QOLSYS QS-1311-P01IQ PINpad User manual

QS-1311-P01_Qolsys IQ PINpad.doc Page 1 of 3 17-Sep-13
www.ResolutionProducts.com
QS-1311-P01 IQ PINpad™
Features
•Secure, 4-digit Code to disarm
•1-button arming
•Red/Green LE arming feedback
•Small, yet comfortable keypad
•Mounts on wall via VHB® tape, or screws
•Secure for carrying in purse or mounting on car visor
•Strong, reliable RF signal.
•4-6 year battery life on CR2032 battery.
Key Instructions
• Enroll as a Key Fob.
•Code programming
efault access code is “1234”.
To change access code: o these steps wit in 4 seconds
1. Enter current 4-digit access code.
2. Press and hold the “1” and “3” keys simultaneously. (after 3
seconds, Red LE will be lit)
3. Enter new 4-digit access code.
(the Green LE will be lit)
Note new access code . BA GUY CANNOT RESET CO E.
So it must be recorded and remembered!
•Enrolling:
1. Refer to the Qolsys control unit installation manual.
2. Put the control panel in RF Learning mode.
•Press both the Stay & Away buttons simultaneously for 3
seconds.
Operation
PINpad
Button Panel Action LED
Stay ARM STAY flashes double red
Away ARM AWAY flashes double red twice
PIN Code ISARM flashes double green
Stay + Away PANIC ALARM flashes red 8 times
POWERED BY
QS-1311-P01_Qolsys IQ PINpad.doc Page 2 of 3 17-Sep-13
www.ResolutionProducts.com
Pictures
Battery Replacement
CR2032 Battery
+ Terminal up
Insert Screwdriver
here
to open
Red/Green
Status LE
Shows command sent
Stay + Away
=
Panic (Enroll)
TO CHANGE PIN CO E:
Current 4-digit access code, and then…
1 + 3 simultaneously  Red LE ,
and then…
Enter New Code

QS-1311-P01_Qolsys IQ PINpad.doc Page 3 of 3 17-Sep-13
www.ResolutionProducts.com
Specifications
Not supervised.
Replacement Battery: CR2032 Lithium / Manganese ioxide
Temperature Range: 0F to 120F
Housing dimensions: 2x2.25x0.33 inches
1-way RF: oes not receive panel status
esign & Manufacture: Resolution Products, Inc.
Specifications subject to change without notice.
Notices
Verify proper enrollment and operation, per control panel installation instructions, at installation.
PINpad™ is a Trademark of Resolution Products, Inc.
Warranty
Qolsys will replace products that are defective in their first two years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.
FCC I : U5X-RE152
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE152