys 5
Keypad LEDs 5
Wireless Keyfobs 5
Locking the keyfob 5
Arming the System 6
Arming a multi-area system at a Keypad 6
Arming all areas 6
Arming individual areas 6
Arming a Single Area System at a Keypad 7
Using the Wireless Keyfob 8
Disarming the System 9
Disarming a Multi-Area System at a Keypad 9
Disarming a Single Area System at a Keypad 10
Using the Wireless Keyfob 10
Disarming After an Alarm 11
Using a PIN Code or Proximity Tag 11
Using the Wireless Keyfob 11
Fault Indications & Unable to Arm 12
Fault Indications 12
Control panel 12
Unable to Arm 12
Control panel indication 12
Advanced Functions 13
Chime 13
Omitting Zones 13
Keypad PA 13
Master Manager Mode Overview 14
Entering Master Manager Mode 15
Exiting Master Manager Mode 15
Master Manager Mode Options 15
Omit Zones 15
Operate User Outputs 15
Date & Time 16
Learn User Codes Keyfobs & Tags 16
Area arm choice 17
Adding a new user (code or proximity tag) 17
Adding a new user (keyfob) 18
Deleting or changing a user 18
Change Master Manager code 19
Review Logs 19
Wifi-Setup 20
Setup with WPS 20
Wi-Fi SSID 20
Wi-Fi password 21
Wi-Fi signal value 21
SMS Phonebook 21
Voice Phonebook 21
HomeControl2.0 Smart Device App 22
Getting Started 22
Adding a system via QR code 22
Adding a system via short code 23

3
ENFORCER X USER GUIDE
Basic Controls 24
Connecting to the panel 24
Biometric authorisation 24
Intruder system homescreen 25
HomeControl2.0 App Icons 26
Installation Information 27
Installation Company Information 27

4ENFORCER X USER GUIDE
HOMECONTROL2.0
Simple and intuitive to use
Constantly evolving
Detailed history of events
Biometric login
(FaceID/Touch ID (iOS) and Android equivalents)
Geofence alerts for easy reminders
Smart plug control
Voice push notifications
https://bit.ly/2Pi2GZN
Scan the QR code to find out more and to download HomeControl2.0
Extending the capabilities of security control

5
ENFORCER X USER GUIDE
ARMING DEVICES
WIRED KEYPADS
Keypad keys
a= Exits to day mode from main menu and selects level A when arming.
b= Moves backwards in menus and selects level B when arming.
c= Enables chime, displays additional information in the event log, and
selects level C when arming.
d= Moves forward in the log, scrolls between options, enables code entry
to master or user menus and selects level D when arming.
fp= Not used unless specifically enabled by installation company.
[]= Directional buttons and enables/disables functions.
f= Enters menus and accepts programming preferences.
h= Cancels items, resets the panel and moves to next item in a menu item.
Keypad LEDs
Alert LED
Indicates there is
information waiting to
be read.
Alarm LED
Shows alarm
activations.
Tamper LED
Shows tamper
activations.
Fault LED
Shows system faults.
Disarmed LED
Shows system is
disarmed.
Proximity tag LED
Present tag here to
arm/disarm system.
WIRELESS KEYFOBS
The wireless keyfob has four buttons that may be programmed for specific purposes, these options are programmed in the
‘LEARN USER CODES KEYFOBS & TAGS?’ section.
Locking the keyfob
All four buttons on the keyfob may be locked so that any accidental presses will not affect your wireless alarm system. For
example, this protects the buttons from being pressed accidentally if a keyfob is in someone’s pocket.
OR OR
5 seconds 5 seconds
Enforcer X
Time 10:09 c
Extending the capabilities of security control

6ENFORCER X USER GUIDE
ARMING THE SYSTEM
Example set-up
This example will be used to refer to throughout this section to further explain the arming procedure.
• User 001 has access to areas 01, 02, 03 and 04.
• User 002 has access to areas 01 and 02.
• User 003 has access to area 01.
A B C D
Zone 01
Zone 02
Zone 03
Zone 04 Zone 05
Zone 06
Zone 07
Zone 08 Zone 09
Zone 10
Zone 11
Zone 12
AREA 01
A B C D
Zone 13
Zone 14
Zone 15
Zone 16
Zone 17 Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
AREA 02
A B C D
Zone 25
Zone 26
Zone 27
Zone 28 Zone 29 Zone 30
Zone 31
Zone 32
Zone 33
Zone 34
Zone 35
Zone 36
AREA 03
A B C D
Zone 37
Zone 38 Zone 39
Zone 40
Zone 41
Zone 42
Zone 43
Zone 44 Zone 45
Zone 46 Zone 47 Zone 48
AREA 04
AREAS
LEVELS
ZONES
etc.
etc.
etc.
ARMING A MULTIAREA SYSTEM AT A KEYPAD
Arming all areas
Enter a valid PIN code or present a valid tag to the symbol. Enter Your Code
[******]
To arm all areas level A, press f.Arm All Areas?
The keypad will now display the exit timer, leave the building via the
agreed exit route and make sure the exit door is closed properly. Arming [028]
Area 02
Arming individual areas
Please note: If the keypad is left without a button press for 10 seconds, the display will return to day mode.
Enter a valid PIN code or present a valid tag to the symbol. Enter Your Code
[******]
Press hto arm individual area(s) and level(s). Arm All Areas?
Press fto arm individual area(s) and level(s). Arm Individual
Areas?
Using the numerical keys, enter the number of the area that is to be
armed or press b/d to scroll through the areas accessible
to that user.
Arm [01] [ABCD]
Area 01

7
ENFORCER X USER GUIDE
Once the area to be armed is on the display, use a, b, c
or dto select the level. Once selected, press f.
Example referral
If Area 02 level B was selected, the following zones will arm:
• Zones 16-18
If Area 03 level D was selected, the following zones will arm:
• Zones 34-36
Arm [02] [*B**]
Level B
Arm [03] [***D]
Level D
The keypad will now display ‘Arm Another Area?’. Press fto
arm another area or hto start the exit timer. Arm Another
Area?
The keypad will now display the exit timer, leave the building via the
agreed exit route and make sure the exit door is closed properly. Arming [028]
Area 02
ARMING A SINGLE AREA SYSTEM AT A KEYPAD
Enter a valid PIN code or present a valid tag to the symbol. Enter Your Code
[******]
Using a, b, cor d, enter the level that is to be armed
then press f.Arm [01] [A***]
Level A
The keypad will now display the exit timer, leave the building via the
agreed exit route and make sure the exit door is closed properly. Arming [028]
Area 01

8ENFORCER X USER GUIDE
USING A PROXIMITY TAG AT A READER
Present a proximity tag to the reader and the system will begin the exit time immediately.
Please note: The system will arm depending on a combination of permissions programmed to the
reader and the access the user has. Speak to the installation company for more details.
USING THE WIRELESS KEYFOB
To arm via a keyfob. Pressand hold for less than 2 seconds.
The keyfob LED will start to flash green indicating that the system is starting to
arm.
‘Please wait arming wireless’ will be displayed on the keypad and the
programmed area will begin to arm.
To ‘quick arm’, press and hold thekey again for four seconds.
Once armed, the keyfob LED will illuminate RED indicating that the system is
now armed.
<2 seconds

9
ENFORCER X USER GUIDE
DISARMING THE SYSTEM
DISARMING A MULTIAREA SYSTEM AT A KEYPAD
Enter the building, the ‘entry time’ will start. ENTRY TIME [30]
Enter a valid PIN code or present a valid tag to the symbol as
shown. Enter Your Code
[******]
Press h.
Please note: This option will only appear if there are more areas
that can be armed.
Arm All Areas?
Level [A ]
Press h.
Please note: This option will only appear if there are more areas
that can be armed.
Arm Individual
Areas?
To disarm all the areas, press f. To disarm individual areas press
h.Disarm All
Areas?
To disarm an individual area, press f.Disarm Individ.
Areas?
Enter the number of the area that is to be disarmed, and press f.Disarm Area [01]
Area 01
The keypad will now display ‘Disarm Another Area?’. Press f
to disarm another area or hto disarm the selected areas. Disarm Another
Area?
If all areas are disarmed, the keypad will return to day mode.
If there are still armed areas, these will now be displayed on the
keypad LCD. Press hto return to day mode.
Armed
Area 02
Please note: If ‘disarm choice’ is disabled then the system will automatically disarm the areas armed once a valid
user code or tag is presented.

10 ENFORCER X USER GUIDE
DISARMING A SINGLE AREA SYSTEM AT A KEYPAD
Enter the building, the ‘entry time’ will start. ENTRY TIME [30]
Enter a valid PIN code or present a valid tag to the symbol as
shown. Enter Your Code
[******]
The keypad will return to day mode. Alarm Panel
Time 10:09 c
USING THE WIRELESS KEYFOB
To disarm via a keyfob. Press .
The keyfob LED will flash green indicating that the system has disarmed.
Please note: Disarming with a keyfob will only be allowed if your
installation company has enabled this.
<2 seconds

11
ENFORCER X USER GUIDE
DISARMING AFTER AN ALARM
USING A PIN CODE OR PROXIMITY TAG
Enter a valid PIN code or present a valid tag to the symbol as
shown. Enter Your Code
[******]
The alarm or tamper symbol will flash indicating there has been an
activation and the keypad will display which zone has activated. Alarm Silenced
Press hto reset the system.
Please note: If the keypad displays ‘Restore required’, please
contact the installation company.
Alarm Panel
Time 10:09 c
USING THE WIRELESS KEYFOB
To disarm via a keyfob. Press .
The keyfob LED will start to flash green indicating that the system has disarmed.
Rearming the system after an alarm can only be done at the keypad.
Please note: Disarming with a keyfob will only be allowed if your
installation company has enabled this.
<2 seconds

12 ENFORCER X USER GUIDE
FAULT INDICATIONS & UNABLE TO ARM
FAULT INDICATIONS
Control panel
Any faults that occur on the system will be easily recognised by the
flashing ALERT LED. Alarm Panel
Time 10:09 c
To see what the fault is, enter a valid PIN code, or present a valid
tag, or press on the keyfob.
Depending on how the system has been programmed by your
installation company, it may be possible to arm the system with a
fault, to do this press f.
Control Panel
Battery Fault
Please note: Any fault may affect the overall performance of your alarm control panel and therefore your
installation company should be contacted for further assistance if any fault is active.
UNABLE TO ARM
Control panel indication
If ‘unable to arm’ is displayed, it indicates that a zone is open and
the area where the zone is should be checked for open windows,
pets, movement etc.
If the problem cannot be solved contact your installation company,
or omit the zone.
Unable To Arm
Zone 001

13
ENFORCER X USER GUIDE
ADVANCED FUNCTIONS
CHIME
The chime can be used for any zone on the system. This can be
programmed by your installation company.
To enable the chime on the keypad, when the time is displayed,
press c.
Press cagain to cycle through ‘c’, ‘C’ and nothing.
Cycle Display Chime Noise
Nothing N/A Silent
Lower case c c Chime from keypad
Capital c C Chime from keypad and speakers on
the system
Alarm Panel
Time 10:09 c
OMITTING ZONES
On occasion, a detector may need to be isolated if a room is
occupied.
Start the arming procedure.
Once the exit timer is on the display, press f.
Select the zones that need to be omitted.
Press h.
After 10 seconds the exit time continues.
Omit Zone?
Z1
Please note: Zones have to be programmed as omittable by your installation company for this feature to operate.
KEYPAD PA
A ‘panic’ alarm will be generated when 1and 7are
pressed and held down for 2 seconds. This feature, along with the
length of time required for the keys to be pressed, are programmed
by the installation company.
Alarm Silenced
2 Key PA
Please note: The keyfob can also be programmed to initiate a panic alarm. All panic alarms including duress codes
must be enabled by the installation company.

14 ENFORCER X USER GUIDE
MASTER MANAGER MODE OVERVIEW
The Master Manager menu has the following functions:
Please note: Some of the following menus may not appear. The menu is dynamic, meaning that it will only display
relevant menus which are impacted by equipment and programming. This is nothing to be concerned about.
Omit Zones?
Omits any zone except PA and/or fire.
Operate User Outputs?
Activates/deactivates user automation outputs that are used to
remotely activate devices, such as electronic gates & lights.
Date and Time?
Programs the date and time.
Learn User Codes Keyfobs & Tags?
Adds/Edits/Deletes User PIN codes, tags and keyfobs.
Review Log?
Displays all event log information.
Wi-Fi Setup?
Adds or changes a Wi-Fi connection with your router.
SMS Phonebook?
If SMS texting is enabled, there can be up to 10 mobile numbers
programmed to send SMS alarms. .
Please note: Third party SIM cards only.
Voice Phonebook?
Edits the telephone numbers that the panel is programmed to send
voice messages to.
Walk Test?
Tests each zone.
Bell Test?
Tests all external sounders (wired or wireless).
Allow Engineer Menu?
Enables or disables engineer access.
Block Remote Arming?
Blocks remote arming from the web browser.
Setup App?
Displays short code for adding the system to HomeControl2.0.
Block UDL?
Blocks uploading/downloading from the web browser.
System Sounds Demo?
Demonstrates all the sounds of the alarm system.
Exit Manager Mode?
Please note: A User Code will only access the ‘User Menu’ which includes the functions: ‘Operate User Outputs’,
‘Omit Zones’, ‘Change Code’, ‘Review Log’, ‘Walk Test’, ‘Bell Test’. ‘Allow Engineer Menu’, and ‘Exit User Menu’.
MASTER MANAGER MENU
OMIT ZONES?
OPERATE USER OUTPUTS?
DATE & TIME?
LEARN USER CODES KEYFOBS & TAGS?
WI-FI SETUP?
REVIEW LOG?
SMS PHONEBOOK?
VOICE PHONEBOOK?
WALK TEST?
BELL TEST?
ALLOW ENGR MENU?
BLOCK REMOTE ARMING?
BLOCK UDL?
SETUP APP?
SYSTEM SOUNDS DEMO?
EXIT MANAGER MODE?

15
ENFORCER X USER GUIDE
ENTERING MASTER MANAGER MODE
Press d.
Enter the Master Manager code or present the Master Manager
tag.
Press bor hto scroll through the different functions.
Enter Your Code
[ ]
EXITING MASTER MANAGER MODE
Press bor hkeys to scroll through until ‘EXIT MANAGER
MODE?’ is displayed.
Press f.
Or, when a main menu item is displayed (capital letters) press a.
EXIT MANAGER
MODE?
MASTER MANAGER MODE OPTIONS
OMIT ZONES
OMIT ZONES?
Press bor hto scroll to ‘OMIT ZONES?’.
Press fOMIT ZONES?
Enter the zones you require to be omitted for the next arming
procedure.
Press f.
Press hto return to the main menu.
Omit Zone[---]
Please note: This option will not omit any PA and/or fire zones.
OPERATE USER OUTPUTS
OPERATE USER OUTPUTS?
This option toggles outputs that are programmed as ‘User Outputs’.
Use the numerical keys or scroll using [or ]until reaching the
user output to trigger. Pressing ftoggles between on and off. Select Output
[01]

16 ENFORCER X USER GUIDE
DATE & TIME
DATE & TIME?
All log entries are date and time stamped. This can also programmed in the Master Manager Mode. The time is also
shown on the LCD in ‘Day Mode’ .
Please note: Powering down the system will reset the time and date information unless communications are
configured and the system reconnects to the data path on power up.
Timezone
Choose the timezone by scrolling through with band dor enter the number of the city if known.
For example: [205] London, [018] Athens, [217] Madrid, and [268] Oslo.
Change year
For the year 2022, enter 22.
Change month
For March, enter 03.
Change day
For 31st, enter 31.
Change hours
Use 24 hour clock format. For 8pm enter 20:00.
Change minutes
For 7:30, enter 30.
Time Prompt
If set to ‘[1] Yes’ the panel will prompt the user to manually update the time if the panel loses the current time; such as in the
event of a power outage followed by depletion of the back up battery.
LEARN USER CODES KEYFOBS & TAGS
LEARN USER CODES KEYFOBS & TAGS?
Add New User?
Delete/Change User?
Change Master Manager Code?
The ‘LEARN USER CODES KEYFOBS & TAGS?’ function allows adding, editing and deleting of both master manager
and user codes, tags and keyfobs.
The control panel can have up to 500 users programmed. Each of the users are allocated a code, tag or a wireless
keyfob.
Please note: A maximum of 32 users can have a wireless keyfob allocated with the addition of a wireless ZEM to
the system.

17
ENFORCER X USER GUIDE
Area arm choice
Area arm choice allows you to choose which level/area to arm if a user code or tag is assigned to one or more levels/
areas. If this function is disabled, when a user code is entered or proximity tag presented, the system will automatically arm
the areas/levels that the user is assigned to.
Please note: Any proximity tags used on a standalone tag reader must have area arm choice set to ‘No’.
Adding a new user (code or proximity tag)
Press bor hto scroll to ‘LEARN USER CODES KEYFOBS
& TAGS?’.
Press f.
LEARN USER CODES
KEYFOBS & TAGS?
To add a new code, tag, or keyfob press f. Press hto delete
or change a user code (see further down for details). Add New User?
Press [or ]to choose a user number. Press f.Empty [01]
Enter the new code or present a tag. Once ‘asterisks’ appear, the
tag or user code will be now assigned to this user. Press f.Enter User Code
[******]
Press [or ]to choose between 'User' or 'Manager'. Press
f.User Type
User [0]
The permissions must now be programmed for this user. Press [or
]to toggle between ‘Yes’ or ‘No’ and press fto move on to
the next area.
Once finished, press h.
User in Area
Area [01] Yes
Press huntil the LCD displays ‘LEARN USER CODES KEYFOBS
& TAGS?’ then press ato exit and save programming. LEARN USER CODES
KEYFOBS & TAGS?

18 ENFORCER X USER GUIDE
Adding a new user (keyfob)
Press bor hto scroll to ‘LEARN USER CODES KEYFOBS
& TAGS?’.
Press f.
LEARN USER CODES
KEYFOBS & TAGS?
To add a new user, press f. Press hto delete or change a
user code (see ‘Deleting or Changing a User’). Add New User?
Press [or ]to choose a user number. Press f.Empty [01]
Press and hold Qfor 3 seconds and release. On release, ‘asterisks’
appear in the brackets and the keyfob is assigned to this user.
Press f.
Enter User Code
[******]
The 'User Name' will be displayed on the keypad.
Enter a user name for the keyfob and press f.User Name
_
The buttons on the keyfob can now be tailored to the users needs.
Press [or ]to choose the button to program. Press f.Select Button
Lock [1]
Press [or ]to choose the action assigned to the button. Press
f.Button Action[2]
Arm Area
Press huntil the LCD displays ‘LEARN USER CODES KEYFOBS
& TAGS?’ then press ato exit and save programming. LEARN USER CODES
KEYFOBS & TAGS?
Deleting or changing a user
Deleting a user
Press fto delete or change a user or hto change the
Master Manager code. See ‘Change Master Manager Code’. Delete/Change
User?
Press [or ]to scroll through the users, or enter the user number
and press f.Code [01]
Press fto delete a user, or press hto change a user. Delete User?

19
ENFORCER X USER GUIDE
Change user
Press fto change a user code, and follow the screen shots
previously shown to edit either code, tag or keyfob permissions. Change User?
Change Master Manager code
To change the Master Manager Code, press f. Change Master
Manager Code?
Press cthen enter the new code or present a tag. Press f. Manager Code
[******]
The permissions can now be edited for the manager. Press [or
]to toggle between ‘Yes’ or ‘No’ and press fto move on to
the next area.
User in Area
Area [01] Yes
Press huntil the LCD displays ‘LEARN USER CODES KEYFOBS
& TAGS?’ then press ato exit and save programming. LEARN USER CODES
KEYFOBS & TAGS?
REVIEW LOGS
REVIEW LOG?
Panel Log?
Access/Ctrl Log?
Voice Log?
The ‘Review Logs’ function monitors all operational information of the wireless alarm system, such as arming/disarming
information and alarm activations etc.
Press bor hto scroll to ‘REVIEW LOGS?’.
Press f.REVIEW LOGS?
Press f.Panel Log?
The most recent event will be displayed, press bor dto scroll
backwards and forwards through the log. 09/09 10:09:00
User Added
Press the ckey to show more information (such as which zone
activated, or which user armed the system etc.) Daniel

20 ENFORCER X USER GUIDE
WIFISETUP
WI-FI SETUP?
Setup with WPS?
Wi-Fi SSID?
Wi-Fi Password?
WiFi Signal Val.
Setup with WPS
1. Go into the Master Manager menu. Press h until the
option ‘WI-FI SETUP?’ is displayed. Press f.WI-FI SETUP?
2. ‘Setup with WPS?’ will now be displayed, press fand
then fagain when the system asks ‘Are You Sure?’ Setup with WPS?
3. ‘Connecting WPS Please Wait’ will now be displayed, whilst
the system searches for a router. Connecting WPS
Please Wait
4. At this point, the router that the system is to connect to should be put in to WPS mode.
5. The panel will display a message to indicate when the system has successfully connected.
Wi-Fi SSID
1. Go into the Master Manager menu. Press h until the
option ‘WI-FI SETUP?’ is displayed. Press f.WI-FI SETUP?
2. ‘Setup with WPS?’ will now be displayed, press h.Setup with WPS?
3. ‘Wi-Fi SSID?’ will now be displayed, press fand enter
the SSID (name of the wireless network). Press fto return
to ‘Wi-Fi SSID?’.
Please note: Additional characters can be accessed by
repeatedly pressing the 0and 1keys to scroll through the
available glyphs.
Wi-Fi SSID?